Yadea YADEA Controller

Contents

YADEA Controller User Manual

Model: YADEA Controller Series

Introduction

This manual provides essential information for the safe and efficient use of your YADEA Controller. These controllers are designed for various YADEA electric scooters and e-bikes, managing motor functions, speed regulation, and braking. Please read this manual thoroughly before installation and operation to ensure proper functionality and safety.

Setup and Installation

Proper installation is crucial for the performance and safety of your YADEA Controller. If you are unsure about any steps, it is recommended to seek professional assistance.

Safety Precautions

  • Ensure the vehicle is powered off and the battery is disconnected before beginning installation.
  • Wear appropriate safety gear, including gloves and eye protection.
  • Avoid touching live wires or components.
  • Verify all connections are secure and correctly polarized.

Installation Steps (General Guidance)

  1. Identify Components: Locate the controller mounting area, motor, battery, throttle, brake levers, and any display units.
  2. Mount the Controller: Secure the controller in a protected area, away from direct water exposure and excessive vibration. Ensure adequate ventilation.
  3. Wiring Connections:
    • Motor Wires: Connect the motor phase wires (typically thick wires) and Hall sensor wires (thinner wires) to the corresponding ports on the controller. Match colors carefully.
    • Battery Wires: Connect the main positive (+) and negative (-) battery wires to the controller's power input. Double-check polarity.
    • Throttle: Connect the throttle signal wire, power, and ground wires.
    • Brake Levers: Connect the brake signal wires. These typically cut motor power when activated.
    • Display/Instrument: Connect the instrument panel wires for speed display, battery level, and other functions.
    • Other Accessories: Connect any additional accessories such as lights or horn, ensuring they are compatible with the controller's output.
  4. Secure Connections: Ensure all connectors are fully seated and secured. Use cable ties to manage wires and prevent them from snagging or rubbing.
  5. Initial Power-Up: After all connections are made, reconnect the battery. Power on the vehicle and perform a low-speed test in a safe environment to verify basic functionality.
YADEA KS2-UL Controller with connected wires
Figure 1: YADEA KS2-UL Controller showing various connected wires, illustrating typical wiring points.

Operating Instructions

Once installed, your YADEA Controller facilitates the operation of your electric vehicle.

Basic Operation

  • Power On/Off: Use the vehicle's main power switch or key to turn the system on or off. The controller will initialize upon power-up.
  • Speed Control: The throttle (twist grip or thumb lever) controls the motor's speed. Apply gently to accelerate and release to decelerate.
  • Braking: Activating the brake levers will cut power to the motor and engage the vehicle's brakes. Some controllers also support electronic braking, which provides regenerative braking or additional stopping power.
  • Gear Selection: If your vehicle features a multi-gear system (e.g., 3rd gear stepless speed regulation as per specifications), use the designated switch or button to cycle through speed modes.
  • Instrument Display: The Hall/crystal instrument (if equipped) will show real-time information such as speed, battery level, and possibly error codes.

Maintenance

Regular maintenance helps prolong the life of your controller and ensures reliable performance.

  • Keep Clean and Dry: Periodically clean the exterior of the controller with a dry, soft cloth. Avoid using water or harsh chemicals. Ensure the controller remains dry and protected from moisture.
  • Inspect Connections: Regularly check all wiring connections for tightness and signs of corrosion or damage. Loose connections can lead to intermittent operation or component failure.
  • Avoid Extreme Conditions: Do not expose the controller to extreme temperatures (hot or cold) or direct sunlight for extended periods.
  • Cable Management: Ensure all cables are properly routed and secured to prevent wear and tear from vibration or rubbing.
  • Firmware Updates: If applicable, consult your vehicle manufacturer for information on controller firmware updates.

Troubleshooting

If you encounter issues with your YADEA Controller, refer to the following common problems and solutions.

Common Issues

  • No Power to Motor:
    • Check battery charge level.
    • Verify all power connections from the battery to the controller are secure.
    • Inspect the main power switch or key switch for damage.
  • Motor Not Responding to Throttle:
    • Check throttle connections.
    • Ensure brake levers are not engaged, as they typically cut motor power.
    • Verify Hall sensor wires are correctly connected.
  • Erratic Motor Behavior or Intermittent Power:
    • Inspect all wiring for loose connections, corrosion, or damage.
    • Check for any error codes displayed on the instrument panel.
    • Ensure the controller is not overheating.
  • Vehicle Not Reaching Full Speed:
    • Check the selected gear/speed mode.
    • Verify battery voltage is within the rated range.
    • Ensure the motor is functioning correctly.

If the problem persists after checking these points, it is recommended to contact a qualified technician or the manufacturer for further diagnosis and repair.

Specifications

The YADEA Controller series includes various models, each with specific characteristics. Below are detailed specifications for some common models.

Rear view of YADEA X1-CE Controller with label
Figure 2: Rear view of a YADEA X1-CE Controller, displaying its model, software version, rated voltage, low voltage protection, max current, and functional specifications.
YADEA Controller Model Specifications
FeatureX1-CE ControllerKS2-UL Controller
ModelX1-CEKS2-UL
Software VersionX12000107KS2-3
Rated VoltageDC48VDC36V
Low Voltage Protection42.5±0.5VDC30±0.5V
Max Current17A17A
Functions
  • Brushless DC motor vector control (FOC)
  • Hall/crystal instrument
  • 3rd gear stepless speed regulation
  • Variable throttle and electronic brakes
  • Brake tail light function
  • Brushless DC motor vector control (FOC)
  • Hall/crystal instrument
  • 3rd gear stepless speed regulation
  • Variable throttle and electronic brakes
  • Brake tail light function
Internal view of YADEA X1-CE Controller circuit board
Figure 3: Internal view of a YADEA X1-CE Controller circuit board, showing power terminals and various electronic components.

User Tips

  • Verify Compatibility: Always ensure the controller model you purchase is compatible with your specific YADEA electric scooter or e-bike model (e.g., KS6 Pro, KS5, X1). Check voltage and current ratings carefully.
  • Professional Installation: For optimal performance and safety, consider professional installation, especially if you are unfamiliar with electrical wiring.

Warranty and Support

For warranty information, technical support, or service inquiries, please contact your original seller or the YADEA customer service department. Keep your purchase receipt and product serial number handy for faster service.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.