ETENWOLF VORTEX S6

Contents

ETENWOLF VORTEX S6 Portable Air Compressor

User Manual

Introduction

Thank you for choosing the ETENWOLF S6 Air Compressor. Built for inflating the most various types of tires and inflatables, this compact power station-like pump helps to broaden usability during travel. This manual provides detailed instructions for setup, operation, maintenance, and troubleshooting to ensure safe and efficient use of your device.

For a comprehensive guide, you may also refer to the official user manual PDF: ETENWOLF Vortex S6 User Manual (PDF)

Package Content

The ETENWOLF VORTEX S6 comes with the following items:

  • S6 Air Compressor x 1
  • Air Chuck x 1
  • High-pressure hose x 1
  • High-volume hose x 1
  • 45W PD charger x 1
  • USB C to C cable x 1
  • User manual x 1
Diagram of package contents including the S6 Air Compressor, hoses, charger, and accessories.
Diagram of the ETENWOLF S6 package contents.
Photo of all items included in the ETENWOLF S6 package, neatly arranged.
Photo of the ETENWOLF S6 Air Compressor and its accessories.

Product Overview

Familiarize yourself with the components of your ETENWOLF S6 Air Compressor:

Diagram showing the various parts of the ETENWOLF S6 Air Compressor, including buttons, display, ports, and hoses.
Detailed diagram of the ETENWOLF S6 Air Compressor components.
No.ComponentNo.Component
01Start/pause power button17Type-C port (input/output)
02Pressure adjustment knob18USB-A port (input)
03Center display19Safety alert symbol
04Mode button20Manual mode
05Light button21Car mode
06Unit button22Pickup truck mode
07LED Worklight23Recreational vehicle mode
08Inlet/Deflation port24Ball mode
09High-pressure hose25High flow inflation/deflation mode
10Outlet/Inflation port26Bicycle mode
11Inlet/Outlet Nubs27Pressure unit
12High-volume hose28Target input value
13High-volume tapered nozzle29Actual pressure value
14High-pressure tapered nozzle30Temperature protection indicator
15Inflation needle31Battery level indicator
16Presta valve adapter

Quick Start Guide

To Inflate Using High Volume

  1. Remove the high-volume hose (12) from its storage channel. Line up the notches of the hose with the nubs (11) of the high-volume pump outlet/inflation port (10). Then, slide the hose on and twist counter-clockwise to secure.
  2. Choose the right tapered nozzle (13) and insert it into the object to be pumped.
  3. Press the START/PAUSE power button (01) to activate the machine.
  4. Press MODE button (04) to switch to High flow inflation/deflation mode (25).
  5. Then press the START/PAUSE power button (01) to turn the pump on.
  6. Press the power button (01) again to turn off.
Diagram showing steps for high volume inflation with the ETENWOLF S6.
Steps for high volume inflation.

NOTE: Users need to pause the inflation manually. Leaving it on for too long will lead to an inflated item explosion.

To Deflate Using High Volume

Attach the high-volume hose (12) to the Inlet/deflation port (08). Follow steps 2 through 6 in the above section about inflation.

To Inflate Using High-Pressure

  1. Remove the high-pressure hose (09) from its storage channel.
  2. Insert the nozzle clockwise into the object being inflated.
  3. Press the START/PAUSE power button (01) to activate the machine.
  4. Press MODE button (04) to switch among six different modes: Manual mode (20), Car mode (21), Pickup truck mode (22), Recreational vehicle mode (23), Ball mode (24), Bicycle mode (26).
  5. Select the pressure unit between PSI, kPa, and Bar by pressing the UNIT button (06).
  6. Rotate the pressure adjustment knob (02) to set the desired pressure.
  7. Press START/PAUSE power button (01) again to start inflation.
  8. When the inflated item reaches the preset value, the unit will turn off automatically.
Diagram showing steps for high pressure inflation with the ETENWOLF S6.
Steps for high pressure inflation.

NOTE:

  • To stop inflation at any time, press the START/PAUSE power button.
  • ETENWOLF system will automatically remember the previous pressure settings when the unit is used again.
  • Double check the target input value. Setting a wrong value might lead to an inflated item explosion.
  • After the tire is inflated, the temperature inside the tire will decrease to the ambient temperature, causing the tire pressure to decrease by 0.5 to 1.5 psi.
  • When finishing pumping a bike tire, don't forget to quickly remove the hose. Otherwise, the losing air may lessen the tire pressure.

Button Operation Guide

START/PAUSE Power Button

  • ON: Long-press START/PAUSE power button (01) for one second to turn on.
  • OFF: When the inflator is turned on, long-press START/PAUSE power button (01) for two seconds to turn off.
  • Pause: When the inflator is inflating/deflating, press the button to pause the machine at any time.

The inflator will automatically turn off in the cases below:

  1. 5 minutes of inactivity.
  2. When the charging cable is accidentally disconnected during charging.
  3. 5 minutes of inactivity after being fully charged.
  4. 5 minutes inactivity after being used as a power bank.
  5. When inflating over 5 minutes, but the actual pressure is still below 5 psi.
  6. When inflating over 5 minutes, but the actual pressure is above 160 psi.

