Dancing Wings Hobby F25 AION-25

Contents

F25 Electric Sport Glider Balsawood KIT 2500mm AION-25 User Manual

Model: F25 AION-25 | Brand: Dancing Wings Hobby

1. Introduction

This manual provides essential information for the assembly, operation, and maintenance of your F25 Electric Sport Glider Balsawood KIT 2500mm AION-25. Please read this manual thoroughly before beginning assembly or operation to ensure safe and correct use of the product.

Warning: Not suitable for children under 14 years due to the nature of assembly and operation of RC models. Adult supervision is required for minors.

2. Product Overview

The F25 AION-25 is a 2500mm wingspan electric sport glider designed for intermediate to expert pilots. This is a balsawood kit, meaning it requires full assembly and additional electronic components (motor, ESC, servos, battery, receiver, remote control) to be purchased separately.

F25 2.5M AION Glider Specifications Overview
Figure 2.1: F25 2.5M AION Glider Specifications Overview. This image details the wingspan, length, flying weight, and recommended electronic components.
F25 Glider on Ground
Figure 2.2: Assembled F25 AION-25 Glider on the ground.

3. Assembly Instructions

The F25 AION-25 is supplied as an unassembled balsawood kit. This section outlines the general steps for assembly. Detailed step-by-step instructions are typically provided within the kit packaging or via a separate manual from the manufacturer. Always refer to the specific instructions included with your kit.

3.1 Required Tools and Materials (Not Included)

  • Hobby knife or razor blade
  • Sanding paper (various grits)
  • Wood glue (e.g., CA glue, epoxy, or wood glue suitable for balsa)
  • Covering film (if not included in your specific kit variant)
  • Heat iron or heat gun for covering film application
  • Small hand tools (pliers, screwdrivers)
  • Soldering iron and solder (for electronics)
  • Measuring tools (ruler, protractor)
  • Motor: MM2216 900-1100KV Brushless Motor
  • ESC: 20-30A Electronic Speed Controller
  • Servos: 6x 9g Servos (metal gear recommended)
  • Battery: 3S LiPo 2200-2800mAh
  • Propeller: 10-11 inch folding propeller
  • Receiver: ≥6 Channel Receiver
  • Remote Control: Compatible 6+ Channel Transmitter (MODE2)
F2501 AION KIT Components
Figure 3.1: F2501 AION KIT showing balsawood parts and decals. Other kit variants may include covering film or electronics.
Isometric Line Drawing of F25 Glider
Figure 3.2: Isometric view of the F25 Glider structure for assembly reference.
Top-Down Line Drawing of F25 Glider
Figure 3.3: Top-down view of the F25 Glider structure for assembly reference.

3.3 General Assembly Steps

  1. Inspect Components: Carefully check all balsawood parts for damage or warping.
  2. Wing Assembly: Assemble the wing sections according to the kit plans, ensuring proper dihedral and alignment. Install servos for ailerons/flaps.
  3. Fuselage Assembly: Construct the fuselage, integrating the motor mount, battery tray, and servo mounts for rudder and elevator.
  4. Tail Assembly: Assemble the horizontal and vertical stabilizers.
  5. Joining Sections: Attach the wing to the fuselage, and the tail sections to the rear of the fuselage.
  6. Electronics Installation: Install the motor, ESC, servos, receiver, and route all wiring. Ensure all connections are secure and correct.
  7. Control Linkages: Connect servos to control surfaces (ailerons, elevator, rudder) using appropriate linkages. Check for free movement and correct throw.
  8. Covering (if applicable): Apply the covering film to the airframe using a heat iron or heat gun, ensuring a smooth, taut finish.
  9. Decals: Apply any included decals as desired.
  10. Center of Gravity (CG): Crucially, balance the glider to the recommended Center of Gravity (CG) point specified in your kit's detailed instructions. This usually involves adjusting battery placement.
  11. Radio Setup: Bind your receiver to your transmitter. Configure control surface throws, exponential, and any mixing (e.g., flaperons) on your transmitter. Perform a range check.

4. Operating Instructions

4.1 Pre-Flight Checks

  • Ensure all control surfaces move freely and in the correct direction relative to stick inputs.
  • Check battery voltage on both the flight battery and transmitter battery.
  • Verify all connections are secure (motor, ESC, servos, receiver).
  • Confirm the Center of Gravity (CG) is correct.
  • Perform a range check of your radio system.
  • Check for any loose parts or damage to the airframe.

4.2 Launching

The F25 AION-25 is typically hand-launched. Ensure you have ample clear space and no obstacles downwind.

