Bafang SR PA112

Contents

Bafang Pedal Assist Sensor SR PA112 User Manual

Model: SR PA112

Introduction

This manual provides instructions for the installation, operation, maintenance, and troubleshooting of the Bafang Pedal Assist Center Column Sensor, model SR PA112. This sensor is designed to integrate with electric bicycle systems to provide pedal assistance based on rider input.

Front view of the Bafang pedal assist sensor

Figure 1: Bafang Pedal Assist Sensor SR PA112

Setup and Installation

The Bafang SR PA112 is a bottom bracket type pedal assist sensor. Proper installation is crucial for optimal performance and safety. It is recommended that installation be performed by a qualified bicycle mechanic if you are unfamiliar with bottom bracket replacement.

Components Overview

The package typically includes the sensor unit (integrated into a bottom bracket), a connecting cable, and potentially mounting hardware (gears, bolts) depending on the specific kit.

Bafang pedal assist sensor alongside additional components like gears and bolts

Figure 2: Sensor unit and accompanying components

Installation Steps (General)

  1. Preparation: Ensure your bicycle's bottom bracket shell width is compatible (68mm for this model). Gather necessary tools, including a bottom bracket tool, crank puller, and wrenches.
  2. Remove Existing Components: Remove the bicycle cranks and the existing bottom bracket.
  3. Install Sensor Unit: Thread the Bafang SR PA112 sensor unit into the bicycle's bottom bracket shell. Ensure it is tightened to the manufacturer's specifications to prevent loosening during operation.
  4. Connect Wiring: Connect the sensor's cable to your e-bike controller. Pay close attention to the plug matching to ensure correct electrical connection. The connector is a multi-pin type.
  5. Detailed view of the sensor's multi-pin electrical connector

    Figure 3: Close-up of the sensor's electrical connector

  6. Reinstall Cranks: Reattach the bicycle cranks to the sensor's spindle.
  7. Test Functionality: Before riding, perform a static test to ensure the pedal assist system is functioning correctly.

Important: Pay attention to the matching of the plug during connection to avoid damage or malfunction.

Operating Instructions

The Bafang SR PA112 sensor operates by detecting the rotation of your bicycle's pedals. When you begin pedaling, the sensor sends a signal to your e-bike's motor controller, which then activates the motor to provide assistance. The level of assistance is typically controlled by your e-bike's display unit or throttle, not directly by the sensor itself.

  • Pedal to Activate: The system will only provide motor assistance when you are actively pedaling.
  • Cadence Sensing: This sensor measures your pedaling cadence (how fast you are pedaling) to provide a smooth and responsive assist.
  • System Integration: Ensure your e-bike controller is configured to recognize and utilize the Bafang PAS signal. Refer to your e-bike controller's manual for specific settings.

Maintenance

Regular maintenance helps ensure the longevity and reliable performance of your Bafang pedal assist sensor.

  • Keep Clean: Periodically clean the area around the bottom bracket and sensor to prevent dirt and debris buildup, which can interfere with sensor operation.
  • Check Connections: Ensure all electrical connections, especially the sensor cable to the controller, are secure and free from corrosion.
  • Inspect for Damage: Regularly check the sensor unit and cable for any signs of physical damage, such as cracks, frayed wires, or bent pins.
  • Avoid Water Immersion: While designed for outdoor use, avoid submerging the sensor or exposing it to high-pressure water jets, which can compromise its seals.

Troubleshooting

If you experience issues with your pedal assist system, consider the following troubleshooting steps:

ProblemPossible CauseSolution
No pedal assistLoose or disconnected sensor cable. Incorrect plug matching. Sensor misalignment. Controller issue.Check all cable connections, ensuring they are fully seated and correctly matched. Inspect the sensor for proper alignment within the bottom bracket. Consult your e-bike controller manual.
Intermittent assistPoor electrical connection. Damaged cable or sensor. Debris interfering with sensor.Verify cable connections are tight. Inspect cable for damage. Clean the sensor area.
Assist too strong/weak or unresponsiveController settings.Adjust pedal assist levels on your e-bike's display or through the controller settings.

If problems persist after attempting these solutions, contact your e-bike dealer or Bafang support.

Specifications

FeatureDetail
ModelSR PA112
TypePedal Assist Sensor (PAS), Cadence Sensor
Spindle Length127mm
Bottom Bracket Shell Width68mm
MaterialMetal
BrandBafang
Bafang pedal assist sensor with dimensions indicated: 68mm (bottom bracket width) and 127mm (spindle length)

Figure 4: Sensor dimensions (68mm BB, 127mm spindle)

Close-up of the Bafang sensor label, showing 'SR PA112', '127 (mm)', and '68 (BB)'

Figure 5: Sensor label with model and dimensions

User Tips

  • Cable Management: Securely route the sensor cable along your bike frame to prevent it from snagging or getting damaged during rides. Use zip ties or cable clips.
  • Water Protection: While the sensor is generally weather-resistant, adding a small amount of dielectric grease to the electrical connector can further protect against moisture ingress, especially if riding in wet conditions frequently.
  • Regular Checks: Periodically check the tightness of the bottom bracket cups and crank arms to ensure the sensor remains securely in place and functions accurately.

Warranty and Support

For warranty information, please refer to the terms and conditions provided by your retailer or the official Bafang website. Keep your proof of purchase for any warranty claims.

If you require technical assistance or have questions not covered in this manual, please contact the seller or Bafang customer support directly. Provide your product model (SR PA112) and any relevant details about your e-bike system when seeking support.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.