MODE Button

Press MODE button (04) to switch between six inflation modes and one deflation mode.

UNIT Button

Press UNIT button (06) to switch between the three pressure units BAR/PSI/KPA.

Pressure Adjustment Knob

Rotate the Pressure adjustment knob (02) clockwise to increment pressure value and rotate the knob counter-clockwise to decrement pressure value.

Preset Pressure Value

The number with the smaller size on the top of the display indicates the target input (28), and the number with the bigger size on the bottom of the display indicates the actual value (29) of the inflated devices.

ModeAdjustable Pressure RangeDefault Pressure
Car Mode8-50 psi35 psi
Pickup truck Mode10-85 psi35 psi
Recreational vehicle Mode20-130 psi60 psi
Bicycle Mode10-145 psi22 psi
Ball Mode3-16 psi8.5 psi
Manual Mode0-160 psi30 psi
Deflation Mode

Memory the pressure setting:

Each time you adjust the pressure setting, the ETENWOLF inflator will remember your new target pressure value and unit option, which means you can change the default pressure at any time.

LED Work Light

An LED work light (07) is located on the side of the handle. To turn the light on, first power on the machine by pressing the START/PAUSE button (01) and then press LIGHT button (05).

Switch between four different light modes:

  • Bright flashlight: 300 Lumen light
  • Ultra-bright flashlight: 1000 Lumen light
  • Slow strobe light: light turns on and off.
  • SOS signal: 3 short strobe signals, followed by 3 long strobe signals, and then 3 more short strobe signals, repeated in a loop.

Note:

The light will automatically turn off after 1 hour. Once the hour has elapsed and the light is turned off, if you turn it on again, it will not turn off until the battery is exhausted.

Diagram showing the three emergency lighting modes: Emergency lighting mode (Light stays on), Alarming SOS mode (Light flashes alternately), and Strobing mode (Light strobes for warning).
Emergency Lighting Modes.

Power Bank Functionality

The power bank is ready to charge all your electronic devices such as phone, tablet, laptop, drone and camera. It has USB-A Output 5V 2A, and USB-C Output 45W Max, 5/9/12/15V 3A, 20V/2.25A.

Note:

  1. To work as a power bank, the inflator needs to power on.
  2. After 3 minutes of charging, the display panel will only indicate the battery level to save battery.
  3. After 2 minutes of fully charging the devices, the inflator will automatically turn off.
Diagram showing the ETENWOLF S6 being charged via USB-C and also charging a tablet via USB-C, illustrating its two-way fast charging capability.
Two-way Fast Charging.

Battery Charging & Indicator

Battery Indicator

The battery level indicator (31) is shown by four bars, with each bar representing 25% of capacity.

Diagram showing battery level indicators from 0% to 100% charged.
Battery level indicators.

Note:

Battery indicator will flash when the battery level drops to below 10%.

Charging with the AC power supply

For the best charging performance and stability, use a 45W PD charger to fuel your built-in battery. Battery charging takes approximately 2 hours from 0% to 100% fully charged.

Note:

  • After 2 minutes of inactivity after being fully charged, the inflator will automatically shut off.
  • The inflator cannot be used while it is charging.

Pressure Recalibration

Different altitudes can cause variant in the pressure by 1-3 PSI. When in high altitude areas (especially over 5000 ft/1524 meters), users are able to recalibrate the pump's pressure sensor.

Recalibration steps:

  1. Turn on the pump, and simultaneously hold down the Light button (05) and Mode button (04) for 10 seconds.
  2. Once the display is flashing, the pump is recalibrated successfully.

Note:

  • Power on the pump before starting calibration.
  • The high-pressure hose (09) should not be connected to any item. Any item which gives pressure to the hose will disable the process of recalibration.
  • A charged battery or other power source is required to process recalibration.
  • There is no memory for the new recalibration settings. Once the power is turned off, it will be reset to sea level calibration (altitude 0 ft/meters).
  • At high altitudes above 5000 ft/1524 meters, manual calibration of the air pump is required each time you turn it on.

Troubleshooting

If you encounter any issues with your ETENWOLF S6, refer to the table below for solutions:

ProblemSolution
Slow inflation speed
  • Check whether the battery is sufficient.
  • Check whether the item inflated is leaking.
  • Check whether the Inlet/Outlet ports are leaking.
  • Check whether the inflation hoses are broken.
  • Check whether the ventilation slots are blocked.
Air compressor turns on, but does not inflate
  • Check whether the battery is sufficient.
  • Check whether the pressure of the item being inflated exceeds the preset pressure.
The inflator inflates but the pressure shown on the display is zero.If the air pressure is under 3PSI, the pressure displayed will show zero due to the pump's minimum pressure range.
Unable to increase or decrease the preset pressureMake sure the correct mode is chosen, and the preset value does not exceed the range.
The battery level indicator is different when inflating compared to the standby state.The lithium battery's voltage level significantly drops when discharging power, causing the battery level indicator to have a different display when inflating compared to a standby state. It is a normal situation.
The battery level indicator does not show on the screen after charging.Use a certified ETENWOLF charger or PD charger and the included charging cable, and try to charge it again.
The inflator stops working because of extreme temperature conditions.When inflating, deflating, and discharging the pump, ensure that the working temperature is between -20°C/-4°F and 70°C/158°F. When charging the pump, ensure that the working temperature is between 0°C/32°F and 45°C/113°F.
Safety alert symbol light on when abnormal pressure is detected or the inflation motor reacts abnormally.Power off the machine, wait for 10 minutes and restart it. If the issue persists, send the device for factory repair.
Display shows the E08 error code.This indicates a motor malfunction. If the issue persists after restarting, send the device for factory repair.
Display shows the E13 error code.Low-temperature discharge protection. Restore temperature above -20°C before continuing.
Display shows the E14 error code.High-temperature discharge protection. Restore temperature below 58°C before continuing.
Display shows the E15 error code.Air pump exceeded working time. Check for leaks.
Display shows the E16 error code.Overpressure protection. Returns to normal after pressure release.
Display shows the E17 error code.High-pressure operation exceeded working time. Check if the inflated item is functioning abnormally.
Display shows the E18 error code.Battery damage warning. Device will shut down after 30 seconds. Send for factory repair.

Specifications

FeatureSpecification
NameAir Compressor
ModelVortex S6
Dimensions309×237×142mm (Excluding air tube)
Inflation Pressure Range3-160PSI / 0.2-11.0bar
Operating Temperature (Charging)32°F~113°F / 0°C~45°C
Operating Temperature (Discharging)-4°F~165°F / -20°C~74°C
Storage Temperature-4°F~140°F / -20°C ~ 60°C
High Volume Air Tube Length800mm
Battery CapacityS6 19,200mAh (71Wh), S6 Plus 26,400mAh (97Wh)
Working NoiseLower than 85dB within 1 meter
InputType-C PD3.0 PD45W: 5V 3A, 9V 3A, 12V 3A, 15V 3A, 20V 2.25A
OutputType-C PD3.0 PD45W: 5V 3A, 9V 3A, 12V 3A, 15V 3A, 20V 2.25A; USB-A 5V/2.4A
Input PortType-C
Output PortType-C/USB-A
Charging time45W S6: 2 Hours / S6 Plus: 2.5 Hours
Sensor accuracy±1 psi

Safety Instructions

Warning! Please read all safety warnings and all instructions to reduce the risk of electric shock, fire and/or serious injury.

  1. This product is not a toy and should not be used by children. Users should be above 16 years old. Keep a safe distance between children and the inflator while inflating. There is a built-in lithium battery inside the product. Don't place the product into fire or dump the battery.
  2. Overheating damage or water ingress may increase the risk of fire or explosion. It's best to keep the product away from heat sources, and not leave it for prolonged periods in a hot car. If the inflator becomes very hot, there is a chance it could explode.
  3. Please store the product within temperatures ranging from -4°F~140°F/-20°C~60°C. Extremely hot or cold environments may damage the battery and shorten the lifetime of the inflator. Long-time storage of the product may decrease the effectiveness of the battery. Charge the inflator at least once every three months to maintain its performance.
  4. The product has a built-in DC motor which may generate sparks during operation. Do not use it in an environment with dust or gas that is liable to explode.
  5. If there is an unusual noise or the temperature becomes very high during inflating, please turn off the inflator immediately.
  6. Before setting the inflation pressure value, make sure the pressure unit is correctly selected. Mixing up psi and bar could lead to dangerous overinflation.
  7. Unit conversion: 1bar = 14.5psi. 1bar = 100kPa.
  8. Do not leave the pump unattended while it is in operation.
  9. Please use the product in a dry and clean environment. The intrusion of sand and dust may cause damage to the product. Don't wash the product with water.
  10. Make sure to use ETENWOLF's charger or other certified PD chargers, and the included charging cable to charge this product. Malfunction caused by actions not in accordance with the above requirements is not covered by the warranty.
  11. To reduce the risk of electric shock, do not expose to rain. Store indoors.

Warranty & Support

2-Years Coverage

Within two years of purchase, we will provide timely and effective online after-sale service. We will repair or replace any defective product (due to manufacturing fault) within this warranty period.

Contact Information

Manufacturer: Mozhen Technology (Shenzhen) Co., Ltd

Address: CN-503, Floor 5, Building 4, Tianan Yungu Industrial Park Phase II, Gangtou Community, Bantian Street, Longgang District, Shenzhen

Phone: (1)877-838-0209 Mon-Fri 8AM-5PM(PST)

Email: support@etenwolf.com

Website: www.etenwolf.com

Facebook: www.facebook.com/etenwolftools

Made in P.R.C

Register at www.etenwolf.com to receive a 1-year extended warranty.

Product Demonstration Video

Video demonstrating the ETENWOLF S6 Portable Air Compressor in use, showing its features and ease of operation for various vehicles.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.