ETENWOLF ZEPHYR V3

Contents

ETENWOLF ZEPHYR V3 Portable Air Compressor User Manual

Model: ZEPHYR V3

Introduction

Thank you for choosing the ETENWOLF ZEPHYR V3 Portable Air Compressor. This manual provides essential information for the safe and efficient operation of your device. Designed to inflate a wide range of tires and inflatables, this portable power station pump enhances versatility for your outdoor adventures. Please read all instructions and safety warnings before use.

Warning! Please read all safety warnings and all instructions to reduce the risk of electric shock, fire, and/or serious injury.

Package Content

The following items are included in your ETENWOLF ZEPHYR V3 package:

  • ETENWOLF ZEPHYR V3 Air Compressor x 1
  • 15W Charger x 1
  • USB A to C Charging Cable x 1
  • Cone Shaped Blowing Nozzle x 1
  • Ball Needle x 1
  • French Copper Adapter x 1
  • T-shaped Quick Connector x 1
  • User Manual x 1
ETENWOLF ZEPHYR V3 Package Content
Image: Contents of the ETENWOLF ZEPHYR V3 package, including the compressor, various nozzles, and cables.

Product Overview

The ETENWOLF ZEPHYR V3 is a compact and powerful portable air compressor designed for various inflation needs. It features a digital display, multiple operating modes, and a built-in power bank function.

ETENWOLF ZEPHYR V3 Main Features
Image: Overview of the ETENWOLF ZEPHYR V3, highlighting its 160 PSI max pressure, 22L/Min inflation speed, and 7800mAh battery capacity, shown inflating a car tire with various accessories.

Component Identification

Refer to the diagram below for the location of each component:

ETENWOLF ZEPHYR V3 Component Diagram
Image: Diagram of the ETENWOLF ZEPHYR V3 showing its various parts and their functions, including the display, buttons, and ports.
  1. Light button
  2. Mode button (Switchable Units)
  3. "+" increase pressure button
  4. Start/pause power button
  5. Center display
  6. "-" decrease pressure button
  7. LED work light
  8. Type-C port (Input)
  9. USB-A port (Output)
  10. Pressure hose
  11. Presta valve adapter
  12. Inflation needle
  13. High-pressure tapered nozzle
  14. Manual mode
  15. Car mode
  16. Bicycle mode
  17. Ball mode
  18. Pressure unit
  19. Target input value
  20. Actual pressure value
  21. Safety alert symbol
  22. Battery level indicator

Quick Start Guide (Setup)

Follow these steps for initial setup and inflation:

  1. Remove Pressure Hose: Remove the pressure hose (10) from its storage channel.
  2. Connect Nozzle: Insert the nozzle (10) clockwise into the object being inflated.
  3. Activate Device: Press the Start/pause power button (04) to activate the machine.
  4. Select Mode: Press the Mode button (02) to switch among the four different modes: Manual mode (14), Car mode (15), Bicycle mode (16), and Ball mode (17).
  5. Select Pressure Unit: Select the pressure unit (PSI, KPa, or Bar) by pressing the Mode button (02) for more than 1 second.
  6. Adjust Target Pressure: Press the "-" button (06) to decrease or the "+" button (03) to increase the target pressure value.
  7. Start Inflation: Press the Start/pause power button (04) again to start inflation.
  8. Automatic Shut-off: When the inflated item reaches the preset value, the unit will turn off automatically.
ETENWOLF ZEPHYR V3 Easy to Use Steps
Image: Visual guide showing four steps for easy use: 1. Remove valve cap and connect, 2. Long press three second startup, 3. Press M to select the mode, 4. Press start inflating. Also shows product dimensions and hose length.

Included Attachments

A Presta valve adapter (11), an inflation needle (12), and a high-pressure tapered nozzle (13) are located on the back side storage panel for convenient access.

ETENWOLF ZEPHYR V3 Nozzle Storage
Image: Close-up of the ETENWOLF ZEPHYR V3 showing the integrated storage for various nozzles and adapters.

Operating Instructions

Mode Button (02)

  • Short press to switch between four inflation modes: Manual, Car, Bicycle, and Ball.
  • Long press (more than 1 second) to select the pressure unit (PSI, KPa, or Bar).

Start/Pause Power Button (04)

  • Turn On: Long-press for two seconds to turn on the inflator.
  • Turn Off: When the inflator is on, long-press for two seconds to turn it off.
  • Pause: During inflation, press the button again to pause the machine.

Automatic Shut-off Conditions

The inflator will automatically turn off in the following cases:

  • After 3 minutes of inactivity.
  • If the charging cable is accidentally disconnected during charging.
  • After 5 minutes of inactivity after being fully charged.
  • After 5 minutes of inactivity after being used as a power bank.
  • If inflating for over 5 minutes, but the actual pressure is still below 5 PSI.
  • If inflating for over 5 minutes, but the actual pressure is above 150 PSI.

