ANDELI CUT-60 PRO

Contents

ANDELI CUT-60 PRO Plasma Cutting Machine

Model: CUT-60 PRO

1. Introduction

Thank you for choosing the ANDELI CUT-60 PRO Plasma Cutting Machine. This professional-grade plasma cutter is designed for efficient and precise metal cutting, featuring non-HF pilot arc technology and multi-voltage compatibility. This manual provides essential information for the safe and effective setup, operation, and maintenance of your new equipment. Please read it thoroughly before use.

Safety Information

Always observe general safety precautions when operating welding and cutting equipment. Ensure proper ventilation, wear appropriate personal protective equipment (PPE) including welding helmet, gloves, and protective clothing. Keep a fire extinguisher nearby. Do not operate in wet conditions or near flammable materials.

2. Setup

2.1 Unpacking and Contents

Carefully unpack your ANDELI CUT-60 PRO and verify that all components are present. The package should include:

ANDELI CUT-60 PRO Plasma Cutter with included accessories and dimensions
Figure 2.1: ANDELI CUT-60 PRO Plasma Cutter and Accessories
  • Ground Clamp (2M)
  • Cutting Torch (6M)
  • Gas Pipe (3M)
  • Oil-water Separator
  • Electrode (10 pieces)
  • Tip (10 pieces)
  • Teflon Tape

2.2 Power Connection

The CUT-60 PRO is a dual-voltage machine (220V/380V or 220V/400V compatible). It does not come with a power plug, requiring direct wiring according to the voltage used. Ensure the wiring is performed by a qualified electrician to match your power supply.

Wiring diagram for 1-phase 220V, 3-phase 220V, and 3-phase 400V connections
Figure 2.2: Dual Voltage Wiring Diagram

Refer to the diagram for correct wiring:

  • 1PH AC220V: Connect Blue and Black wires.
  • 3PH AC220V: Connect Blue, Black, and Brown wires.
  • 3PH AC400V: Connect Blue, Black, and Brown wires.

2.3 Air Compressor Connection

Connect a suitable air compressor to the machine. The required air pressure for optimal operation is between 0.3 and 0.6 MPa. Ensure the oil-water separator is installed to provide clean, dry air to the plasma cutter.

2.4 Torch Assembly

Assemble the cutting torch components as shown in the diagram. Ensure all parts are securely fitted.

Diagram showing the components of the plasma cutting torch: Cutting Torch Body, Diffuser, Electrode, Tip, Outside Nozzle, Spacer
Figure 2.3: Cutting Torch Components

2.5 Ground Clamp Connection

Attach the ground clamp securely to the workpiece. A good ground connection is crucial for safe and effective cutting.

3. Operating Instructions

3.1 Control Panel Overview

The ANDELI CUT-60 PRO features an intuitive LCD display for easy parameter adjustment.

LCD Panel display showing 2T/4T mode, brightness settings, current (50A for 220V, 60A for 380V), and post flow settings
Figure 3.1: LCD Control Panel
  • 2T/4T Mode: Select between 2-touch (press and hold for arc) and 4-touch (press once to start, once to stop) trigger modes.
  • Brightness: Adjust display brightness.
  • Current Adjustment: Use the knob to set the cutting current (e.g., 50A for 220V, 60A for 380V). The current changes automatically based on plate thickness.
  • Post Flow: Adjust the gas post-flow time (e.g., 0.5S for 220V, 3.0S for 380V). This cools the torch and extends consumable life.

3.2 Cutting Process

The CUT-60 PRO utilizes a non-touch pilot arc for reliable and clean cuts.

Features of the plasma cutter: Non-touch Pilot Arc, Non-high frequency, Multi-voltage compatible
Figure 3.2: Key Features
  • Non-touch Pilot Arc: This feature allows for arc initiation without direct contact with the workpiece, making it ideal for cutting rough, rusty, dirty, greasy, or painted materials and extending consumable life.
  • Non-High Frequency: The reliable plasma arc initiation without high frequency significantly reduces electromagnetic interference.
  • Multi-Voltage Compatible: Supports single-phase 220V (240V), three-phase 220V, and three-phase 380V (400V) power supply environments.

3.3 Cutting Thickness Guidelines

The machine offers impressive cutting capabilities depending on the input voltage.

Cutting thickness demonstration: 30mm limit cutting at 220V and 35mm limit cutting at 380V
Figure 3.3: Cutting Thickness Capabilities
  • 220V Operation: Maximum cut thickness up to 35mm, with an effective cutting thickness of 30mm.
  • 380V Operation: Maximum cut thickness up to 40mm, with an effective cutting thickness of 35mm.

For specific materials, refer to the specifications table in Section 6.

