DykbRadio IP2363-CHG-30W

Contents

IP2363 30W Auto Boost/Buck PD Fast Charging Module

Model: IP2363-CHG-30W | Brand: DykbRadio

1. Product Overview

The IP2363 30W Automatic Buck-Boost PD Fast Charging Module is a compact and efficient charger designed for 2S-5S Li-ion (NMC/NCA) or LiFePO4 battery packs. It supports 5-20V input from PD/QC power supplies or direct DC sources, and automatically adjusts (buck/boost) to charge the battery at up to 30W. The module features a toggle switch for battery cell count configuration, LED status indicators, and comprehensive protection features. Each module is pre-tested for reliable performance.

Key Features:

  • 30W Max Power: Requires 20V input for full output.
  • Wide Input Range: 5-20V (PD/QC/DC).
  • Battery Support: 2S-5S Li-ion / LiFePO4.
  • Auto Buck-Boost: Steps up or down voltage as needed.
  • Toggle Switch: Easy cell count configuration.
  • LED Status: Charging / Full / Fault indication.
  • Smart Protection: Overvoltage Protection (OVP), timeout, reverse polarity.
  • Compact Size: 4.6 x 3.8 cm.
Top-down view of the IP2363 charging module

Figure 1: Top-down view of the IP2363 charging module, showing the USB-C port, inductor, capacitors, and terminal blocks.

2. Safety & Warnings

Read all instructions before use to ensure safety and prevent damage.

DANGER: LITHIUM BATTERY SAFETY - Risk of fire or explosion.

Lithium batteries can be dangerous if mishandled. Use only with 2S-5S Li-ion or LiFePO4 battery packs that are in good condition. Do not use with damaged, swollen, or over-discharged batteries. Always double-check battery polarity before connecting to prevent module damage and fire.

CRITICAL: Toggle switch must match the battery configuration.

The module must be configured via the toggle switch to match your battery pack's cell count (2S-5S) and chemistry (Li-ion / LiFePO4). Incorrect settings will overcharge or undercharge the battery, causing permanent damage or fire.

CAUTION: Use 20V input to achieve full 30W output.

To achieve the maximum 30W charging power, you must use a 20V PD-compliant power supply. Lower input voltages will result in reduced charging power.

Electrical Safety:

  • Input voltage: 5-20V (PD/QC or direct DC).
  • Maximum output: 30W (requires 20V input).
  • Battery compatibility: Li-ion: 4.2V-12.6V (2S-5S) / LiFePO4: 3.6V-18V (2S-5S).
  • Power modes: 20W / 30W (default 30W).
  • Observe correct battery polarity (+/-) - reverse connection will damage the module.
  • Use thick output cables (e.g., 18AWG) to avoid power loss.
  • Do not short-circuit the battery output terminals.
  • Keep the module away from water, moisture, and conductive debris.
  • Ensure adequate ventilation - the module may generate heat during charging.

Handling Precautions:

  • This module contains ESD-sensitive components. Use proper ESD precautions during handling.
  • Handle the PCB by the edges to avoid damaging components.
  • Do not bend or flex the PCB - it may crack solder joints.
  • Do not operate the module in explosive or flammable atmospheres.

3. Technical Specifications

Parameter Specification
Product Type Auto Buck-Boost PD Fast Charger Module
Controller IC IP2363
Input Voltage 5-20V (PD/QC or direct DC)
Max Output Power 30W (requires 20V input)
Power Modes 20W / 30W (default: 30W)
Battery Support 2S-5S Li-ion (4.2V-12.6V) / LiFePO4 (3.6V-18V)
Configuration Toggle switch (cell count + chemistry)
Protection Features Overvoltage protection, timeout protection, reverse polarity protection
LED Indicators Flashing = Charging / Solid = Full / Rapid Blink = Fault
Recommended Cable Gauge ≥ 18AWG (for output to minimize power loss)
Dimensions 4.6 x 3.8 cm
Operating Temperature -20°C to +70°C
Certifications CE, RoHS, WEEE Compliant

4. Setup & Configuration

Connection Setup:

  1. Configure the Module: Before connecting the battery, set the toggle switch to match your battery pack:

    • Select the correct cell count (2S, 3S, 4S, or 5S).
    • Select the correct chemistry (Li-ion or LiFePO4).

    Note: Incorrect configuration will overcharge or undercharge the battery - verify carefully!

    Side view of the IP2363 module showing the DIP switch

    Figure 2: Side view of the IP2363 module, clearly showing the red DIP switch for configuration.

    For LiFePO4 batteries, you may need to replace a resistor yourself. Refer to the PSET section on the PCB bottom for resistor values:

    • Ternary Li-ion (4.2V) default: 9.1K=4S (13K=30W default), 6.2K=3S (6.2K=20W)
    • Lithium Iron Phosphate (3.65V) (LiFePO4): 9.1K=30W, 3.6K=20W
    Bottom view of the IP2363 module showing PSET resistor options

    Figure 3: Bottom view of the IP2363 module, displaying the PSET resistor configuration options for different battery types and power modes.

