DOOYA DM35R 10/17

Contents

Dooya DM35R 10/17 Tubular Motor User Manual

Model: DM35R 10/17

Brand: DOOYA

1. Introduction

The Dooya DM35R 10/17 Tubular Motor is designed for motorizing various types of rolling blinds and roller shutters. It features a built-in 433MHz RF receiver, allowing for convenient control via a compatible Dooya remote controller. This manual provides essential information for the safe installation, operation, and maintenance of your tubular motor.

2. Safety Information

  • This product is intended for indoor use only.
  • Ensure the power supply matches the motor's rated voltage (AC 220V/230V, 50/60Hz).
  • Installation and wiring should be performed by a qualified electrician in accordance with local electrical codes.
  • Keep children and pets away from motorized blinds during operation.
  • Do not operate the motor if any part is damaged or malfunctioning.
  • This product complies with EU directives: Low Voltage Directive 2014/35/EU (LVD), Electromagnetic Compatibility Directive 2014/30/EU (EMC), Restriction of Hazardous Substances Directive 2011/65/EU (RoHS), and General Product Safety Regulation (GPSR).

3. Package Contents

Please check the package for the following items:

  • Dooya DM35R 10/17 Tubular Motor
  • Crown and Drive Adapter (specific type depends on your tube selection)
  • Antenna
  • Mounting Screws and Accessories
Dooya DM35R 10/17 Tubular Motor and accessories
Figure 1: Tubular Motor and Included Accessories

4. Specifications

FeatureSpecification
Model NumberDM35R 10/17 (also known as DM35RL 10/17)
Communication MethodRF (Radio Frequency)
Working Voltage220V/230V 50/60Hz
Rated Torque10 N.m
Rated Speed17 r/min
Rated Power121 W
Rated Current0.53 A
Capacitor4 μF / 450 V
Running TimeS2 4min
Protection DegreeIP44
Insulation ClassH
Max Load24 kg
Tube Diameter Compatibility35mm (motor diameter), compatible with 40mm Round, 45mm Groove, 47mm Groove, 50mm Round, 50mm Groove, 40mm Octagonal tubes (with appropriate adapters)
Compatible RemoteDooya 433MHz Rolling Code Remote Controller (e.g., DC2700, DC2702, DC2760)
OriginMainland China
Technical Data Table and Wiring Diagram for Dooya DM35R Motor
Figure 2: Detailed Technical Data and Wiring Diagram
Various tube types compatible with the motor
Figure 3: Compatible Tube Types

5. Installation

Before installation, ensure you have the correct crown and drive adapter for your specific roller blind tube. The motor is suitable for 35mm diameter tubes and can be adapted for 40mm Round, 45mm Groove, 47mm Groove, 50mm Round, 50mm Groove, and 40mm Octagonal tubes.

5.1 Mechanical Installation

  1. Mount the brackets securely to the wall or ceiling, ensuring they are level and correctly spaced for your roller blind.
  2. Attach the crown and drive adapter to the motor.
  3. Insert the motor with the attached crown and drive adapter into the roller blind tube.
  4. Place the assembled roller blind tube with the motor into the mounted brackets.
Exploded view of motorized roller blind components
Figure 4: Solution for Motorized Roller Blinds (Components)

5.2 Electrical Wiring

The motor requires a 220V/230V AC power supply. Connect the wires as follows:

  • Brown Wire: Live (L)
  • Blue Wire: Neutral (N)
  • Yellow/Green Wire: Earth (Ground)

Ensure all connections are secure and insulated. Refer to the wiring diagram for detailed connections.

Close-up of motor wiring (brown, blue, yellow/green)
Figure 5: Motor Wiring Details

5.3 Installation Video Guide

For a visual guide on installation and programming, please watch the following video:

Video 1: Dooya Tubular Motor Installation and Programming Guide. This video demonstrates mounting, remote pairing, and setting upper and lower limits for the roller blind.

6. Operation

The DM35R 10/17 motor operates with a Dooya 433MHz rolling code remote controller. Ensure your remote is a rolling code version to match the motor.

Various Dooya 433MHz remote controllers
Figure 6: Compatible Dooya Remote Controllers (e.g., DC2700AC, DC2760AC, DC2702)

6.1 Remote Control Pairing

To pair your remote control with the motor:

  1. Locate the programming button on the motor (often a small button near the wiring).
  2. Press the programming button on the motor briefly. The motor may jog slightly.
  3. Within a few seconds, press the 'Up' button on your remote control. The motor should jog again, indicating successful pairing.

6.2 Setting Upper and Lower Limits

The motor's travel limits define how far the blind will open and close. These are typically set using the remote control.

  1. Set Lower Limit: Use the 'Down' button to move the blind to your desired lowest position. Press the 'Stop' button to halt. Then, press and hold the 'Stop' button until the motor jogs, confirming the lower limit is set.
  2. Set Upper Limit: Use the 'Up' button to move the blind to your desired highest position. Press the 'Stop' button to halt. Then, press and hold the 'Stop' button until the motor jogs, confirming the upper limit is set.

Refer to the installation video (Video 1) for a visual demonstration of these steps.

6.3 Basic Control

  • Up Button: Moves the blind upwards.
  • Down Button: Moves the blind downwards.
  • Stop Button: Stops the blind at its current position.

7. Maintenance

  • Regularly inspect the motor and blind for any signs of wear or damage.
  • Keep the motor and remote control clean and free from dust and moisture.
  • Do not attempt to lubricate the motor or internal components.
  • If the motor requires service, contact qualified personnel.

8. Troubleshooting

  • Motor not responding to remote:
    • Check if the remote control batteries are dead and replace them if necessary.
    • Ensure the remote is paired correctly with the motor (refer to Section 6.1).
    • Verify there are no obstructions blocking the RF signal.
  • Blind not moving to correct upper/lower limits:
    • Re-program the upper and lower limits (refer to Section 6.2).
    • Check for any physical obstructions preventing the blind from reaching its full travel.
  • Motor makes unusual noises:
    • Immediately stop operation.
    • Inspect the blind and motor for any loose parts or obstructions.
    • If the noise persists, contact customer support.
  • Motor does not operate at all:
    • Check the power supply connection and ensure the motor is receiving power.
    • Verify that the wiring is correct (refer to Section 5.2).

9. User Tips

  • When selecting the motor, ensure you specify the type of tube you have (e.g., 40mm round, 50mm grooved) so the correct crown and driving adapters can be provided.
  • Always test the motor's operation and limit settings immediately after installation to prevent damage to the blind or motor.
  • Keep your remote control in an easily accessible but safe place to avoid accidental operation.

10. Warranty and Support

For detailed warranty information and technical support, please refer to the official user manual PDF available from the seller. The manufacturer is Lumi United Technology Co., Ltd., located at 8th Floor, JinQi Wisdom Valley, No.1 Tangling Road, Liuxian Ave, Taoyuan Residential District, Nanshan District, Shenzhen, China. The EU Authorized Representative is Sophie Bennett, 9 rue du Bat d'Argent, 69001 Lyon, France.

This product complies with EU RoHS regulations. Please dispose of it responsibly according to local waste electrical and electronic equipment regulations, and do not treat it as household waste.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.