1. Introduction
Thank you for choosing the ANDELI TIG-250 Pro 6-in-1 AC DC TIG Welder. This advanced welding machine is designed for versatility and precision, offering AC DC TIG, AC DC Pulse, MMA, Cold Welding, and Lift TIG functions. Featuring an intuitive LCD smart display and robust IGBT inverter technology, it is suitable for a wide range of materials including aluminum, carbon steel, and stainless steel. This manual provides essential information for safe and effective operation, maintenance, and troubleshooting.
2. Safety Precautions
WARNING: Welding can be dangerous. Always follow safety guidelines to prevent injury or death.
- Always wear appropriate personal protective equipment (PPE), including a welding helmet with proper shade, flame-resistant clothing, welding gloves, and safety shoes.
- Ensure adequate ventilation in the work area to avoid inhaling welding fumes.
- Protect bystanders from arc rays and sparks using welding screens or barriers.
- Never touch live electrical parts. Ensure the machine is properly grounded.
- Keep flammable materials away from the welding area.
- Do not operate the welder in damp or wet conditions.
- Disconnect power before performing any maintenance or adjustments.
- Read and understand all instructions in this manual before operating the machine.
3. Package Contents
Please check the package to ensure all items are present and undamaged:
- 1 x ANDELI TIG-250 Pro Welder Unit
- 1 x Ground Clamp (2M)
- 1 x TIG Torch WP-26 (4M)
- 1 x Gas Pipe (3M)
- 2 x Hose Clamps
- 20 x Collets
- 20 x Nozzles
- 30 x Tungsten Electrodes
- 2 x Foot Pedals
- 1 x Pyrex Cup Kit (49 pieces)
- 1 x TIG Torch WP-9F (4M)

4. Specifications
The following table details the technical specifications of the TIG-250 Pro AC/DC Welder:
| Feature | Specification |
|---|---|
| Model | TIG-250 Pro AC/DC |
| Rated Input Voltage | 110V / 220V (Auto-sensing) |
| Frequency | 50/60Hz |
| Max. Load Power Capacity | 30 kVA |
| Rated Input Current (A) | TIG: 37A (220V), 17A (110V); MMA: 45A (220V), 10A (110V) |
| Welding Current Range | 10-200A |
| Rated Duty Cycle @40°C (TIG) | 60% (200A/18V), 100% (110A/13.6V) |
| Rated Output Voltage | 24 V |
| Output Polarity | AC/DC TIG |
| Arc-Starting Current (A) | 10-200 |
| Pre-Gas Time (S) | 0-1 |
| Up-Slope Time (S) | 0-5 |
| Peak Current (A) | 10-200 |
| Pulse Frequency (Hz) | 0.5-100 |
| Pulse Width (%) | 5-100 |
| Base Current (A) | 10-200 |
| Down-Slope Time (S) | 0-5 |
| Crater-Filling Current (A) | 10-200 |
| Post-Gas Time (S) | 0-10 |
| AC Frequency (Hz) | 40-100 |
| Clean Pulse Width (AC Balance) | 20-50 |
| AC Waveforms | Square wave |
| Cold Welding Time (MS) | 1-200 |
| Cold Welding Interval (Hz) | 0-10 |
| Welding Thickness (MM) | Aluminum: 0.5-5mm, Cold Welding: 0.3-1mm, TIG: 0.8-8mm |
| 2T/4T Function | Yes |
| Welding Material | Stainless Steel, Carbon Steel, Aluminum, Titanium |
| Remote Control | Yes |
| Gas Check | Yes |
| Protection Class | IP21S |
| Insulation Class | H |
| Cooling | AIR |
| Dimension (MM) | 485x210x340 |
| Net Weight (KG) | 12.5 |

5. Setup
Before operating the welder, ensure proper setup:
- Power Connection: Connect the welder to a suitable 110V or 220V power supply. The machine automatically detects the voltage. Ensure the power outlet can handle the maximum rated input current.
- Ground Clamp Connection: Attach the ground clamp securely to the workpiece or welding table. A good ground connection is crucial for safe and effective welding.
- TIG Torch Connection: Connect the TIG torch to the appropriate port on the front panel. Ensure all connections are tight.
- Gas Connection: Connect the gas pipe from your shielding gas cylinder (e.g., Argon for TIG welding) to the gas inlet on the welder. Use the provided hose clamps to secure the connection.
- Tungsten Electrode Installation: Insert the tungsten electrode into the collet of the TIG torch. Ensure the electrode is sharpened to the correct angle for your application.
- Foot Pedal Connection (Optional): If using a foot pedal for current control, connect it to the designated port.

