CYCPLUS M3 GPS Bicycle Computer User Manual

1. Introduction and Overview

The CYCPLUS M3 is a smart GPS bike computer designed to enhance your cycling experience by providing precise data and easy connectivity. It features a large 2.8-inch display for clear data visibility, fast 10-second GPS positioning, and an impressive 100-hour working time on a single charge. The M3 supports BLE 5.0 and ANT+ protocols, allowing seamless connection with various cycling sensors and quick data synchronization to your mobile phone via the CYCPLUS Fit APP.

Front view of the CYCPLUS M3 GPS Bike Computer.

2. Package Contents

Please check the package to ensure all items are present:

• GPS Bike Computer (M3)
• Bike Computer Mount
• Rubber Pad
• Rubber Band x 3
• Type-C Charging Cable
• User Manual (this document)

All items included in the CYCPLUS M3 package.

3. Specifications

Key features of the CYCPLUS M3 GPS Bike Computer.

4. Setup and Installation

Follow these steps to install your CYCPLUS M3 GPS Bike Computer:

1. Using the included rubber bands, securely attach the bike computer mount to your handlebar or stem by crossing the bands diagonally.
2. Once the mount base is secure, fix the M3 GPS Bike Computer onto the base by twisting it into place until it clicks.

An optional CYCPLUS Z1/Z3 bike mount (sold separately) can also be used for installation.

Installation diagram for the CYCPLUS M3 bike computer mount.

5. Button Functions

The CYCPLUS M3 features three buttons: L (Left), R1 (Right Top), and R2 (Right Bottom). Their functions vary depending on whether they are pressed short or long, and whether you are in normal use or settings mode.

The CYCPLUS M3 with its 2.8-inch display.

Normal Use Button Functions:

6. Data Display

The M3 device has 4 customizable data pages, which can be accessed by short pressing the R1 button. The upper section of the screen displays fixed data fields, while the lower section shows customizable fields.

Fixed Data Fields (Upper Section):

• Clock: Displays current time. Time zone can be set in settings.
• Recording Status:
  • No symbol: No trip recording in progress.
  • ►: Trip recording is active.
  • II: Trip recording is paused.
  • Flashing II: Auto-pause is active when stopped; recording resumes automatically upon movement.
• GPS:
  • : No GPS signal.
  • : GPS is working properly.
• Phone Connection: : Indicates device is connected to phone.
• Temperature: Displays current temperature (°C or °F, configurable in settings).
• Speed Sensor: : Indicates connection to a speed sensor; speed data comes from the sensor.
• Modes:
  • No symbol: Real-time speed and gradient.
  • AVG: Average speed and gradient.
  • MAX: Maximum speed and gradient.
• Speed Unit: KMH or MPH, configurable in settings. Affects distance and elevation display.

Customizable Data Fields (Lower Section):

These fields can be customized using the CYCPLUS Fit app.

• TIME: Riding Time
• DST: Riding Distance (meters/feet below 1km/0.1 miles, otherwise km/miles)
• ODO: Odograph
• SPD: Speed (unit matches setting)
• HR: Heart rate (requires heart rate monitor)
• PWR: Power (requires power meter)
• CAD: Cadence (requires cadence sensor)
• ALT: Elevation (always in meters)
• AST: Elevation Gain (meters/feet, switches to km/miles after 9999)
• DES: Elevation Loss (meters/feet, switches to km/miles after 9999)
• AVG: Indicates average data for the field.
• MAX: Indicates maximum data for the field.

Customizable data fields on the M3 display.

7. Settings

You can quickly set up your M3 by connecting it to the CYCPLUS Fit app. Alternatively, use the device buttons:

• Long press the R1 button to enter settings.
• Short press the R1 button to cycle through the 8 setting pages (C2 to C9).
• Long press the R1 button again to return to the home page after finishing.

ANT+ Sensors Connection (C2)

Press the L button to start searching for ANT+ sensors. The device will search for speed, heart rate, power, and cadence sensors. Detected sensor data will be displayed; a horizontal line appears if no sensor is found.

Wheel Circumference Setting (C3)

Press L to start. Use R1 to adjust the value. Use R2 to switch between digits. Press L to confirm and save.

Time Zone Setting (C4)

Press L to start. Use R1 to adjust the time zone. Use R2 to switch to minute digits, then R1 to adjust. Press L to confirm and save.

Speed Unit Setting (C5)

Press L to start. Use R1 to switch between KMH and MPH. Press L to confirm and save.

Temperature Unit Setting (C6)

Press L to start. Use R1 to switch between °C and °F. Press L to confirm and save.

