HTOOL HT008, SL22

Contents

HTOOL RF Signal Generator User Manual

Models: HT008 (23.5MHz-6GHz) & SL22 (45MHz-22GHz)

Brand: HTOOL

1. Introduction

This manual provides detailed instructions for the HTOOL HT008 and SL22 RF Signal Generators. These devices are designed for generating stable and precise RF signals across a wide frequency range, suitable for various testing and development applications.

1.1 Product Overview

The HTOOL signal generators come in two main variants:

  • HT008: Features the MAX2871 chip, GD32F303 main control, and a 0.96-inch OLED screen. It supports USB to serial communication via a built-in CH340G chip.
  • SL22: Utilizes the LMX2820 chip, GD32F427 main control, and a larger 2.8-inch LCD screen. It also supports USB virtual serial port communication.
HTOOL HT008 and SL22 Signal Generators side-by-side
Figure 1: HTOOL HT008 (left) and SL22 (right) Signal Generators.

1.2 Package Contents

Please check the contents of your package against the list below. If any items are missing or damaged, contact your vendor.

HT008 Package:

  • 1x MAX2871 23.5-6000MHz Signal Source unit (HT008)
  • 1x Type-USB data connection cable
HT008 Signal Generator and USB cable
Figure 2: HT008 Signal Generator and included USB cable.

SL22 Package:

  • 1x SL22 Signal Generator
  • 1x Type-C Data Cable
  • 1x Stylus
  • 2x SMA male to male extension cables
  • 1x SMA female to female adapter
  • 1x N female to SMA male adapter
  • 1x BNC female to SMA male adapter
  • 1x SMA female to F female adapter
  • 1x SMA male to BNC male adapter
SL22 Signal Generator and its accessories including cables, adapters, and stylus
Figure 3: SL22 Signal Generator and its accessories.

2. Specifications

2.1 HT008 Specifications

FeatureDescription
Main ChipMAX2871
Main ControlGD32F303
Display0.96-inch OLED (90*160 resolution)
Frequency Range23.5MHz - 6000MHz (6GHz)
Frequency Resolution78Hz (for frequencies ≤ 4MHz)
Phase Noise-111dBc@3GHz: 100KHz
Output ChannelsDual Channel
Channel 1 Output Power-1dBm, -1dBm, 2dBm, 5dBm (selectable)
Channel 2 Output Power16-level attenuation, -15dBm to -25dBm
Operating ModesPoint Frequency, Sweep
Communication InterfaceBuilt-in USB serial port (CH340G)
Power SupplyUSB power, 5V 1A battery power
HT008 Signal Generator circuit board with components and connectors
Figure 4: Top view of the HT008 Signal Generator circuit board.

2.2 SL22 Specifications

FeatureDescription
Product ModelSL22
FunctionSignal Source, Spectrum Analyzer
Main ChipLMX2820
Main ControlGD32F427
Display2.8-inch LCD (240*320 resolution)
Frequency RangeCH1, CH2: 45MHz - 22GHz
Power RangeP0~P7: -16dBm~7dBm (8 levels)
Frequency Accuracy1KHz
Sweep Width45MHz - 22GHz
Sweep StepMin 1KHz, Max 22555MHz
Sweep Time1ms - 10s
Output SignalSine Wave
Output InterfaceSMA (external thread, internal hole)
Power InterfaceTYPE-C
Product Dimensions132*74*22mm
Product Weight200g
Power Supply5V, 2A or higher adapter power supply
Special FeatureMemory function for user settings
SL22 Signal Generator technical parameter table
Figure 5: SL22 Technical Parameters (as seen on product image).
SL22 Signal Generator front view with screen and buttons
Figure 6: SL22 Signal Generator front view.
SL22 Signal Generator side view showing Type-C port, ON/OFF switch, and dimensions
Figure 7: SL22 Signal Generator side view with dimensions.

3. Setup

3.1 Power Connection

Both HT008 and SL22 models are powered via a Type-C USB port. Connect the provided USB cable to the device and a compatible 5V, 2A or higher power adapter (not included) or a USB port on a computer.

  • HT008: Can also be powered by a 5V 1A battery power supply.
  • SL22: Requires a 5V, 2A or higher adapter for optimal performance.
HT008 Signal Generator connected to power via USB-C cable, displaying menu
Figure 8: HT008 connected to power, showing initial menu.

3.2 Driver Installation (for Serial Control)

For serial control functionality, a USB driver may be required. Connect the device to your computer and install the necessary drivers if prompted or if the device is not recognized. The HT008 uses a CH340G chip, and the SL22 uses a virtual serial port.

3.3 RF Output Connection

The devices feature SMA output interfaces (external thread, internal hole). Use appropriate SMA cables and adapters (some included with SL22) to connect the signal generator to your testing equipment.