Preset Pressure Values

The display shows the target input value (19) in smaller font at the top and the actual pressure value (20) of the inflated device in larger font at the bottom.

ModeAdjustable Pressure RangeDefault Pressure
Manual mode3-160 PSI30 PSI
Car mode8-130 PSI35 PSI
Bicycle mode10-145 PSI22 PSI
Ball mode3-16 PSI8.5 PSI

Note: The system remembers the last pressure settings. Double-check the target input value to prevent over-inflation. After inflation, tire pressure may decrease by 0.5-1.5 PSI as the temperature normalizes. When pumping a bike tire, quickly remove the hose to avoid air loss.

LED Work Light (07)

The LED work light (07) is located at the front of the inflator. To turn it on, first power on the machine by pressing the Start/pause power button (04), then press the LIGHT button (01).

The light has four different modes:

  • Bright flashlight
  • Ultra-bright flash light
  • Slow strobe light
  • SOS light

Note: The light automatically turns off after 1 hour. After the first auto shut-off, you can manually turn it on again. If manually turned on a second time, it will not automatically turn off and must be turned off manually.

ETENWOLF ZEPHYR V3 LED Light Function
Image: The ETENWOLF ZEPHYR V3 showing its adjustable LED light, illuminating work in the dark.

Power Bank Function

The ETENWOLF ZEPHYR V3 can also function as a power bank to charge your electronic devices such as phones, tablets, laptops, drones, and cameras. It provides USB-A Output 5V 2A, 10W.

Note:

  • The inflator needs to be powered on to work as a power bank.
  • After 3 minutes of charging, the display panel will only show the battery level to save power.
  • The inflator will automatically turn off after 2 minutes of fully charging the connected devices.
ETENWOLF ZEPHYR V3 Power Bank Feature
Image: The ETENWOLF ZEPHYR V3 being used as a power bank to charge a phone, demonstrating its USB port.

Battery Charging & Indicator

Charging with AC Power Supply

For optimal charging performance and stability, use a 5V 3A 15W PD charger to charge the built-in battery. Full charging from 0% to 100% takes approximately 2-3 hours.

Battery Level Indicator (22)

The battery level indicator (22) is displayed by four bars, with each bar representing 25% of the total capacity.

Note:

  • The inflator will automatically shut off after 2 minutes of inactivity once fully charged.
  • The inflator cannot be used while it is charging.

Pressure Recalibration

Different altitudes can cause variations of 1-3 PSI in pressure readings. In high-altitude areas (especially above 5000 ft/1524 meters), you can recalibrate the pump's pressure sensor.

Recalibration Steps:

  1. Power on the pump (04).
  2. Hold the Light button (01) and Mode button (02) for 10 seconds.
  3. When the entire screen flickers, recalibration is complete.

Note:

  • Power off the pump before calibration.
  • The Pressure hose (10) should not be connected to any item. Any item providing pressure to the hose will disable the recalibration process.
  • A charged battery or other power source is required for recalibration.
  • There is no memory for new recalibration settings. Once the power is turned off, it will reset to sea level calibration (altitude 0 ft/meters).

Troubleshooting

ProblemSolution
Slow inflation speed
  • Check whether the item being inflated is leaking.
  • Check whether the air nozzle connection is tightened.
  • Check whether the inflation hoses are broken.
  • Check whether the ventilation slots are blocked.
Air compressor turns on, but does not inflateCheck whether the pressure of the item being inflated exceeds the preset pressure.
Unable to increase or decrease the preset pressure
  • Make sure the correct mode is chosen, and the preset value does not exceed the range.
  • Select the manual mode and adjust the preset value within the pressure range of 3-160 PSI.
The inflator inflates but the pressure shown on the display is zero.If the air pressure is under 3 PSI, the pressure displayed will show zero due to the pump's minimum pressure range.
The battery level indicator does not show on the screen after charging.Use a certified charger or standard charger, and the included charging cable, and try to charge it.
There is an air leakage when connecting the high-pressure air hose.Tighten the air nozzle.
Unable to charge other devices
  • Check whether the battery is sufficient.
  • Verify if the charging device is compatible with the output 5V 3A.
  • It cannot be used as a power source while it is being charged.
  • Use the original charging cable provided with the charging device for charging.
Safety alert symbol light on display shows the E08 error codeAfter shutting down and restarting, if the issue persists, send the device for factory repair.
Display shows the E10 error codeMotor malfunction warning. If the issue persists after restarting, send for factory repair.
Display shows the E11 error codeLow-temperature charging protection. Restore temperature to above 0°C before continuing charging.
Display shows the E12 error codeHigh-temperature charging protection. Restore temperature to below 45°C before continuing charging.
Display shows the E13 error codeLow-temperature discharge protection. Restore temperature to above -20°C before continuing operation.
Display shows the E14 error codeHigh-temperature discharge protection. Restore temperature to below 58°C before continuing operation.
Display shows the E15 error codeAir pump exceeded working time. Check for leaks in the inflated item.
Display shows the E16 error codeOverpressure protection. Returns to normal after pressure release.
Display shows the E17 error codeHigh-pressure operation exceeded working time. Check if the inflated item is functioning abnormally.
Display shows the E18 error codeBattery damage warning. Device will shut down. Send for factory repair.

