Sunster 5KW Liquid Heater

Contents

Sunster 12V 5KW Liquid Heater Instruction Manual

Model: 5KW Liquid Heater

1. Introduction

This manual provides detailed instructions for the safe and efficient operation, installation, and maintenance of your Sunster 12V 5KW Liquid Heater. Designed to pre-heat your vehicle's engine and interior, this device ensures comfortable conditions and reduces engine wear in cold weather. Please read this manual thoroughly before installation and use.

2. Safety Information

  • Fuel Compatibility: Diesel and gasoline fuels cannot be mixed simultaneously. If you need to change the fuel type, ensure the original fuel is completely used up before introducing a different type.
  • Installation Position: The water pump and main heater unit should be installed lower than the vehicle's original water kettle, PTC, and warm air tank.
  • Oil Pump Outlet: Install the oil pump outlet at a 45° angle upwards, preferably close to the main engine.
  • Exhaust Pipe: The exhaust pipe must face towards the rear of the vehicle and should not face the direction of vehicle travel or the ground. It is strictly prohibited for the exhaust pipe to come into contact with flammable materials.
  • Intake Pipe: The intake pipe can only be connected to the original air filter. Do not use obstructions to cover it. It must not be in the same direction as the exhaust pipe.
  • Fuel Type Selection: To ensure normal heating in cold winter, do not use inferior diesel. Choose the corresponding diesel model according to the local temperature.
  • Post-Installation Check: After installation, thoroughly check all connecting parts to ensure the circuit is well connected and there is no oil leakage or blockage in the oil circuit.
  • Overheating Protection: The unit is equipped with overheating protection.
  • Low Voltage Protection: The unit features low voltage protection to prevent damage to the vehicle's battery.
Warning about mixing diesel and gasoline fuels
Important warning regarding fuel compatibility.
Diagram showing overheating and low voltage protection features
The heater includes overheating and low voltage protection for safe operation.

3. Product Overview and Components

The Sunster 12V 5KW Liquid Heater is a compact and efficient heating solution for various vehicles. It features a robust design with a brushed motor and brushless water pump for silent and low-noise operation.

Sunster 12V 5KW Liquid Heater and included components
Main unit and complete kit contents.

3.1 Main Components

Diagram of all included components for the liquid heater kit
Detailed view of the heater kit components.
  • Host: The main heating unit.
  • Controller: LCD display unit for settings and monitoring.
  • Remote Control: Wireless remote for convenient operation.
  • Oil Pump Clamp: Secures the oil pump.
  • Hose: Various hoses for fuel and coolant lines.
  • Air Filter: Filters air intake for combustion.
  • Silencer: Reduces exhaust noise.
  • Heater Relay: Electrical component for heater control.
  • Oil Pump: Delivers fuel to the heater.
  • Oil Filter: Filters fuel before it reaches the pump.
  • Water Pump: Circulates coolant through the heater.
  • Fixed Plate: Mounting bracket for the heater.
  • Tubing: Additional tubing for connections.
  • Manual: User instruction manual.
  • Exhaust Pipe: Directs exhaust gases away from the vehicle.
  • Harness: Wiring harness for electrical connections.
  • Screw Accessory Kit: Various screws and fasteners for installation.

3.2 Internal Structure

Exploded view diagram of the liquid heater's internal components
Internal components: 1. Aluminum body, 2. Combustion chamber, 3. Motherboard, 4. Aluminum lower cover, 5. Internal motor assembly, 6. Inner wind wheel, 7. Aluminum cover.

4. Specifications

Product dimensions and detailed specifications table
Dimensions and key performance specifications.
AttributeValue
Brand NameSunster
Item TypeHeating & Fans
Switch TypeLCD Switch
Voltage12V
Power (W)5000W (5KW)
Rated Heat Flow Rate5W
FuelGasoline / Diesel
Work Voltage9V~16V
Power Consumption≤ 39W
Fuel Consumption0.1~0.24L/H (Image also indicates 0.55L/H)
Item Weight5kg (Package weight: 6.0kg)
Item Length24cm (Overall Dimensions: 230mm)
Item Width9.5cm (Overall Dimensions: 90mm)
Item Height18cm (Overall Dimensions: 165mm)
Working Temperature-40°C~80°C
Remote Control Distance80 Meters (Image also indicates 150 Meters)
External Testing CertificationCE
OriginMainland China

*Note: Some specifications may vary slightly between different data sources. Refer to the product packaging for the most accurate information.

5. Installation Guide

The compact design of this heater allows for installation in various narrow spaces. Follow these guidelines for proper and safe installation.

Liquid heater installed in a vehicle engine bay
Example installation of the liquid heater in a vehicle.