3.4 CNC Compatibility

The CUT-60 PRO is equipped with 2-core and 4-core CNC interfaces, making it compatible with CNC cutting equipment for automated and precise cutting operations.

Plasma cutter connected to CNC equipment for automated cutting
Figure 3.4: CNC Equipment Integration

4. Maintenance

Regular maintenance ensures the longevity and optimal performance of your plasma cutter.

  • Cleanliness: Keep the machine clean and free from dust and debris. Regularly clean the air vents to prevent overheating.
  • Consumables: Inspect the torch consumables (electrode, tip, diffuser, outside nozzle, spacer) regularly. Replace them when they show signs of wear to maintain cut quality and extend torch life.
  • Air System: Periodically drain the oil-water separator and ensure it is functioning correctly to provide clean, dry air.
  • Connections: Check all electrical and air connections for tightness and integrity.

5. Troubleshooting

If you encounter issues with your plasma cutter, perform these basic checks before seeking professional assistance:

  • No Power: Ensure the machine is correctly wired and connected to a live power source. Check circuit breakers.
  • No Arc: Verify the ground clamp is securely attached to the workpiece. Check torch consumables for wear or damage. Ensure adequate air pressure.
  • Poor Cut Quality: Replace worn consumables. Adjust cutting speed and current settings. Ensure proper air pressure and clean, dry air supply.
  • Overheating: Ensure the machine has proper ventilation and the cooling fan is operating. Allow the machine to cool down if the thermal overload indicator is active.
  • Air Flow Issues: Check air compressor operation, hose connections, and the oil-water separator.

6. Specifications

Parameter220V (1PH/3PH)400V (3PH)
ModelLCD CNC CUT-60 PRO
Input Voltage (V)220V ±10%400V ±10%
Rated Input Current (A)4211
Rated Input Capacity (kVA)9.67.5
Non-load Voltage (V)365320
Current Range (A)20-5020-60
Rated Output Voltage (V)88-10088-104
Efficiency (%)8586
Power Factor0.630.99
30% Duty Cycle (40℃, 10min)5060
60% Duty Cycle (40℃, 10min)3542
100% Duty Cycle (40℃, 10min)2733
Cutting Thickness (Max)
Carbon Steel30 MM35 MM
Stainless Steel20 MM25 MM
Copper10 MM14 MM
Aluminium15 MM20 MM
Pressure of Air Compressor (MPa)0.3-0.6
Nozzle Inside Hole (MM)1.1
Insulation ClassH
Protection ClassIP21S
Arcing WayNON-TOUCH
Grid CutYES
Machine Dimensions (MM)460*224*327
Weight (KG)13.5

7. User Tips

  • Voltage Selection: Always ensure the machine is correctly wired for your specific power supply (220V or 380V/400V) before turning it on. Incorrect voltage can damage the unit.
  • Consumable Life: The non-touch pilot arc feature helps extend consumable life, but regular inspection and timely replacement of electrodes and tips are still crucial for optimal performance.
  • Cutting Rough Surfaces: Leverage the non-touch pilot arc for cutting through painted, rusty, or otherwise imperfect surfaces without needing to clean them first.
  • Air Quality: Maintain a clean and dry air supply by regularly checking and draining the oil-water separator. Moisture in the air line can negatively impact cut quality and consumable life.
  • CNC Integration: If using with CNC equipment, ensure proper connection via the 2-core or 4-core interface and configure your CNC software accordingly for automated cutting.

8. Frequently Asked Questions (FAQ)

Q: What is the maximum cutting thickness of the CUT-60 PRO?
A: The maximum cutting thickness is 35mm for 220V operation and 40mm for 380V operation. Effective cutting thicknesses are 30mm (220V) and 35mm (380V).
Q: Is this plasma cutter compatible with CNC machines?
A: Yes, the CUT-60 PRO is equipped with both 2-core and 4-core CNC interfaces, making it compatible with various CNC systems.
Q: What does 'Non-touch Pilot Arc' mean?
A: Non-touch Pilot Arc means the arc starts without the torch tip needing to touch the workpiece. This is beneficial for cutting rusty, painted, or uneven surfaces and helps prolong consumable life.
Q: What air pressure is required for operation?
A: The machine requires an air compressor capable of supplying between 0.3 and 0.6 MPa (approximately 43.5 to 87 PSI) of pressure.

9. Warranty and Support

9.1 Warranty Information

The ANDELI CUT-60 PRO Plasma Cutting Machine comes with a 2-year warranty from the date of purchase, covering manufacturing defects and malfunctions under normal use. Please retain your proof of purchase for warranty claims.

9.2 Technical Support

For technical assistance, troubleshooting beyond this manual, or warranty service, please contact your authorized ANDELI dealer or the manufacturer's customer support. OEM customized support is also available.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.