  2. Connect Battery: Connect your battery pack to the B+ and B- terminals, observing correct polarity. Double-check polarity - reverse connection will damage the module.

  3. Connect Power: Connect a PD/QC power supply or direct DC source (5-20V) to the input terminals (USB-C or +IN/-IN). For maximum 30W output, use a 20V PD-compliant power supply.

    Angled view of the IP2363 module showing USB-C input and output terminals

    Figure 4: Angled view of the IP2363 module, showing the USB-C input and the blue output terminal block.

5. Operation

Charging Process:

  1. Ensure the module is correctly configured and connected as per the Setup section.
  2. Connect the power source. The module will begin charging the battery.
  3. Monitor LEDs: Observe the LED status indicators to confirm charging progress.
  4. Disconnect: Once the LED is solid on, the battery is fully charged. Disconnect the battery promptly.

LED Status Indicators:

  • Flashing: Charging in progress.
  • Solid On: Fully charged.
  • Rapid Blinking: Input overvoltage or charging timeout fault.

Power Mode Selection:

The module supports two power modes: 20W and 30W.

  • Default setting is 30W (requires 20V input).
  • To switch to 20W mode, refer to the configuration instructions on the PCB (PSET resistor values).

For Optimal Performance:

  • Use a 20V PD-compliant power supply to achieve the full 30W charging power.
  • Ensure output cables are thick enough (e.g., 18AWG) to minimize power loss.
  • Use high-quality PD/QC chargers for reliable performance.
  • Charging power will taper near the full charge state - this is normal behavior.

Video 1: Demonstration of the IP2363 module charging a battery pack via USB-C, showing the LED indicator.

6. Maintenance & Storage

Cleaning:

  • Disconnect all power before cleaning.
  • Use a soft, dry brush or compressed air to remove dust.
  • Do not use water, solvents, or wet cleaning methods.

Storage:

  • Store in a dry, dust-free environment at room temperature (15°C - 35°C).
  • Avoid direct sunlight, high humidity, and corrosive atmospheres.
  • If not used for an extended period, store in an anti-static bag.
  • Before re-use, inspect the terminals for corrosion or damage.

Handling:

  • Avoid dropping or mechanical stressing the module.
  • Protect the input and output terminals from damage.

7. Troubleshooting

  • Module not charging / Insufficient power output:
    • Verify input power meets PD/QC standards and is within the 5-20V range. For 30W output, a 20V PD-compliant supply is required.
    • Check output wire gauge; ensure cables are thick enough (e.g., 18AWG) to handle current and minimize power loss.
    • Ensure the battery pack is in good condition (not damaged, swollen, or over-discharged).
  • Rapid Blinking LED: This indicates an input overvoltage or charging timeout fault. Check your input power supply and battery connections.
  • Module damage after connection: Always double-check battery polarity (+/-) before connecting. Reverse connection will damage the module.
  • Battery not fully charging or overcharging: Ensure the toggle switch configuration for cell count and chemistry (Li-ion/LiFePO4) precisely matches your battery pack. Incorrect settings can lead to improper charging.

8. User Tips

  • Always use high-quality PD/QC chargers for reliable performance and optimal charging speeds.
  • Consider using a USB-C power meter to monitor input voltage and current, especially when troubleshooting power output issues.
  • When working with LiFePO4 batteries, remember that resistor modification is required for proper voltage settings. Double-check the PSET values on the PCB.
  • For DIY projects, ensure all connections are secure and insulated to prevent accidental short circuits.

9. Compliance Information

This product complies with the essential requirements of applicable European Directives, including but not limited to:

  • CE Marking: The product bears the CE mark in accordance with applicable EU harmonization legislation.
  • RoHS Directive (2011/65/EU): This product is compliant with the Restriction of Hazardous Substances Directive.
  • WEEE Directive (2012/19/EU): This product must be disposed of separately from household waste. This symbol indicates that this product should not be treated as household waste. For proper disposal, take the product to a designated collection facility for electrical and electronic equipment and follow local regulations.
  • EMC Directive (2014/30/EU): This product meets electromagnetic compatibility requirements when installed properly.

CE

CE Mark (Must be printed here with a height of not less than 5mm)

WEEE symbol (crossed-out wheeled bin)

WEEE (Crossed-out wheeled bin symbol must be printed here)

10. Manufacturer & Support Information

Manufacturer:

Shenzhen yakaiyao Trading Co., Ltd.
Address: 202, building s, No.1, 1st Road, Xiawei Industrial Zone Zhangkengjing community Guanhu Street Longhua District, Shenzhen
Email/Tel: 1241273859@qq.com

EU Authorized Representative:

MJCM SARL
Address: 78 avenue des Champs Elysees Bureau 326 France
Email: mjcm190928@gmail.com

For further assistance, please refer to the official user manual PDF: View User Manual (PDF)

© 2026 Product Manual — All rights reserved. Version: 1.0

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.