HT008 Signal Generator side view showing SMA connectors
Figure 9: HT008 side view with SMA connectors.

4. Operation

The signal generators offer Point Frequency and Sweep modes. Navigation is typically done using the physical buttons (left, right, up, down, OK) or the touchscreen/stylus for the SL22 model.

4.1 General Navigation

Use the directional buttons to move the cursor on the screen and select menu options. The 'OK' button (or equivalent) confirms selections or enters sub-menus.

Screenshots of the signal generator's user interface showing various settings for point frequency, single sweep, cyclic sweep, and device settings
Figure 10: Example UI screens for frequency, sweep, and device settings.

4.2 Point Frequency Mode

In this mode, you can set a single, stable output frequency.

  1. Navigate to the "Point Frequency" mode on the device.
  2. Use the left/right buttons to move the cursor to the frequency setting.
  3. Use the up/down buttons to adjust the desired frequency value.
  4. For HT008, select CH1 or CH2. For SL22, click "Set Frequency" and input the value.
  5. Confirm the setting (e.g., press OK or "On" for SL22) to activate the output.
  6. Adjust output power as needed through the "Power" setting in the interface.

4.3 Sweep Mode

Sweep mode allows the generator to sweep through a range of frequencies.

  1. Navigate to the "Sweep" mode.
  2. Select either "Single Sweep" or "Cyclic Sweep" (SL22).
  3. Use the left/right buttons to move the cursor to adjust the "Start Frequency" and "End Frequency".
  4. Set the "Sweep Step" and "Single Step Time" (or "Sweep Time").
  5. Important: Ensure the Start Frequency is less than or equal to the End Frequency. Also, verify that the sweep time and step size are set to valid values to prevent malfunction. If these parameters are not set correctly, the sweep function will not operate. You may need to re-open the sweep function after correcting settings.
  6. Adjust output power as needed through the "Power" setting in the interface.

4.4 Dual Channel Output (HT008)

The HT008 offers two independent output channels:

  • Channel 1: Provides selectable output power levels of -1dBm, -1dBm, 2dBm, or 5dBm.
  • Channel 2: Offers 16-level attenuation, ranging from -15dBm to -25dBm.

4.5 Memory Function (SL22)

The SL22 model includes a memory function that allows it to recall user-set point frequencies or sweep settings. This means the device can start working immediately with your last configuration upon power-on.

4.6 Serial Control

Both models support USB serial port control for advanced operations and secondary development. Specific control commands are available for integration with external software or custom applications. Refer to the manufacturer's documentation or development resources for detailed command protocols.

5. Maintenance

5.1 General Care

  • Keep the device clean and free from dust. Use a soft, dry cloth for cleaning.
  • Avoid exposing the device to extreme temperatures, humidity, or direct sunlight.
  • Do not drop or subject the device to strong impacts.
  • Ensure proper ventilation. The SL22 model has ventilation holes on the side; do not obstruct them.
SL22 Signal Generator showing ventilation holes on the side
Figure 11: SL22 ventilation holes.

5.2 Storage

When not in use for extended periods, store the signal generator in a cool, dry place, preferably in its original packaging or a protective case.

6. Troubleshooting

6.1 No Power / Device Not Turning On

  • Ensure the USB cable is securely connected to both the device and the power source.
  • Verify that the power adapter meets the specified requirements (5V, 2A or higher for SL22; 5V 1A for HT008).
  • Try a different USB cable or power adapter.
  • For SL22, ensure the ON/OFF switch is in the 'ON' position.

6.2 No Signal Output

  • Check that the output frequency and power settings are correctly configured in the device's menu.
  • Ensure the SMA cables and connectors are properly attached and not damaged.
  • Verify that the device is in the correct operating mode (Point Frequency or Sweep).
  • If in Sweep mode, confirm that the start frequency, end frequency, and sweep time/step are set to valid values. If the start frequency is greater than the end frequency, or sweep time/step is invalid, the sweep will not operate.

6.3 Computer Not Recognizing Device (for Serial Control)

  • Ensure the correct USB serial port drivers are installed on your computer.
  • Try connecting to a different USB port on your computer.
  • Restart your computer and the signal generator.

7. User Tips

  • For precise frequency adjustments, utilize the fine-tuning options available in the menu.
  • When performing sweeps, always double-check your start and end frequencies, as well as the step size and time, to avoid unexpected behavior.
  • Consider using the serial control interface for automated testing or integration into larger systems, as it offers more granular control.
  • Keep the firmware updated to ensure optimal performance and access to new features. Check the manufacturer's website for updates.

8. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the vendor or manufacturer directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.