6. Operating Modes
The TIG-250 Pro offers multiple welding modes, selectable via the LCD smart display:
- AC TIG Welding: Ideal for aluminum and magnesium alloys. Allows for cleaning action to remove oxides.
- DC TIG Welding: Suitable for stainless steel, carbon steel, copper, and other non-ferrous metals (except aluminum). Provides deep penetration.
- AC Pulse TIG Welding: Offers enhanced control over heat input, reducing distortion and improving weld quality, especially on thin materials.
- DC Pulse TIG Welding: Similar to AC Pulse, but for DC-compatible materials. Improves arc stability and penetration.
- Cold Welding: A specialized mode for welding extremely thin sheets without overheating or discoloration. Welding thickness: 0.3-1mm.
- MMA (Stick) Welding: For general-purpose welding with coated electrodes. Supports 3.2 welding rods for easy arcing on various materials.
- Lift TIG: Provides a stable arc start without high-frequency interference.


7. Controls and Display
The TIG-250 Pro features a high-definition LCD display and intuitive controls for precise parameter adjustment.
- LCD Display: Provides clear visualization of welding parameters, including waveform selection, pulse ON/OFF, pre/post gas settings, start/stop current, 2T/4T selection, and balance.
- Control Knobs: Use the left (L-KNOB) and right (R-KNOB) knobs to navigate menus and adjust values.
- Mode Selection: Easily switch between HF TIG AC, HF TIG DC, Lift TIG DC, Cold Weld, and other modes directly from the LCD panel.
- Synergy Support: The machine supports synergy functions, making it suitable for beginners by simplifying parameter settings.
- Channel Storage: The welder allows for storing and recalling up to 6 welding parameter channels for quick setup of frequently used settings.


8. Maintenance
Regular maintenance ensures the longevity and optimal performance of your welder.
- Cleaning: Periodically clean the exterior of the machine with a dry cloth. Use compressed air to blow out dust and debris from the cooling vents.
- Torch and Cable Inspection: Regularly inspect the TIG torch, ground clamp, and all cables for signs of wear, damage, or loose connections. Replace damaged components immediately.
- Tungsten Electrode Care: Ensure tungsten electrodes are clean and properly sharpened. Replace worn or contaminated electrodes.
- Gas System Check: Verify that gas hoses are free from leaks and connections are secure.
- Cooling System: The TIG-250 Pro features a complete cooling system. Ensure the cooling vents are not obstructed to maintain steady power output and prevent overheating.

9. Troubleshooting
Here are some common issues and their potential solutions:
- No Arc:
- Check power supply and connections.
- Ensure ground clamp is securely attached to the workpiece.
- Verify gas flow and pressure.
- Inspect tungsten electrode for proper installation and condition.
- Check welding parameters on the LCD display.
- Poor Weld Quality:
- Adjust welding current, voltage, and gas flow.
- Ensure proper tungsten electrode type and preparation.
- Clean the workpiece thoroughly before welding.
- Check for proper AC balance settings (for aluminum).
- Verify pre/post gas times are adequate to prevent oxidation.
- Overheating Indication:
- Ensure the cooling vents are clear and unobstructed.
- Reduce duty cycle or allow the machine to cool down.
- Check ambient temperature.
- Machine Not Turning On:
- Verify power cable connection and power switch position.
- Check circuit breaker or fuse.
10. User Tips
- For welding aluminum, ensure the AC balance is correctly set to achieve a clean weld bead and prevent oxidation. The 'Balance' feature on the LCD helps achieve this.
- Utilize the 'PRE/POST GAS' function to protect the weld puddle from atmospheric contamination, especially important for reactive metals like aluminum.
- When welding thin materials, experiment with the 'Cold Welding' mode and adjustable cold-time to prevent burn-through and minimize distortion. Longer cold-time generally results in a darker weld color.
- Take advantage of the 6-channel storage feature to save your preferred settings for different materials or applications, allowing for quick recall and consistent results.
- For beginners, the synergy support on the LCD can help in setting initial parameters, providing a good starting point for various welding tasks.


11. Warranty and Support
The ANDELI TIG-250 Pro Welder comes with a two-year warranty and free replacement parts. For any issues or technical assistance, please contact our customer service team. We are committed to providing free guidance and support.
For further information or assistance, please refer to the official ANDELI website or contact your local distributor.