TKSTAR YS128

Contents

Hard-wired Car Charger YS128 Instruction Manual

For TKSTAR GPS Tracker & GPRS Locator Realtime Tracking Devices

1. Product Overview

The TKSTAR YS128 Hard-wired Car Charger is designed to provide a stable 5V DC power supply from a vehicle's 12-24V DC electrical system. It is primarily intended for use with TKSTAR GPS trackers and GPRS locators, ensuring continuous power for real-time tracking devices.

Product overview video demonstrating the charger's features and connections.

2. Package Contents

  • 1 x Hard-wired Car Charger (Model YS128)
Hard-wired car charger YS128 with input/output specifications visible on the label.

Front view of the YS128 car charger, showing the main unit, micro-USB output cable, and ring terminal input wires.

3. Setup and Installation

This charger is designed for permanent installation within a vehicle's electrical system. Professional installation is recommended.

  1. Identify Power Source: Locate a suitable 12-24V DC power source in your vehicle. This is typically the vehicle's battery or an accessory power line. Ensure the power source is capable of providing the necessary current.
  2. Connect Input Wires: The charger has two input wires with ring terminals:
    • Connect the RED wire (positive) to the vehicle's positive (+) terminal or a switched positive power source.
    • Connect the BLACK wire (negative) to the vehicle's negative (-) terminal or a suitable ground point.
    Ensure connections are secure and insulated to prevent short circuits.
  3. Connect Output Cable: Plug the micro-USB connector from the charger's output cable into the charging port of your TKSTAR GPS tracker or compatible device.
  4. Secure the Charger: Mount the charger unit in a safe, dry location away from excessive heat or moisture, ensuring it does not interfere with vehicle operation.
Back view of the car charger showing the red and black ring terminals for hardwiring.

Rear view of the charger highlighting the ring terminals for direct battery connection.

Angled view of the car charger showing both the micro-USB output and the ring terminal input.

Angled view illustrating the micro-USB output and the hard-wired input connections.

4. Operating Instructions

Once properly installed and connected to a power source, the YS128 car charger operates automatically. It converts the vehicle's 12-24V DC power to a stable 5V DC output, continuously supplying power to the connected device. No further user interaction is required for its basic operation.

5. Maintenance

The YS128 car charger is designed for low maintenance. To ensure optimal performance and longevity:

  • Periodically inspect all wiring connections to ensure they remain secure and free from corrosion.
  • Keep the charger unit clean and free from dust and debris.
  • Avoid exposing the charger to extreme temperatures or direct water contact.
  • Do not attempt to open or modify the charger unit, as this will void any potential warranty and may cause damage.

6. Troubleshooting

If you encounter issues with your YS128 car charger, refer to the following troubleshooting steps:

Problem Possible Cause Solution
Device not charging/receiving power.
  • Loose or incorrect wiring connections.
  • No power from vehicle's electrical system.
  • Faulty micro-USB cable or device.
  • Check that the red wire is connected to positive (+) and black to negative (-) securely.
  • Verify the vehicle's power source is active (e.g., ignition on for accessory power).
  • Test with a different micro-USB cable or device if possible.
Charger unit becomes hot or fails prematurely.
  • Overcurrent draw by the connected device.
  • Incorrect input voltage.
  • Internal fault.
  • Ensure the connected device requires 5V and draws no more than 1.5A.
  • Confirm vehicle input voltage is within 12-24V DC.
  • Discontinue use and contact customer support if issues persist.

7. Specifications

Feature Specification
Model Name YS128
Brand TKSTAR
Input Voltage DC 12-24V
Output Voltage DC 5V
Output Current 1.5A
PCB Included Yes
Origin Mainland China

8. User Tips

  • Power Compatibility: Always ensure the device you are connecting requires 5V and draws no more than 1.5A. Exceeding the current limit can damage the charger and the connected device.
  • Correct Polarity: Double-check the wiring polarity (red to positive, black to negative) before powering on the charger to prevent damage.
  • Secure Connections: Loose connections can lead to intermittent power supply or overheating. Ensure all connections are tight and properly insulated.

9. Warranty and Support

For warranty information or technical support, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.