HWATEL RG-58 3D-FB

Contents

HWATEL RG-58 3D-FB Coaxial Cable User Manual

Original RG-58 3D-FB LMR200 50 Ohm Coaxial Cable Feeder for Cellular Signal Booster, Repeater, Amplifier, and Antenna Systems

1. Introduction

This manual provides essential information for the proper installation, operation, and maintenance of your HWATEL RG-58 3D-FB Coaxial Cable. This low-loss cable is designed for reliable signal transmission in various wireless communication systems, including cellular signal boosters, repeaters, amplifiers, and antennas, supporting a wide frequency range from 600MHz to 6000MHz.

2. Specifications

FeatureDescription
BrandHWATEL Original
CertificationCE, FCC, RoHS
StandardRG-58, 3D-FB, SYV-50-3
Impedance50 Ohm
Frequency Range600 - 6000 MHz
ColorWhite
Cable ConstructionCopper Core, Physically Foamed PE, Double High-Density Shielding, Dualable PVC
Available ConnectorsN Male to N Male (default), N Male to SMA Male, N Male to SMA Male with TS9 Adapter, N Male to SMA Male with CRC9 Adapter
Available Lengths0M (Bridge), 3M, 5M, 10M, 15M, 20M, 30M
Package Dimensions (approx.)45cm (L) x 25cm (W) x 8cm (H)
Package Weight (approx.)0.6 kg

Cable Construction Diagram

Cross-section diagram of HWATEL low-loss coaxial cable showing internal layers: Copper Core, Physically Foamed PE, Double High-Density Shielding, and Dualable PVC.
Figure 1: Internal structure of the low-loss coaxial cable.

3. Setup and Installation

The HWATEL RG-58 3D-FB coaxial cable is designed for easy integration into your existing RF system. Follow these general steps for installation:

  1. Identify Components: Ensure you have the correct cable length and connector types (N Male, SMA Male, TS9, CRC9) to match your cellular signal booster, repeater, amplifier, or antenna.
  2. Connect Devices: Carefully align the cable connectors with the corresponding ports on your devices. Gently push and then twist the connector clockwise until it is finger-tight. Do not overtighten, as this can damage the connectors.
  3. Cable Routing: Route the cable along a path that avoids sharp bends, kinks, or excessive tension. Secure the cable using appropriate cable ties or clips to prevent accidental damage or disconnections.
  4. Environmental Considerations: While the cable is robust, protect connectors from moisture and extreme weather conditions if used outdoors.

Packing List Examples

Packing list for 3M cable, showing one HWATEL RG-58 3D-FB cable with N Male to N Male connectors.
Figure 2: Example Packing List for 3M N Male to N Male Cable.
Packing list for 10/15/20/30M cable, showing one HWATEL RG-58 3D-FB cable with N Male to N Male connectors.
Figure 3: Example Packing List for 10/15/20/30M N Male to N Male Cable.
Packing list for 0M Bridge, showing one N Male to N Male bridge connector.
Figure 4: Example Packing List for 0M N Male to N Male Bridge Connector.
Packing list for 20M SMA cable, showing one HWATEL RG-58 3D-FB cable with N Male and SMA Male connectors.
Figure 5: Example Packing List for 20M N Male to SMA Male Cable.
Packing list for 5/10/20M TS9 cable, showing one HWATEL RG-58 3D-FB cable with N Male and SMA Male connectors, and an SMA-TS9 adapter.
Figure 6: Example Packing List for 5/10/20M N Male to SMA Male Cable with TS9 Adapter.
Packing list for 5/10/20M CRC9 cable, showing one HWATEL RG-58 3D-FB cable with N Male and SMA Male connectors, and an SMA-CRC9 adapter.
Figure 7: Example Packing List for 5/10/20M N Male to SMA Male Cable with CRC9 Adapter.

4. Operating Instructions

The HWATEL RG-58 3D-FB coaxial cable is a passive component designed to transmit RF signals with minimal loss. Once properly connected between your RF devices, it operates continuously without requiring user intervention. Its low-loss characteristics ensure efficient signal transfer across its specified frequency range (600-6000 MHz).

5. Maintenance

To ensure the longevity and optimal performance of your coaxial cable, follow these maintenance guidelines:

  • Physical Inspection: Periodically inspect the cable for any signs of physical damage, such as cuts, kinks, or severe bends. Damaged cables should be replaced to prevent signal degradation.
  • Connector Care: Keep connectors clean and free from dust, dirt, or moisture. Use a soft, dry cloth to wipe them if necessary. Ensure connectors are securely fastened but not overtightened.
  • Avoid Stress: Do not pull or yank on the cable. Avoid placing heavy objects on the cable or routing it through high-traffic areas where it could be stepped on or crushed.
  • Environmental Protection: If the cable is installed outdoors, consider using weather-sealing tape or boots around connectors to protect them from moisture ingress.

6. Troubleshooting

If you experience issues with your RF system, consider the following troubleshooting steps related to the coaxial cable:

  • No Signal or Weak Signal:
    • Verify all cable connections are secure and properly tightened.
    • Ensure the correct cable type (RG-58 3D-FB, 50 Ohm) is being used for your application.
    • Inspect the entire length of the cable for any visible damage (kinks, cuts, severe bends).
    • If using adapters (TS9, CRC9), ensure they are correctly attached and functional.
  • Intermittent Signal:
    • Check for loose connections at both ends of the cable.
    • Ensure the cable is not being moved or stressed, which could cause temporary disconnections.
  • Connector Mismatch:
    • Confirm that the connector types on the cable (N Male, SMA Male) and any adapters (TS9, CRC9) match the ports on your devices. An incorrect match will prevent proper signal transfer.

For further assistance, refer to the documentation of your connected RF devices or contact HWATEL support.

7. User Tips

  • Choose the Right Length: Always select the shortest possible cable length that meets your installation needs to minimize signal loss.
  • Match Connectors: Double-check that the cable's connector types (e.g., N Male, SMA Male) and any required adapters (TS9, CRC9) are compatible with your equipment before purchase and installation.
  • Gentle Handling: Coaxial cables, especially their connectors, are sensitive. Handle them gently during installation and avoid excessive force or sharp bends to maintain signal integrity.

8. Warranty and Support

Your HWATEL RG-58 3D-FB Coaxial Cable is manufactured to high-quality standards and is certified with CE, FCC, and RoHS. For specific warranty terms and conditions, please refer to the official HWATEL website or contact your point of purchase.

For technical support or inquiries, please contact HWATEL customer service through their official channels.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.