Lilytech ZL-7901A

Contents

ZL-7901A PID Multifunctional Automatic Intelligent Incubator Controller

Model: ZL-7901A | Brand: Lilytech

1. Introduction

The ZL-7901A is an advanced PID multifunctional automatic intelligent incubator controller designed for precise control of temperature and humidity in hatching environments. It features a large display, rich functionality, and flexible settings, making it suitable for high-level incubators. This manual provides detailed instructions for installation, operation, parameter configuration, and troubleshooting to ensure optimal performance of your incubator system.

ZL-7901A Incubator Controller with chick and egg
The ZL-7901A controller, designed for precise incubator management.
Video showcasing the ZL-7901A controller from various angles.

2. Features

The ZL-7901A controller offers a comprehensive set of features for efficient incubator management:

  • Temperature control: Relays up/down limit control, SSR PID control.
  • Humidity or dehumidify control.
  • Timer air exhaust control.
  • Timer egg turning control.
  • Illumination control.
  • Alarm output.
  • Auto restart function.
  • Temperature/humidity over limit warning and protection.
  • Temperature/humidity sensor fault warning and protection.
Key features of ZL-7901A controller
Visual representation of key features including air exchange, egg turning, illumination, and alarm functions.

3. Specifications

Below are the technical specifications for the ZL-7901A controller:

Parameter Value
Power Supply 100-240VAC, 50 or 60Hz
Main Heater Relay Output 7.5A / 1.0A (Resistive)
Aux Heater Relay Output 7.5A / 1.0A (Resistive)
Humidity Control Relay Output 7.5A / 1.0A (Resistive)
Lamp Control Relay Output 7.5A / 1.0A (Resistive)
Air Exhaust Control Relay Output 3A
Egg Turning Relay Output 1A
Alarm Output Relay 1A
SSR Driver Output 20mA/10VDC MAX
Temperature Sensor Input NTC temperature sensor, 5K/3470
Humidity Sensor Input ZL-SHr04J or ZL-SHr04P
Setting Range Humidity 0-99% RH (ZL-SHr04J is for 0-80%RH, ZL-SHr04P is for 0-99%RH)
Accuracy Temperature ±0.1°C
Accuracy Humidity ±3%RH (ZL-SHr04J), ±2%RH (ZL-SHr04P)
Working Environment -20~45°C, 10~90% RH without dew

Note: If 7.5A rated current is for tungsten lamp, do not exceed 1.0A. If drive is for 5V (for external voltage to DC12VDC), it is in fact an AC/DC, with huge surging when power supplied, the service lifetime is not guaranteed.

4. Setup & Installation

Proper installation is crucial for the safe and effective operation of the ZL-7901A controller. Please follow the wiring diagram carefully.

4.1 Wiring Diagram

ZL-7901A Wiring Diagram
Detailed wiring diagram for the ZL-7901A controller. Ensure all connections are made correctly and securely.

Wiring Instructions:

  • Power Input (L, N): Connect 100-240Vac input to terminals L and N.
  • Main Heater (R1): Connect the main heater to terminals 1 and 2.
  • Auxiliary Heater (R2): Connect the auxiliary heater to terminals 3 and 4.
  • Humidity Control (R3): Connect the humidity control device to terminals 5 and 6.
  • Illumination (R4): Connect the lamp to terminals 7 and 8.
  • Ventilation (R5): Connect the ventilation fan to terminals 9 and 10.
  • Egg Turning Motor (R6, R7): Connect the egg turning motor to terminals 11 and 12 (Left-turning) and 13 and 14 (Right-turning).
  • Alarm 1 & 2 (R8, R9): Connect alarm devices to terminals 15 and 16 (Alarm 1) and 17 and 18 (Alarm 2).
  • Temperature Sensor: Connect the temperature sensor to the designated terminals.
  • Humidity Sensor: Connect the humidity sensor to the designated terminals.
  • Limit Switches (SQ1, SQ2): Connect limit switches for the egg turning motor.
  • External Heater (SSR): Connect an external heater via an SSR (Solid State Relay) to the SSR output terminals.

Attention: Correct electrical wiring must be manipulated by certified electricians. Wrong wiring may damage the device and system seriously. Avoid installation in an environment with corrosive gases or strong electro-magnetic field. The device is possible abnormal in such condition.

4.2 Sensor Options

The ZL-7901A supports different humidity sensor options:

Humidity Sensor Options ZL-SHr04J and ZL-SHr04P
Two humidity sensor options: ZL-SHr04J (0-80%RH) and ZL-SHr04P (0-99%RH), with their respective wiring details.
  • ZL-SHr04J: Range 0-80%RH, Accuracy ±3%RH.
  • ZL-SHr04P: Range 0-99%RH, Accuracy ±2%RH.

Ensure the correct sensor is connected and configured according to your specific needs.

5. Operation

This section details the basic operation and key functions of the ZL-7901A controller.

