ANDELI CUT-50Y PRO X

Contents

ANDELI CUT-50Y PRO X Plasma Cutting Machine Instruction Manual

Built-in Compressor 50A 110V/220V

1. Introduction

The ANDELI CUT-50Y PRO X is a versatile plasma cutting machine designed for efficient metal cutting and MMA (Manual Metal Arc) welding. It features a built-in air compressor for convenience, and supports dual voltage input (110V/220V). This manual provides essential information for the safe and effective operation, setup, and maintenance of your machine.

2. Safety Information

WARNING: Improper use of this equipment can cause serious injury or death. Always follow safety precautions.

  • Electrical Shock: Ensure the machine is properly grounded. Do not operate in wet conditions. Always wear dry welding gloves.
  • Fumes and Gases: Welding and cutting produce fumes and gases that can be hazardous to your health. Work in a well-ventilated area.
  • Arc Rays: Arc rays can injure eyes and burn skin. Wear appropriate welding helmet with proper shade and protective clothing.
  • Fire and Explosion: Sparks and hot metal can cause fires. Keep flammable materials away from the work area.
  • Hot Parts: Do not touch hot parts with bare hands. Allow equipment to cool before handling.
  • Personal Protective Equipment: Always wear safety glasses, welding helmet, protective clothing, and gloves.

3. Package Contents

Verify that all items listed below are included in your package:

  • Plasma Cutting Torch FPT-40 4M x 1
  • FPT-40 Plasma Electrode x 10
  • Nozzle 0.9 FPT-40 Plasma x 10
  • Water Separator Air Filter x 1
  • Clip x 2
  • Hose for air x 1
  • Connector for air hose x 2
  • Gloves x 1
  • Negative claw cable x 1
ANDELI CUT-50Y PRO X Plasma Cutting Machine and included accessories
Figure 1: ANDELI CUT-50Y PRO X Plasma Cutting Machine with all included accessories.

4. Product Overview and Panel Introduction

The ANDELI CUT-50Y PRO X features an intuitive control panel and robust design. Familiarize yourself with the main components and controls before operation.

Front panel of the ANDELI CUT-50Y PRO X showing controls
Figure 2: Front Panel Controls
  1. Gas Meter: Displays the output value of air pressure during cutting.
  2. Function Key: Used to switch between CUT (plasma cutting) and MMA (Manual Metal Arc welding) functions.
  3. Air Supply Method Selector: Choose between 'INT' to use the built-in air pump or 'EXT' to use an external air pump.
Digital display on the plasma cutter
Figure 3: Digital Display for current settings.
Diagram of non-HF cut torch components
Figure 4: Non-HF Cut Torch Components (from left to right: Cutting Torch Body, Electrode, Swirl Ring, Nozzle, Nozzle Retaining Cap).

5. Setup Instructions

5.1 Torch and Ground Clamp Connection

Torch connection diagram for CUT and MMA functions
Figure 5: Torch Connection Diagram
  • For CUT Function: Connect the cutting torch to interface ⒈ and the ground clamp to interface ⒊.
  • For MMA Function: Connect the MMA holder to interface ⒉ and the ground clamp to interface ⒊. This model also supports MMA reverse connection: the MMA holder is connected to interface ⒊, and the ground clamp is connected to interface ⒉.

Important: Do not connect all torches to the machine at the same time during the plasma cutting process, as this may affect cutting performance or damage the torch.

5.2 Air Supply Connection

The machine has a built-in air compressor. You can also connect an external air compressor for increased cutting capacity.

  • Built-in Air Pump: Select 'INT' on the air supply method selector. For optimal performance, especially when using the built-in air pump, it is recommended to operate the machine at 220V. The cutting effect may be slightly reduced at 110V.
  • External Air Pump: Select 'EXT' on the air supply method selector. Connect your external air compressor to the designated input.
Built-in low frequency air pump feature
Figure 6: Built-in Low Frequency Air Pump. Note: An external air pump can also be used.

5.3 Consumables

The machine uses an FPT-40 integrated cutting gun. Ensure you have sufficient FPT-40 Plasma Electrodes and Nozzles (0.9) for your work. These are universal consumables and can be purchased from various suppliers.

6. Operating Instructions

6.1 Plasma Cutting

  1. Ensure the machine is properly set up for cutting (torch connected, ground clamp secured to workpiece, air supply selected).
  2. Turn on the machine and select the 'CUT' function using the function key.
  3. Adjust the air pressure using the gas meter to the appropriate level for your material and thickness.
  4. Position the cutting torch over the material to be cut.
  5. Initiate the arc and begin cutting. Maintain a steady hand and consistent travel speed for a clean cut.
Plasma cutting in action
Figure 7: Plasma cutting a metal piece.
Examples of cutting thickness from 1mm to 15mm
Figure 8: Examples of cutting thickness from 1mm to 15mm. The CUT-50Y Pro can cut up to 20mm with stable power supply.
Types of materials that can be cut
Figure 9: The machine is suitable for cutting Angle Steel, Mild Steel, Sheet Metal, and Stainless Steel.