  1. Hold the glider firmly by the fuselage, slightly ahead of the CG.
  2. Apply about 70-80% throttle.
  3. Launch the glider with a firm, level throw directly into the wind. Do not throw upwards sharply.
  4. Immediately gain altitude and establish a gentle climb.
F25 Glider Hand Launch
Figure 4.1: Example of hand-launching the F25 AION-25 Glider.

4.3 Flight Control

Control is achieved via a 6-channel (or more) radio system:

  • Throttle: Controls motor speed for climb and powered flight.
  • Ailerons: Controls roll for turning.
  • Elevator: Controls pitch for climbing and descending.
  • Rudder: Controls yaw for coordinated turns and ground steering (if applicable).
  • Flaps (if configured): Can be used for slower flight or landing approaches.
F25 Glider in Flight
Figure 4.2: The F25 AION-25 Glider in stable flight.

4.4 Landing

Approach into the wind. Reduce throttle and manage altitude with the elevator. Use ailerons for directional control. If equipped with flaps, deploy them gradually to slow down for a gentle touchdown.

5. Maintenance

  • Post-Flight Inspection: After each flight, check the airframe for any damage, loose connections, or signs of stress.
  • Balsawood Care: Balsawood is delicate. Repair any cracks or breaks immediately using appropriate wood glue.
  • Covering Film: Inspect the covering film for wrinkles or tears. Re-tighten with a heat iron on low heat if necessary, or patch tears.
  • Electronics: Ensure all wires are securely connected and free from abrasion. Check servo operation and linkages.
  • Battery Care: Follow LiPo battery safety guidelines for charging, discharging, and storage.
  • Storage: Store the glider in a cool, dry place, away from direct sunlight and extreme temperatures, to prevent warping of the balsawood.

6. Troubleshooting

Problem Possible Cause Solution
Glider does not respond to controls.
  • Transmitter/receiver not bound.
  • Low transmitter/receiver battery.
  • Damaged receiver or servo.
  • Re-bind transmitter and receiver.
  • Charge/replace batteries.
  • Inspect and replace faulty components.
Motor not spinning.
  • Disconnected motor/ESC wires.
  • Faulty ESC or motor.
  • Low flight battery.
  • Check and secure all connections.
  • Test ESC/motor with known good components.
  • Charge/replace flight battery.
Glider flies erratically or is hard to control.
  • Incorrect Center of Gravity (CG).
  • Control surfaces trimmed incorrectly.
  • Warped wing or tail surfaces.
  • Loose control linkages.
  • Adjust CG by moving battery.
  • Adjust trims on transmitter.
  • Carefully straighten warped parts or replace.
  • Secure linkages.

7. Specifications

Feature Detail
Model NumberF25
TypeAirplane (Glider)
MaterialWood (Balsawood)
Wingspan2500mm
Length1255mm
Takeoff Weight / Flying WeightApprox. 1100g
State of AssemblyUnassembled Kit
Power SourceElectric
Recommended MotorMM2216 900-1100KV
Recommended ESC20-30A
Recommended Servos6x 9g (metal gear)
Recommended LiPo Battery3S 2200-2800mAh
Recommended Propeller10-11 inch folding
Control Channels≥6 channels
Controller ModeMODE2
Remote ControlYes (self-provided)
Is Batteries IncludedNo
Flight Time<5 minutes (powered flight, depends on battery/throttle)
Indoor/Outdoor UseOutdoor
Operator Skill LevelBeginner, Intermediate, Expert
Recommended Age14+ years
Package IncludesOriginal Box (Kit components)

8. User Tips

  • Patience with Assembly: Balsawood kits require patience and precision. Take your time with each step, especially gluing and sanding, for the best flight performance.
  • Covering Technique: If applying covering film, practice on scrap pieces first to master the technique for a smooth, wrinkle-free finish.
  • CG is Key: Double-check your Center of Gravity (CG) before the first flight. An incorrect CG is a common cause of poor flight characteristics or crashes.
  • Start with Low Rates: For initial flights, set your transmitter's control surface throws to lower rates to make the glider less sensitive and easier to control.
  • Fly in Calm Conditions: Especially for maiden flights, choose a day with minimal wind to reduce the risk of damage and make learning easier.
  • Seek Experienced Help: If you are new to RC gliders or balsawood kits, consider seeking assistance from an experienced RC pilot or club member for assembly and first flights.

9. Warranty and Support

For any issues regarding missing parts, manufacturing defects, or technical support, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.