BENINCA TO GO 2A

Contents

BENINCA TO GO 2A Garage Door Remote Control User Manual

Model: TO GO 2A

1. Introduction

This manual provides detailed instructions for the setup, operation, and maintenance of your BENINCA TO GO 2A garage door remote control. This remote utilizes Advanced Rolling Code (ARC) technology for enhanced security and reliable performance. Please read this manual thoroughly before attempting to program or operate the device.

2. Safety Information

  • Keep the remote control out of reach of children to prevent accidental operation of the garage door.
  • Do not expose the remote control to water or extreme temperatures.
  • Dispose of used batteries responsibly according to local regulations.
  • Ensure the garage door path is clear before operating the remote control.

3. Product Overview

The BENINCA TO GO 2A is a compact and durable remote control designed for garage door and gate openers. It features two buttons for controlling different functions or multiple doors.

Front view of the BENINCA TO GO 2A remote control

Figure 3.1: Front view of the BENINCA TO GO 2A remote control.

Multiple views of the BENINCA TO GO 2A remote control, including side and back

Figure 3.2: Various angles of the TO GO 2A remote control, showing its design and compact size.

4. Specifications

FeatureDescription
Model NumberBENINCA TO GO 2A
Number of Channels2
Frequency433.92MHz
Encoding MethodRolling Code (Advanced Rolling Code - ARC 128 Bit)
Battery12V 23A
Operating Temperature-20°C to +50°C
Dimensions65x40x14 mm
CertificationCE

What is ARC?

The Advanced Rolling Code (ARC) technology, with its 128-bit transmitted code (compared to the previous 64-bit version), ensures maximum security against unauthorized access by constantly changing the transmission code.

5. Setup and Programming

The BENINCA TO GO 2A remote control is programmed directly with your receiver unit. Important: You must have physical access to your garage door or gate opener's receiver unit to perform the programming steps.

  1. Locate the Receiver: Open the casing of your receiver unit. It is typically located next to your garage door or gate motor.
  2. Activate Programming Mode: On the receiver's circuit board, press the programming button, usually labeled 'PGM'. The LED light on the receiver will illuminate. Release the 'PGM' button.
  3. Pair the Remote: Within the next 10 seconds, press a button on your new BENINCA TO GO 2A remote control. Release the button.
  4. Confirm Programming: Wait for approximately 10 seconds. Your new remote control should now be programmed and ready for use.
Diagram of a receiver circuit board with a PGM (programming) button and LED, illustrating the programming process

Figure 5.1: Example of a receiver circuit board showing the 'PGM' button and LED indicator for programming.

6. Operating Instructions

Once programmed, operating your BENINCA TO GO 2A remote control is straightforward:

  • Press the programmed button on your remote control to open or close your garage door or gate.
  • If you have programmed multiple functions or doors, use the corresponding button for each action.
Hand holding the BENINCA TO GO 2A remote control with a garage door in the background, indicating its function

Figure 6.1: Demonstrating the use of the remote control to operate a garage door.

7. Maintenance

Battery Replacement

The BENINCA TO GO 2A remote control uses a 12V 23A battery. If the remote's range decreases or it stops responding, it's likely time to replace the battery.

  1. Carefully open the remote control casing.
  2. Remove the old 12V 23A battery.
  3. Insert a new 12V 23A battery, ensuring correct polarity.
  4. Close the remote control casing securely.

8. Troubleshooting

Compatibility Warning

The BENINCA TO.GO2A remote control is not compatible with the similar-looking BENINCA TO.GO2WV remote control. Please ensure you have the correct model for your receiver.

Comparison image showing BENINCA TO.GO2A (ARC) and BENINCA TO.GO2WV (Rolling Code) remotes, highlighting incompatibility

Figure 8.1: Visual guide to distinguish between TO.GO2A (ARC) and TO.GO2WV (Rolling Code) models.

Common Issues and Solutions

  • Remote not responding: Check the battery. If the battery is new, try re-programming the remote control with the receiver.
  • Reduced range: Replace the battery. Ensure there are no obstructions between the remote and the receiver.
  • Lost remote control: If your remote control is lost, you can purchase a new BENINCA TO GO 2A remote and program it to your existing receiver following the steps in Section 5. This will effectively replace the lost remote.

9. User Tips

  • Programming with Electric Gates: The programming method for electric gates is generally the same as for garage doors. Always ensure you have access to the gate's receiver unit and follow the steps outlined in Section 5.
  • Verify Model: Before purchasing a replacement or additional remote, double-check that your existing remote and receiver are compatible with the BENINCA TO GO 2A (ARC) model, especially noting the visual differences from the TO.GO2WV model.

10. Package Contents

Your BENINCA TO GO 2A remote control package includes:

  • BENINCA TO GO 2A Remote Control
  • 12V 23A Battery
  • Keychain
  • English User Manual (printed)
  • White Box Packaging
Contents of the product package: remote control, battery, keychain, and manual

Figure 10.1: All items included in the BENINCA TO GO 2A remote control package.

11. Additional Resources

For further details or if you require a digital copy of the manual, you may refer to the official PDF document: User Manual (PDF)

12. Warranty and Support

For warranty information and technical support, please refer to the documentation provided with your purchase or contact the seller directly. Keep your proof of purchase for any warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.