Hormann 40.685MHz Remote Control User Manual

1. Introduction

This manual provides detailed instructions for the setup, operation, and maintenance of your new Hormann 40.685MHz fixed code remote control. This remote is designed to replace specific original Hormann remote controls for electric telescopic doors, road gates, and alarm systems.

2. Specifications

3. Compatibility

This remote control is specifically designed to be a perfect replacement for original Hormann 40.685MHz grey button remote controls. It is crucial to verify your existing remote's frequency and button color for proper compatibility.

Compatible Models:

• HORMANN 40.685MHz Grey buttons
• HORMANN HS4
• HORMANN HSM4
• HORMANN HS2
• HORMANN HSM2
• HORMANN HSE2
• HORMANN HSE4

Important Compatibility Notes:

• This remote control is not compatible with other brands or models of remote controls.
• Even if your remote control operates on 40.685 MHz, if it is not a grey button Hormann model listed above, it may not be compatible.
• It is not applicable to HORMANN BS series remotes.

4. Setup: Cloning Instructions

The remote control uses a face-to-face cloning method. Follow these steps carefully to program your new remote:

1. Prepare the Original Remote: Press and hold a button on your original Hormann remote control.
2. Initiate Cloning on New Remote: Simultaneously press and hold a corresponding button on your new clone remote control.
3. Position Remotes: Bring both remote controls very close to each other, ideally touching or within a few millimeters.
4. Observe Indicator Light: Continue holding both buttons. The indicator light on the new remote control will flash rapidly, indicating successful programming. This process typically takes about 3 seconds.
5. Verify: Release the buttons. Test the newly programmed button on your new remote control.
6. Program Additional Buttons: Repeat steps 1-5 for any other buttons you wish to program on your new remote control.

Video Guide: Cloning Process

5. Operating the Remote Control

Once successfully cloned, your new remote control operates identically to your original Hormann remote. Simply press the programmed button to activate your garage door, gate, or alarm system.

• Range: The wireless transmission distance is typically 10-150 meters in open space. Environmental factors and obstacles may affect this range.
• Indicator Light: A brief flash of the indicator light confirms that a signal is being transmitted when a button is pressed.

6. Maintenance

Battery Replacement

The remote control is powered by a 12V 23A battery. If the remote's range decreases significantly or the indicator light does not illuminate when a button is pressed, it may be time to replace the battery.

1. Locate the battery compartment on the back of the remote control.
2. Carefully open the compartment using a small screwdriver or coin if necessary.
3. Remove the old 12V 23A battery.
4. Insert a new 12V 23A battery, ensuring correct polarity (+/-).
5. Close the battery compartment securely.

7. Troubleshooting

• Remote not cloning:
  • Ensure both remotes are very close during the cloning process.
  • Make sure you are pressing and holding the buttons simultaneously for the required duration (approx. 3 seconds).
  • Verify that your original remote is a compatible Hormann 40.685MHz grey button model.
  • Check the battery in both the original and new remote controls.
• New remote not working after cloning:
  • Re-attempt the cloning process, ensuring the indicator light flashes rapidly to confirm success.
  • Confirm that the correct button on the new remote was programmed for the desired function.
  • Ensure the new remote's battery is fresh and correctly installed.
• Reduced operating range:
  • Replace the battery in the new remote control.
  • Ensure there are no new obstructions between the remote and the receiver.
  • Extreme weather conditions can sometimes affect wireless performance.

8. User Tips

• For best cloning results, perform the process in a quiet area away from other radio interference.
• Always keep your original remote control in a safe place, even after cloning, as it may be needed for future programming or as a backup.
• The compact size of this remote makes it easy to attach to a keychain without occupying much space.

9. Warranty and Support

This product is manufactured by Shenzhen Scimagic Development Technology Co.Ltd.

Certifications:

The product holds CE and RoHS certifications, indicating compliance with European safety, health, and environmental protection standards.

Manufacturer Address:

For further assistance or inquiries, please refer to the official product page or contact the seller directly.

A PDF version of the user manual is available for download from the product's listing page.