Introduction
Thank you for choosing the KING KONG X7max Bicycle Headlight. This manual provides detailed instructions for the safe and efficient use of your new headlight. Please read this manual thoroughly before installation and operation, and keep it for future reference.
Setup
1. Battery Installation
The X7max headlight is designed for use with universal 18650 batteries. Ensure correct polarity during installation.
To install the battery:
- Rotate the battery compartment to open it.
- Insert a universal 18650 battery, ensuring the positive (+) and negative (-) terminals align correctly.
- Close the battery compartment by rotating it back into place.
Note: Some special 21700 batteries with positive and negative terminals on the same side may also be compatible. Refer to the battery dimensions for proper fit (18.5 ± 0.3mm diameter, 70 ± 0.5mm length).
2. Mounting the Headlight
The X7max offers various installation methods to suit your cycling needs.
Common mounting options include:
- Handlebar Mount: Use the provided bracket to secure the light to your bicycle's handlebar.
- Helmet Mount: Attach the light to your helmet for an elevated light source.
- GoPro Adapter: An upgraded GoPro adapter allows for versatile mounting on compatible GoPro bases.
3. Remote Control Pairing
The remote control is factory-matched. If re-pairing is needed:
- Ensure the headlight is turned ON.
- Quickly press the light body button three times in a row. The main light will turn off, and the indicator light will turn yellow.
- Press the wireless remote control's power ON/OFF button once.
- The main light will turn on, indicating successful pairing.
Operating Instructions
1. Power On/Off
- To Turn On/Off: Press and hold the light body button for 1 second. When turned on, the low beam gear is remembered.
- Using Remote for On/Off: If the remote control was used to turn off the light, it can also be used to turn it back on. If the light has been off for more than two hours (entering sleep mode), you may need to use the light body button to turn it on.
2. Light Modes and Functions (Light Body Button)
The light body button has five primary functions:
- Power On/Off & Gear Change: Press and hold for 1 second to turn on/off. After turning on, lightly touch the button to cycle through light gears (Low Light, Medium Light, High Light).
- High Beam Mode: Double-click the power button quickly to turn on the high beam. Double-click again to turn off the high beam. The high beam gear is not remembered when turned off.
- Paired Mode: Quick triple hit (three presses).
- Switch Modes: Press and hold for five seconds to switch between different lighting modes (e.g., constant light, warning function).
- Intelligent Mode: Quickly hit the button five times to activate intelligent mode.
3. Warning Function
After turning on the light, continuously press the light body button for 5 seconds to activate the warning function. The light will flash and breathe. You can adjust it by lightly touching the button. To return to constant light mode, press and hold for 5 seconds again. The warning mode is not remembered when the device is turned off.
4. Remote Control Operation
For models with a wireless remote control:
- Switch Button: Short press to switch gears, long press to turn off.
- High Beam Button: Short press for high beam, long press for extremely bright function.
- Four-Button Remote (if applicable): Use the left and right buttons to gradually adjust brightness. Holding for more than 5 seconds allows customization (brightness not stored).
5. Battery Level Indicator
- Green Light: Battery level is sufficient.
- Red Light: Battery level is below 30%, requiring timely charging.
- No Light: Battery is critically low (5%-0%) or off.
6. Charging
The X7max supports Type-C charging. It can be used while charging.
7. Intelligent Smart Mode
In Smart Mode, the light will automatically turn off after 20 seconds of stopping riding. It will turn back on when movement is detected. When the battery is low, it automatically switches to a lower gear to increase battery life.
8. Cut-off Line Light
The headlight features a cut-off line design to prevent dazzling oncoming traffic while providing ample illumination for safe cycling.
Maintenance
1. Battery Replacement
Replace the 18650 battery as needed. After replacing the remote control battery (CR1632 or CR2032), it needs to be re-paired with the headlight.
2. Heat Management
It is normal for the aluminum alloy body of the lamp to heat up during prolonged use. The headlight features an intelligent temperature control system with NTC for precise temperature measurement. When the temperature reaches approximately 52 degrees Celsius, the chip automatically reduces the brightness to cool down and prevent overheating. Once the temperature drops, the brightness will return to its previous level. This mechanism protects the lamp and extends battery life. When riding at high speed, heat dissipation is enhanced through convection.
3. Cleaning
Wipe the exterior of the headlight with a soft, damp cloth. Do not use abrasive cleaners or solvents.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Headlight does not turn on. | Low or depleted battery; incorrect battery installation; light in sleep mode. | Charge or replace battery; check battery polarity; press and hold body button for 1 second. |
| Remote control not working. | Remote battery depleted; remote not paired. | Replace remote battery (CR1632/CR2032); re-pair the remote control (see Setup section). |
| Light dims automatically. | Overheating protection activated. | This is normal. The light will return to full brightness once it cools down. Ensure adequate airflow. |
| Red indicator light is on. | Battery level is below 30%. | Charge the headlight immediately. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | X7max |
| Brand Name | King Kong |
| Type | HEADLIGHTS |
| Body Material | Aluminum alloy |
| Power Supply | Battery (Universal 18650) |
| Battery Capacity | 5000mAh (for X7max-5000mAh variant) |
| Lumen Output | 1200LM (High beam and low beam) |
| Waterproof Level | IPX5 |
| Support Dimmer | 2 - 4 Files (modes) |
| Mounting Placement | Handlebar |
| Dimensions (approx.) | 120mm (Length) x 31mm (Height) x 32mm (Width) |
| Weight (approx.) | 128g |
| Origin | Mainland China |
User Tips
- Remote Control Usage: The remote control is designed for convenience. To save energy, turn the lamp on first using the body button, then use the remote control's power-off button to turn it off. The lamp can be turned on and off freely with the remote within two hours of standby.
- Flashing Mode Activation: To access the flashing modes, ensure the lamp is turned off. Then, hold down the power-on button for five seconds to enter the five-mode setting, which includes two flashing modes and three constant-on modes.
- Normal Heat Generation: It is normal for the bicycle lamp to generate heat during operation. The intelligent temperature control system will automatically reduce brightness if the temperature reaches 52 degrees Celsius to prevent damage and extend battery life. This is a protective feature, not a malfunction.
- Brightness vs. Battery Life: When using the remote control, you may need to choose between maximum brightness and extended battery life. The automatic temperature control will intervene to reduce brightness if the lamp gets too hot, but if the remote control is actively triggered, it may temporarily override this for about one minute before the temperature control re-engages.
Warranty and Support
For detailed warranty information, technical support, or further inquiries, please refer to the official product documentation. A comprehensive user manual in PDF format is available for download: