Makerbase MKS SERVO28D/35D

Contents

Makerbase MKS SERVO28D/35D Closed-Loop Stepper Motor Driver User Manual

For NEMA11/NEMA14 Stepper Motors

1. Introduction

The Makerbase MKS SERVO28D and SERVO35D are advanced closed-loop stepper motor drivers designed for precise control of NEMA11 and NEMA14 stepper motors. These drivers support multiple control interfaces including Pulse signal, RS485, and CAN, enabling accurate position, speed, and torque control. They are ideal for CNC machines, 3D printers, and other applications requiring high precision and efficiency.

Makerbase MKS SERVO driver mounted on a stepper motor with OLED display showing status.
Figure 1: MKS SERVO driver mounted on a stepper motor, displaying operational status on the OLED screen.

2. Package Contents

Depending on the specific model purchased, your package may include:

  • MKS SERVO28D or MKS SERVO35D Driver Board
  • OLED Display Module
  • Adapter Board (if applicable)
  • Wiring Harness
Components of the MKS SERVO35D RS485 driver kit.
Figure 2: Typical components included with the MKS SERVO35D RS485 driver: driver board, OLED module, adapter, and wiring.

3. Setup and Wiring

Proper wiring is crucial for the correct operation of the MKS SERVO driver. Refer to the diagrams below for connection details.

3.1. Motor Connections

Connect the stepper motor phases to the A+, A-, B+, B- terminals on the driver board. Ensure correct polarity.

  • A+: Motor Phase A Positive
  • A-: Motor Phase A Negative
  • B+: Motor Phase B Positive
  • B-: Motor Phase B Negative

3.2. Control Signal Connections (Pulse Mode)

For pulse control, connect your controller's signals to the corresponding pins on the driver.

  • V+: Power Supply Positive Input
  • Gnd: Power Supply Ground
  • En: Enable Signal (typically active low)
  • Stp: Step Pulse Input
  • Dir: Direction Input
  • Com: Common Ground for Control Signals
  • SV: (Specific to some models, refer to detailed pinout)
  • IN: (Specific to some models, refer to detailed pinout)

3.3. Communication Connections (RS485/CAN)

For RS485 or CAN communication, connect the respective data lines.

  • RS485:
    • +R: RS485 Data Positive
    • -R: RS485 Data Negative
  • CAN:
    • CAN_H: CAN High
    • CAN_L: CAN Low
Top and bottom view of MKS SERVO28D RS485 driver board with pin labels.
Figure 3: MKS SERVO28D RS485 driver board showing pin assignments for motor, control, and communication.
Close-up of MKS SERVO28D CAN driver board showing motor and communication terminals.
Figure 4: Close-up of MKS SERVO28D CAN driver board terminals, highlighting motor (A+, A-, B+, B-) and CAN connections.

3.4. Power Supply

Connect a suitable DC power supply to the V+ and Gnd terminals. Ensure the voltage and current capacity meet the requirements of your motor and application.

3.5. OLED Display Connection

Connect the OLED display module to the dedicated header on the driver board. This display provides real-time status, error messages, and allows for parameter configuration.

4. Operating Instructions

The MKS SERVO drivers operate in a closed-loop manner, constantly monitoring the motor's position to ensure accuracy. The OLED display and onboard buttons (Next, Enter, Menu) allow for configuration and monitoring.

4.1. Power On

After all connections are secure, apply power to the driver. The OLED display should light up, showing initial status or a welcome screen.

4.2. Display Navigation

  • Next: Navigate through menu options or display screens.
  • Enter: Select an option or confirm a setting.
  • Menu: Access the main menu or go back to the previous screen.

4.3. Control Modes

The driver supports different control modes:

  • Pulse Control: Standard step/direction interface for position control.
  • RS485 Control: Allows for communication and control via Modbus or a custom protocol over RS485.
  • CAN Control: Enables communication and control via CAN bus, often used in industrial automation.

Refer to the specific firmware documentation or the manufacturer's website for detailed commands and protocols for RS485 and CAN control.

4.4. Parameter Configuration

Through the OLED menu, you can configure various parameters such as:

  • Motor parameters (steps per revolution, current limits)
  • Control loop gains (PID settings for position, speed, torque)
  • Communication settings (Baud rate, device ID)
  • Error thresholds and responses

5. Maintenance

The MKS SERVO drivers are designed for reliability with minimal maintenance. Follow these guidelines to ensure longevity:

  • Keep Clean: Ensure the driver board is free from dust, debris, and moisture. Use compressed air to clean if necessary.
  • Check Connections: Periodically inspect all wiring connections for looseness or corrosion.
  • Environmental Conditions: Operate the driver within its specified temperature and humidity ranges. Avoid extreme conditions.
  • Firmware Updates: Check the Makerbase official website for any available firmware updates that may improve performance or add features.

6. Troubleshooting

If you encounter issues with your MKS SERVO driver, refer to the following common problems and solutions:

6.1. Driver Not Powering On / OLED Blank

  • Check Power Supply: Verify that the power supply is connected correctly and providing the correct voltage.
  • Check Wiring: Ensure V+ and Gnd connections are secure and not reversed.
  • OLED Connection: Confirm the OLED display module is properly seated.

6.2. Motor Not Moving or Moving Erratically

  • Motor Wiring: Double-check the A+, A-, B+, B- connections to the motor for correct polarity and secure contact.
  • Control Signals: In pulse mode, verify that the Step, Direction, and Enable signals are correctly wired and being sent by your controller. Ensure the Enable signal is active (usually low).
  • Power Supply: Ensure the power supply has sufficient current capacity for the motor.
  • Motor Parameters: Check motor configuration settings (e.g., steps per revolution) in the driver's menu.
  • Error Display: Check the OLED display for any error codes (e.g.,
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.