LEFOO LFM53

Contents

LEFOO LFM53 Micro Differential Pressure Transmitter User Manual

High Accuracy Low Range Sensor

1. Introduction

The LEFOO LFM53 Micro Differential Pressure Transmitter is a high-accuracy, low-range sensor designed for precise measurement of differential pressure in various applications. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your device.

Front view of the LEFOO LFM53 Differential Pressure Transmitter
Figure 1: Front view of the LEFOO LFM53 Differential Pressure Transmitter, showing the display with 'MOD 0 Pa', two pressure ports, and a cable gland for electrical connection.

2. Safety Information

Please read and understand all safety instructions before installing or operating the device. Failure to follow these instructions may result in injury or damage to the equipment.

  • Ensure power is disconnected before any installation or maintenance procedures.
  • Only qualified personnel should perform installation and wiring.
  • Do not exceed the specified pressure or electrical ratings.
  • Protect the device from extreme temperatures, moisture, and corrosive environments.

3. Installation

3.1. Mounting

The LFM53 transmitter is designed for wall or panel mounting. Ensure the mounting surface is stable and free from vibrations. Use appropriate screws and anchors for secure installation.

3.2. Electrical Connection

The device requires a stable power supply. Refer to the wiring diagram for correct connections. The cable gland on the device is for securing and sealing the electrical cable.

Typical Wiring (Consult specific model documentation for exact details):

  • Power Supply: Connect the positive (+) and negative (-) terminals to the appropriate power source (e.g., 24V DC).
  • Output Signal: Connect the output terminals to your control system or display unit. The output type (e.g., 4-20mA, 0-10V) depends on the specific model variant.

3.3. Pressure Connection

The LFM53 features two pressure ports for differential pressure measurement. Connect the higher pressure source to the 'High' port and the lower pressure source to the 'Low' port. Ensure all connections are leak-free.

4. Operation

4.1. Powering On

Once installed and wired correctly, apply power to the device. The display will illuminate and show the current differential pressure reading, typically in Pascals (Pa).

4.2. Display Interpretation

The LCD display shows the measured differential pressure. Depending on the model or configuration, it may show 'MOD' (Mode) or 'ID' (Identification) along with the pressure value and unit (Pa).

4.3. Zeroing/Calibration

For optimal accuracy, it is recommended to perform a zero adjustment periodically or after installation. Consult your specific model's detailed instructions for the exact procedure, which usually involves applying zero differential pressure and pressing a calibration button or following a menu-driven process.

5. Maintenance

  • Cleaning: Keep the device clean and free from dust and debris. Use a soft, dry cloth for cleaning the exterior. Do not use abrasive cleaners or solvents.
  • Pressure Ports: Periodically check the pressure ports for blockages or damage. Ensure tubing connections are secure and free of leaks.
  • Electrical Connections: Verify that all electrical connections remain tight and free from corrosion.
  • Recalibration: Depending on the application and required accuracy, periodic recalibration by a qualified technician may be necessary.

6. Troubleshooting

ProblemPossible CauseSolution
No display/No powerNo power supply or incorrect wiring.Check power connections and ensure correct voltage. Verify wiring according to the diagram.
Incorrect pressure readingIncorrect zero adjustment, blocked pressure ports, or leaks in tubing.Perform zero adjustment. Check pressure ports and tubing for blockages or leaks. Ensure correct pressure port connections (High/Low).
Unstable readingVibrations, electrical interference, or unstable pressure source.Mount the device on a stable surface. Check for sources of electrical interference. Ensure the pressure source is stable.
Device not respondingInternal fault.Disconnect power, wait 30 seconds, then reconnect. If the problem persists, contact technical support.

7. Specifications

The LEFOO LFM53 series offers various models with different ranges and output types. Please refer to your specific model number for exact specifications.

ParameterValue/Description
Model NumberLFM53 (e.g., LFM531-O-A, LFM532-O-E, LFM533-O-E1)
Measurement TypeDifferential Pressure
AccuracyHigh Accuracy (specifics vary by model)
Pressure RangeLow Range (e.g., 0-100 Pa, 0-500 Pa, 0-1000 Pa)
Output SignalAnalog (e.g., 4-20mA, 0-10V) or Digital (model dependent)
Power SupplyTypically 24V DC (check product label)
Operating TemperatureStandard industrial range (e.g., -10°C to +60°C)
OriginMainland China

8. User Tips

  • For critical applications, consider using a redundant sensor or regular cross-checking with a calibrated reference.
  • When connecting tubing, ensure there are no kinks or sharp bends that could affect pressure transmission.
  • If measuring very low differential pressures, ensure the environment is free from drafts or sudden temperature changes that could cause fluctuations.
  • Always verify the specific model variant (e.g., LFM531-O-A, LFM532-O-E) to ensure compatibility with your system's requirements for range and output.

9. Warranty and Support

For warranty claims, technical support, or service inquiries, please contact the seller or authorized distributor from whom you purchased the LEFOO LFM53 Micro Differential Pressure Transmitter. Provide your product model number and purchase details for efficient assistance.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.