6.2 MMA Welding

  1. Ensure the machine is properly set up for MMA welding (MMA holder connected, ground clamp secured to workpiece).
  2. Turn on the machine and select the 'MMA' function using the function key.
  3. Insert the appropriate welding electrode into the MMA holder.
  4. Adjust the welding current as needed for your electrode and material.
  5. Begin welding, maintaining a stable arc.

6.3 Cutting Thickness and Duty Cycle

  • Built-in Air Pump: Can cut up to 25mm.
  • External Air Pump: Can cut up to a maximum of 30mm.
  • Voltage Impact: The cutting effect will be slightly worse at 110V than at 220V. Ensure stable voltage for optimal air pump performance.
  • Duty Cycle: The built-in compressor is small and not designed for continuous long-duration cutting. It is necessary to allow the machine to rest after short periods of cutting to prevent damage and ensure longevity.
  • Recommended Cutting Thickness: To prolong the life of torch accessories and ensure successful cutting, it is suggested to cut at approximately 70% of the maximum thickness (e.g., for a 25mm max, aim for around 17.5mm).

6.4 Low Frequency Cutting Protection

This machine features a protective mechanism where the cutting arc will break in 3 seconds under vacuum cutting conditions. This is designed to protect the torch nozzle from damage.

Video 1: Demonstration of plasma cutting with the ANDELI CUT-50Y PRO X.

7. Maintenance

Regular maintenance ensures the longevity and optimal performance of your plasma cutting machine.

  • Consumables: Regularly inspect and replace the FPT-40 Plasma Electrodes and Nozzles as they wear out. Worn consumables can lead to poor cut quality and damage to the torch.
  • Air Filter: Check the water separator air filter periodically. Clean or replace the filter element if it appears dirty or clogged to ensure a clean and dry air supply.
  • Cleaning: Keep the machine clean and free from dust and metal particles. Use compressed air to blow out internal components if necessary, ensuring the machine is unplugged.
  • Cables and Connections: Inspect all cables and connections for damage or loose fittings before each use.
  • Ventilation: Ensure the machine's ventilation openings are clear and unobstructed to prevent overheating.

8. Troubleshooting

  • Arc breaks in 3 seconds during cutting: This is a normal protective mechanism for the torch nozzle under vacuum cutting conditions. It indicates the machine is functioning as designed to prevent damage.
  • Poor cutting effect or reduced thickness at 110V: The machine performs optimally at 220V, especially when using the built-in air pump. Ensure your power supply is stable and consider using a 220V connection if available for better results.
  • Unsuccessful cutting or rapid consumable wear: Avoid cutting at the absolute maximum thickness for extended periods. Adhere to the recommended 70% of maximum thickness for prolonged consumable life and consistent cutting performance.
  • No arc or weak arc: Check all connections, ensure the ground clamp has good contact, verify air pressure, and inspect torch consumables for wear.

9. Specifications

Specifications table for ANDELI CUT-50Y PRO X
Figure 10: Detailed Specifications
AttributeMMACUT
Power Supply Voltage(V)AC220±15%
Frequency(Hz)50/60
Power Factor0.76
Efficiency(%)80
Rated Output Power(KW)4.37
Rated Input Power(KW)58.5
Rated Input Current(A)3038
Effective Input Current(A)19.525.5
Welding Current Range(A)20-17015-45
No-Load Voltage(V)70320
Duty cycle (% 40°C 10min)40%: 165
60%: 134
100%: 104
40%: 45
60%: 36
100%: 28
Welding/Cutting Thickness/25mm
Protection ClassIP21S
Insulation ClassH
CoolingAir cooling
Dimension(MM)430x175x265
Net Weight(KG)13
OriginMainland China
Is Smart DeviceYes
CertificationCE

10. User Tips

Based on general usage and product information, here are some tips for optimal performance:

  • For the best cutting results and to maximize the lifespan of your consumables, operate the machine at 220V if possible, especially when relying on the built-in air compressor.
  • Always allow the machine to cool down after continuous use, particularly when cutting thicker materials, to prevent overheating of the built-in compressor.
  • Regularly check and replace worn electrodes and nozzles. These are critical for maintaining cut quality and protecting the torch.
  • When cutting, aim for approximately 70% of the maximum rated thickness for sustained performance and to avoid premature wear.

No specific user reviews or Q&A content were provided for additional tips.

11. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.