Flytec V700-10/V700-11

Contents

Flytec V700 Bait Boat Circuit Board Set Instruction Manual

Models: V700-10 (Boat Circuit Board), V700-11 (Remote Control Circuit Board Assembly)

1. Product Overview

This manual provides instructions for the installation, operation, and maintenance of the Flytec V700 Bait Boat Circuit Board Set. This set includes both the receiving circuit board for the bait boat (V700-10) and the transmitting circuit board assembly for the remote control (V700-11).

Flytec V700 Circuit Board Set
Figure 1: Flytec V700 Circuit Board Set (Boat Receiving Board and Remote Control Transmitting Board)

2. Safety Information

  • This product is recommended for users aged 14 years and older.
  • Ensure all power sources are disconnected before installation or maintenance to prevent electrical shock.
  • Handle circuit boards with care to avoid damage from static electricity or physical impact.
  • Batteries are not included. Use appropriate batteries as specified for your bait boat and remote control.

3. Installation Guide

3.1. Boat Circuit Board (V700-10) Installation

The V700-10 is the receiving board for the bait boat. Carefully connect all components to the designated ports as shown in the diagram below.

V700 Boat Circuit Board Wiring Diagram
Figure 2: V700 Boat Circuit Board (V700-10) with labeled connection points.

Connection Points:

  • F LED: Front Light
  • R LED: Right Light Strip
  • L LED: Left Light Strip
  • K1: Switch
  • Battery: Main Battery Connection
  • RM: Right Motor
  • LM: Left Motor
  • PRM: Right Solenoid Valve
  • PLM: Left Solenoid Valve
  • Battery Indicator: For battery status display.
  • ANT: Antenna connection.

3.2. Remote Control Circuit Board (V700-11) Installation

The V700-11 is the transmitting board assembly for the remote control. Install it within the remote control casing, ensuring all controls and the LCD screen are properly connected.

V700 Remote Control Circuit Board Assembly
Figure 3: V700 Remote Control Circuit Board Assembly (V700-11) with LCD screen and connecting cable.

4. Operation

4.1. Frequency Pairing

After installing both circuit boards, they must be paired to establish communication. Follow these steps:

  1. Ensure both the remote control and the bait boat are powered on.
  2. If the boat is not responding, you need to re-pair the frequency.
  3. On the remote control, long press the left trim button.
  4. While holding the left trim button, turn on the power of the boat.
  5. Then, turn on the power of the remote control.
  6. The remote control will emit a long beep sound.
  7. Frequency pairing is successful when the red indicator light of the remote control is always on, the LCD screen flashes, the light of the boat switch button is always on, and the turning light is always on.
Frequency Pairing Instructions
Figure 4: Visual representation of pairing instructions.

4.2. Remote Control Features

The remote control features an LED screen for displaying information and offers a remote control distance of up to 500 meters. The bait boat is equipped with cool night lights and indicator lights for turning (right/left).

Video 1: Demonstration of Flytec V700 Bait Boat features, including night lights, turning indicators, and remote control display.

5. Maintenance

  • The bait boat features a full waterproof cover. Ensure it is properly sealed after any access to internal components to maintain water resistance.
  • Propellers are equipped with covers. Regularly check and clean the propellers and their covers to prevent debris accumulation and ensure smooth operation.
  • Keep circuit boards clean and dry. Avoid exposure to moisture, dust, and extreme temperatures.
  • Periodically inspect all wiring connections for looseness or damage.

6. Troubleshooting

  • Boat not responding to remote control: Refer to Section 4.1 "Frequency Pairing" to re-pair the devices.
  • Lights or motors not functioning: Check all wiring connections on the boat circuit board (Figure 2) to ensure they are secure. Verify battery charge levels for both the boat and remote control.
  • Remote control display not working: Ensure the remote control circuit board assembly (V700-11) is correctly installed and connected, and that the remote control has sufficient power.

7. Specifications

FeatureSpecification
Brand NameFlytec
Model NumbersV700-10 (Boat Circuit Board), V700-11 (Remote Control Circuit Board Assembly)
MaterialComposite Material
For Vehicle TypeBoats
RC Parts & AccsReceivers
Remote Control Peripherals/DevicesReceivers
Tool SuppliesSticker (for installation/labeling)
Recommend Age14+ years
UseVehicles & Remote Control Toys
CertificationCE
Is ElectricNo Battery (refers to the product itself not containing batteries)
Is Batteries IncludedNo
Boat Circuit Board (V700-10) Size7.5 x 7 x 1.4 cm
Boat Circuit Board (V700-10) Weight24g
Remote Control Circuit Board (V700-11) Size13 x 6.5 x 2.2 cm (Circuit Board), 6 x 3.8 x 0.7 cm (Display Screen)
Remote Control Circuit Board (V700-11) Weight52.5g
Remote Control DistanceUp to 500 meters

8. User Tips

  • Always perform the frequency pairing procedure carefully to ensure stable communication between the remote control and the bait boat.
  • Before each use, check all connections and ensure the waterproof cover of the boat is securely fastened.
  • Keep spare batteries for both the boat and remote control to avoid interruptions during use.

9. Warranty and Support

For warranty information, technical support, or replacement parts, please contact the seller or the official Flytec customer service directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.