5.1 Key Functions

Key Function Remark
Power Keep depressed for 3 seconds to turn on/offline
Set Short press to switch between humidity set and temperature set; Long press to set other parameters (see Parameter Table below)
Up Arrow (∧) Increase the set value. Keep depressed for fast set.
Down Arrow (∨) Decrease the set value. Keep depressed for fast set.
Enter Confirmation
Reset Short press to cancel and return.
Lamp Long press to clear incubating accumulated days counter.
Fn Turn the lamp off/on Combination key

5.2 Display Icons

ZL-7901A Display Icons
Page 1 of the manual showing the controller's display and key layout.
Icon Function On Off Blinking
Humidity/Dehumidity state Humidity/Dehumidity state Energized De-energized
Main heater Main heater Energized De-energized
Auxiliary heater Auxiliary heater Energized De-energized
Air exhaust Air exhaust Energized De-energized
Egg turning motor, turn right Egg turning motor, turn right Energized De-energized
Egg turning motor, turn left Egg turning motor, turn left Energized De-energized
Warning Warning – – Warning
E01 Temperature sensor fault Warning No warning
E02 Humidity sensor fault Warning No warning
tHI Temperature higher than up limit Warning No warning
tLO Temperature lower than down limit Warning No warning
hHI Humidity higher than up limit Warning No warning
hLO Humidity lower than down limit Warning No warning
UnL Restore to default parameters Restoring to default parameters

5.3 Key Operation

Fast Set Temperature (T11), Fast Set Humidity (H20):

  • Press Set to switch between temperature and humidity setting. Press ∧ and ∨ to set the value.
  • Press Enter to save the setting.
  • Press Reset or without key operation for 30 seconds, exit the mode, and the set value is not saved.

Parameters Setting:

  • Keep Set and ∨ depressed simultaneously for 3 seconds. LCD shows "Psd 000".
  • Press ∧ and ∨ to enter password "default 000". Press Enter to confirm.
  • The password is correct, enter into parameter setting mode. Press Exit.
  • Press Set to select parameter code. Press ∧ and ∨ to set the value. Press Enter to save the setting.
  • Press Reset or without key operation for 30 seconds, exit the mode, and the set value is not saved.

5.4 Fahrenheit/Celsius Display

Keep Fn and ∨ depressed simultaneously for 3 seconds to switch between Fahrenheit / Celsius display.

5.5 Incubation Day Counter

When controlling, the incubation day counter will keep counting. If the counter value reaches U18, controller keeps controlling as normal, and the counter value will be flashing. If the counter value reaches U18, stop counting. Keeping Lamp depressed for 3 seconds will reset the accumulated days of egg turning and incubation day counter.

5.6 Auto Restart Function

When the controller is offline, stop, and then comes back, the controller will run under the same settings before the power supply stops.

6. Parameter Settings

The ZL-7901A controller allows for detailed configuration of various parameters to suit different incubation needs. Refer to the tables below for a complete list of parameters and their functions.

6.1 Parameter Table (Temperature, Humidity, Egg Turning)

ZL-7901A Parameter Table Page 3
Page 3 of the manual, detailing parameters for temperature, humidity, and egg turning.
ZL-7901A Parameter Table Continued Page 4
Page 4 of the manual, continuing the parameter table with air exhaust, lamp, and alarm functions.

For detailed descriptions of each parameter (T10-T32, H10-H25, U10-U14, U20-U93), their ranges, units, indications, and default values, please refer to the images above or the full manual PDF.

6.2 PID Control Appendix

ZL-7901A PID Control Appendix Page 8
Page 8 of the manual, explaining PID control, auto tuning, hysteresis, and manual tuning principles.

The controller supports PID auto-tuning for optimal temperature control. This function (T10=2) allows the controller to automatically find suitable PID parameters (Kp/Ti/Td). If PV is not able to reach SP within reasonable time, increase heater power rate. If PV overshoot or fall below SP, auto tuning is not able to get the PID parameters correctly.

For more advanced PID tuning and hysteresis control details, consult the appendix in the full manual.

7. Maintenance

To ensure the longevity and accurate performance of your ZL-7901A controller, follow these general maintenance guidelines:

  • Keep the controller clean and free from dust and debris.
  • Ensure proper ventilation around the unit to prevent overheating.
  • Regularly check all wiring connections for tightness and signs of wear.
  • Avoid exposing the controller to extreme temperatures, humidity, or corrosive environments.
  • If the device is to be stored for an extended period, disconnect it from power and store it in a dry, cool place.

For any issues, refer to the troubleshooting section or contact support.

8. Troubleshooting

This section provides guidance for common issues and warning messages displayed by the ZL-7901A controller.

8.1 Warning Control Instruction

ZL-7901A Warning Control Instruction Table Page 6
Page 6 of the manual, detailing warning control instructions and actions.
No. Code Remark Real time detection Delay Duration Reset Action
1 E01 Temperature sensor fault Yes 0s 0s Auto Alarming, temperature output off, the other control not affected
2 E02 Humidity sensor fault Yes 0s 0s Auto Alarming, humidity output off, the other control not affected
3 tHI Over high temperature warning point Yes 0s 0s Auto Alarming
4 tLO Lower than low temperature warning point Yes 0s 0s Auto Alarming
5 hHI Over high humidity warning point Yes 0s 0s Auto Alarming
6 hLO Lower than low humidity warning point Yes 0s 0s Auto Alarming
7 tCE Touched IC fault Yes 0s 0s Auto Alarming

When there is error of sensors, high/low limit temperature or humidity warning, there will be buzzing warning. Any key press can stop the warning.

9. User Tips

  • Temperature and Humidity Control: The ZL-7901A controller is designed to control both humidity and temperature, making it a versatile solution for various incubation needs.
  • Wiring Safety: Always ensure that wiring is performed by a certified electrician to prevent damage to the device or system.
  • Environment: Avoid installing the controller in areas with corrosive gases or strong electromagnetic fields to ensure stable operation.

10. Warranty & Support

This product has been strictly tested before shipping. The company warranty is one year. The responsibility is limited to the sale of this product itself. Damage caused by improper usage is not covered by the warranty.

For further assistance or technical support, please refer to the official Lilytech website or contact your vendor.

The full manual PDF can be downloaded from: www.suzhoulily.com/pdf/ZL-7901A_en_V2.6d.pdf

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.