Specifications

FeatureDetail
ModelZephyr V3 Air Compressor
Dimensions128*102*180 mm (5.04*4.02*7.09 inches)
Item Weight1.2kg
Inflation Pressure Range3-160 PSI / 0.2-11 Bar
Operating Temperature (Charging)0°C-45°C / 32°F-113°F
Operating Temperature (Discharging)-20°C-74°C / -4°F-165°F
Storage Temperature-10°C-60°C / 14°F-140°F
High Pressure Air Tube Length0.9 meters (90cm)
Battery Capacity7800mAh
Working NoiseLower than 85dB within 1 meter
Input (Type-C)5V 3A
Output (USB-A)5V 2A
Charging Time2-3 hours
Continuous Working TimeApproximately 25 minutes at a pressure range of 20-50 PSI, in a 25°C ambient temperature, under full charge.
Sensor Accuracy±1 PSI
ETENWOLF ZEPHYR V3 Comparison
Image: Comparison chart highlighting the advantages of ETENWOLF V3 in terms of battery capacity (7800mAh), inflation speed (<1 minute for ordinary car tire), continuous inflation without burning, long standby time (idle for a year without power loss), ten-year battery life, and hands-free practicality.

Safety Instructions

  1. This product is not a toy and should not be used by children. Users must be above 16 years old. Keep a safe distance between children and the inflator while inflating. The product contains a built-in lithium battery. Do not place the product into fire or dispose of the battery improperly.
  2. Overheating damage or water ingress may increase the risk of fire or explosion. Keep the product away from heat sources and do not leave it in a hot car for prolonged periods. If the inflator becomes very hot, there is a risk of explosion.
  3. Store the product within temperatures ranging from -10°C to 60°C (14°F to 140°F). Extreme temperatures can damage the battery and shorten the inflator's lifespan. Long-term storage may decrease battery effectiveness. Charge the inflator at least once every three months to maintain performance.
  4. The product has a built-in DC motor that may generate sparks during operation. Do not use it in environments with dust or gas that are liable to explode.
  5. If there is an unusual noise or the temperature becomes very high during inflation, turn off the inflator immediately.
  6. Before setting the inflation pressure value, ensure the pressure unit is correctly selected. Mixing up PSI and Bar could lead to dangerous overinflation.
  7. Unit conversion: 1 Bar = 14.5 PSI; 1 Bar = 100 KPa.
  8. Do not leave the pump unattended while it is in operation.
  9. Use the product in a dry and clean environment. Intrusion of sand and dust can cause damage. Do not wash the product with water.
  10. Make sure to use certified PD chargers and the included charging cable to charge this product. Malfunction caused by not following these requirements is not covered by the warranty.
  11. To reduce the risk of electric shock, do not expose to rain. Store indoors.

User Tips

  • Deflation: While the primary function is inflation, you can manually release air from tires or inflatables by pressing the valve stem without the inflator connected. The device itself does not have a dedicated deflation function.
  • Pre-set Pressure: Always set your desired pressure before starting inflation to ensure accuracy and prevent over-inflation.
  • Cooling: Allow the inflator to cool down if it becomes hot during prolonged use, especially when inflating multiple large tires.

Warranty & Support

2-Year Coverage

Within two years of purchase, ETENWOLF provides timely and effective online after-sale service. We will repair or replace any defective product (due to manufacturing fault) within this warranty period.

Contact Support

For any after-sales inquiries, please contact us at: support@etenwolf.com

We are committed to providing you with professional and efficient service!

ETENWOLF Certifications
Image: Various certification documents for the ETENWOLF product, indicating compliance with quality and safety standards.

Product Demonstration Video

Watch this video for a visual guide on how to use the ETENWOLF ZEPHYR V3 Portable Air Compressor and its features:

Video: A demonstration of the ETENWOLF ZEPHYR V3 in action, showing its compact size, ease of use for car, bike, and ball inflation, digital display, cooling system, power bank function, and included attachments.
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.