5.1 Installation Precautions

  1. The installation position of the water pump and host should be lower than the original water kettle, PTC, and warm air tank of the vehicle.
  2. The oil pump outlet should be installed at a 45° angle upwards, preferably close to the main engine.
  3. The exhaust pipe should face towards the rear of the vehicle, and should not face the direction of vehicle travel or the ground. It is also prohibited to come into contact with flammable materials.
  4. The intake pipe can only be connected to the original air filter, and it is forbidden to use obstructions to cover it. It must not be in the same direction as the exhaust pipe.
  5. To ensure that the heater can provide normal heating in the cold winter, please do not use inferior diesel and choose the corresponding diesel model according to the local temperature.
  6. After the installation of the equipment is completed, the connecting parts of each part should be checked to see if the circuit is well connected and if there is any oil leakage or blockage in the oil circuit.
Diagram illustrating installation precautions for the liquid heater
Visual guide for installation precautions, including pump and exhaust orientation.

5.2 Port Identification

Diagram showing the water inlet, water outlet, exhaust port, air inlet, and oil drain on the heater
Key connection points on the heater unit: Water Outlet, Water Inlet, Exhaust Port, Air Inlet, Oil Drain.
  • Water Outlet: Connects to the vehicle's coolant system for heated coolant return.
  • Water Inlet: Connects to the vehicle's coolant system for cold coolant intake.
  • Exhaust Port: For expelling combustion gases.
  • Air Inlet: For drawing in air for combustion.
  • Oil Drain: For draining fuel from the unit.

6. Operating Instructions

The Sunster Liquid Heater offers convenient operation via an LCD switch and a wireless remote control.

LCD switch and wireless remote control with button functions
LCD Switch and Remote Control interface details.

6.1 LCD Switch Operation

  • ON/OFF Button: Powers the unit on or off.
  • UP/DOWN Buttons: Adjust settings such as temperature or timer.
  • SET Button: Confirms selections or enters settings menus.
  • The LCD displays current water temperature, operating status (RUN, ERR), timer, and voltage (V).
  • It also features a fault display for up to 25 fault codes.

6.2 Wireless Remote Control

  • The remote control allows for wireless operation within a range of up to 80 meters (or 150 meters, depending on environment).
  • Features include temperature adjustment, remote control start, and display of current water temperature.
  • The remote control has 4 keys for operation.
  • Supports voice announcement in Chinese, English, and Russian.
  • Includes a timer switch and auto-start switch functions.
Image showing remote control in use with a vehicle in a snowy environment
Pre-heating your car with digital control, effective within 80 meters.

6.3 Automatic Temperature Control

The heater features automatic temperature control for energy saving and fuel efficiency. Once the set temperature (e.g., 45°C-85°C) is reached, the machine automatically downshifts to maintain the temperature and save fuel.

Graph illustrating automatic temperature control and fuel consumption
Automatic temperature control mechanism for fuel efficiency.

6.4 Working Modes

The heater supports two primary working modes:

  • Air Condition Mode: For general air circulation.
  • Heater Mode: For active heating of the coolant and vehicle interior.

7. Troubleshooting

The LCD switch provides a fault display with up to 25 fault codes. If an error occurs, check the display for a code and refer to the full manual (if available) or contact customer support for specific diagnostic steps.

Common issues and checks:

  • No Heat/Insufficient Heat:
    • Check fuel level and quality. Ensure correct fuel type for ambient temperature.
    • Verify all fuel lines are clear and free of blockages or leaks.
    • Ensure coolant levels are adequate and circulating properly.
    • Check electrical connections for secure fit and proper voltage (9V-16V).
  • Unit Not Starting:
    • Confirm power supply is connected and providing 12V.
    • Check remote control battery and range.
    • Look for any fault codes on the LCD display.
  • Unusual Noise:
    • Ensure the unit is securely mounted and not vibrating against other components.
    • Check for any foreign objects in the air intake or exhaust.
Images depicting common winter driving issues the heater helps resolve
The heater helps resolve issues like battery life loss, difficult starts, ice/frost, and discomfort during parking rests.

8. User Tips

  • Fuel Type: The heater is compatible with both gasoline and diesel. Ensure you use the correct fuel type for your vehicle and local climate. Do not mix fuel types without completely emptying the tank first.
  • Remote Control Size: The remote control is compact and designed for portability, typically smaller than the main heater unit itself for ease of handling.
  • Water Heating: This unit is designed to heat the vehicle's coolant system. For optimal performance and to prevent damage, it is recommended to use appropriate automotive coolant (e.g., glycol-based) rather than plain drinking water, especially in freezing conditions.

9. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt and product model information handy when contacting support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.