Factory Reset (C7)

Press L to start. Long press R2 to restore factory settings. The device will power off after reset.

Odograph Setting (C8)

Press L to start. Use R1 to adjust the value. Use R2 to switch between digits. Press L to confirm and save.

Unpair Sensors (C9)

Go to the C9 page. Press the L button to unpair all connected sensors.

8. APP Connection

Download and use the CYCPLUS Fit APP for convenient device management and additional services. Search for "CYCPLUS Fit" on Google Play or the App Store, or scan the QR codes below:

For iOS

For Android

Scan to download the CYCPLUS Fit App.

Features of the CYCPLUS Fit App.

9. Operating Instructions

GPS Location - Quick Start Guide

For accurate satellite signal reception, ensure your device is in an open, unobstructed area and remains static. For faster GPS fix, connect to the CYCPLUS Fit app and download ephemeris data before riding.

1. Power On: Long press the L button.
2. GPS Signal Acquisition: After startup, it may take a few minutes to acquire a GPS signal. The symbol will appear when the device is ready.
3. Start Recording: Press the L button again. The ► symbol will appear when recording starts.
4. Save Recorded Data: Long press the R2 button. The 'SAVE' message will blink for 4 seconds. Once the ► or II icon disappears, the recording is successfully saved.
5. Power Off: Long press the L button.

Fast GPS positioning in approximately 10 seconds.

Additional Notes:

• Data Recording: If the device is shut down directly without manually saving, the current record will be automatically saved.
• Memory: When the memory is full, the device will automatically overwrite the oldest records in chronological order.
• Backlight: After setting the time zone, the screen backlight will automatically turn on from 18:00 to 09:00 daily. When any button is pressed, the backlight will turn on and turn off after 10 seconds.

10. User Tips

• Customize Your Display: Use the CYCPLUS Fit app to customize the data content and location for each page on your M3, tailoring it to your specific needs.
• Sensor Connectivity: The M3 supports BLE 5.0 and ANT+ protocols, allowing connection to various sensors like heart rate monitors, cadence sensors, and power meters for comprehensive data tracking.
• Data Sync: Easily transmit your cycling data to the CYCPLUS Fit App and Strava for analysis and sharing.
• Time Accuracy: If you experience issues with the device not saving the correct time, ensure your time zone settings are correctly configured both on the device (C4 setting) and within the CYCPLUS Fit app, and verify successful synchronization.
• Language Settings: For language options, check the settings within the CYCPLUS Fit app, as the device itself may not have direct language configuration.

11. Troubleshooting

• Incorrect Time Display: If the device shows the wrong time or fails to save the correct time after setting (C4), ensure your time zone is accurately set. Connect the device to the CYCPLUS Fit app and allow it to synchronize time data. If the issue persists, try a factory reset (C7) and reconfigure.
• No GPS Signal: Ensure you are in an open area with a clear view of the sky. Remain static for a few minutes during initial acquisition. For faster fixes, connect to the CYCPLUS Fit app and download ephemeris data.
• Sensor Not Connecting: Verify that your sensors are powered on and within range. Go to the ANT+ Sensors Connection (C2) setting on the M3 and initiate a search. If a sensor is not found, check its battery and try again.
• Data Not Syncing to App/Strava: Ensure your M3 is connected to the CYCPLUS Fit app via BLE 5.0. Check your internet connection on your phone. Within the app, verify that Strava integration is correctly set up and authorized.

12. Maintenance

• Cleaning: Wipe the device with a soft, damp cloth. Do not use abrasive cleaners or solvents.
• Water Resistance: The M3 is IPX6 water-resistant, meaning it can withstand splashes and rain. Do not submerge the device in water.
• Charging: Use the provided Type-C charging cable. Ensure the charging port is dry before connecting the cable.
• Storage: Store the device in a cool, dry place away from direct sunlight and extreme temperatures.

The M3 features IPX6 waterproofing and auto backlight.

13. Warranty and Support

Manufacturer: Chengdu Chendian Intelligent Technology Co., Ltd.

Address: No. 88 Tianchen Road, Chengdu, Sichuan Province, China.

Warranty: The product comes with a 2-year warranty for non-user-induced damage, offering free repair or replacement.

Contact: For support or warranty claims, please contact steven@cycplus.com.

For further details, you may refer to the official user manual PDF: CYCPLUS M3 User Manual (PDF)

14. Tire Circumference Chart

Use this chart as a reference for setting your wheel circumference. Tire circumference may vary slightly depending on tire pressure.