1. Introduction
The BRIGHTWIN XH300 Auto Signal Generator is a third-generation automotive diagnostic tool designed to simulate various sensor signals for testing and troubleshooting vehicle electronic control units (ECUs) and related components. It provides precise simulation of crankshaft position (CKP), Hall, magnetoelectric, vehicle speed, and ABS sensor signals, enabling technicians to efficiently diagnose and repair automotive electrical systems.
2. Product Features
- Crankshaft Position Sensor Signal Simulation: Includes 9 types of gear missing teeth signals (58+2, 58+1, 57+2, 57+1, 37+1, 36+2, 35+1, 34+2, 22+1) and one standard 60+0 signal.
- Hall and Magnetoelectric Signal Output: Simultaneous output of both signal types.
- Adjustable Signal Amplitude: Output amplitude/peak voltage equals power supply input and can be adjusted via a potentiometer.
- Vehicle Speed Sensor Signal Simulation: Utilizes the 60+0 signal to simulate vehicle speed.
- Camshaft Sensor Signal Simulation: Supports 4+1 and 6+1 camshaft signals.
- Odometer/Speed Meter Testing: Can drive odometers and speed meters for testing.
- ABS Sensor and Optical Sensor Signal Simulation: Aids in analyzing and inspecting sensor errors, ECU malfunctions, and meter inaccuracies.
- User-Editable Crankshaft Signals: Allows users to edit and automatically save custom crankshaft signals.
- Single-Phase One-Key Reversal: Easy signal phase reversal with a dedicated button.
- Wide Frequency Range: 1Hz to 8KHz.
- Adjustable Signal Amplitude: 5V and 12V options.
- Broad Power Supply Input: 12-24V DC.
3. Package Contents
Please check the package for the following items:
- 1 x XH300 Auto Signal Generator (Host)
- 2 x Plugs
- 2 x Alligator Clip Cables
- 1 x Power Cord
- 1 x User Manual (this document)

4. Setup
The XH300 Auto Signal Generator requires an external DC 12-24V power supply to operate. Ensure all connections are secure before powering on the device.
4.1 Device Overview and Connections

Refer to Figure 4.1 for the layout of the device. Key connection points include:
- Power Input (DC12-24V): Connect the provided power cord to this input.
- Hall Signal Output: For Hall effect sensor simulations.
- Magnetoelectric Output: For magnetoelectric sensor simulations.
- Signal Amplitude Selection (12V/5V): Switch to select the desired output amplitude.
5. Operation
The XH300 allows for simulation of various automotive signals. The signal frequency is displayed in Hertz (Hz) by default.
5.1 General Controls
- SET Key: Short press to select signal type. Long press to enter editing mode for CKP signals.
- Up/Down Buttons: Adjust signal frequency/speed or edit parameters in editing mode.
- H/L (Phase Reversal) Key: Press to reverse the signal phase by 180 degrees. The display will show 'H' for high waveform or 'L' for low waveform.
5.2 Engine Crankshaft Position Sensor (CKP) / Engine Speed Sensor Simulation
The instrument has six commonly used crankshaft signals stored: 58+2, 34+2, 36+2, 60+0, 56+4, and 10+1. Additionally, two camshaft signals (4+1 and 6+1) are built-in.
- Short press the SET key to select the desired crankshaft signal type.
- Use the Up and Down keys to adjust the signal frequency (engine speed).

5.2.1 Editing Crankshaft Missing Tooth Signals
The 10+1 signal is editable. If other types of crankshaft signals are needed, they can be edited and saved.
- Long press the SET key to enter the signal editing mode. The two digits on the left (number of teeth) will blink.
- Press the Up or Down key to modify the number of teeth (range 1-99).
- Short press the SET key. The digit for missing teeth will blink.
- Press the Up or Down key to modify the number of missing teeth (range 1-9).
- Short press the SET key again to exit the editing mode. The newly edited signal is automatically saved over 56+4, overwriting the original 10+1 signal.

5.3 Vehicle Speed Sensor (Odometer Signal) Simulation
There are two ways to collect vehicle speed signals: from a separate speed sensor on the transmission output shaft (common in trucks and motorcycles) or from an ABS sensor (common in small cars).
- Distinguish the acquisition method: separate speed sensor or shared sensor with ABS.
- Distinguish sensor type: magnetoelectric, three-wire Hall, or two-wire Hall. The XH300 can simulate magnetoelectric and three-wire Hall signals, but does not support two-wire Hall.
- Short press the SET key and select signal type 60+0 (no lack of tooth signal).
- Press the Up or Down key to adjust the signal frequency, which simulates the vehicle speed.
For connection methods, refer to the crankshaft position sensor diagrams.

Video 5.1: Demonstration of Vehicle Speed Signal Simulation using XH300.
5.4 Magnetoelectric ABS Sensor Signal Simulation
ABS sensors can be either Hall type or magnetoelectric type. The XH300 can simulate magnetoelectric ABS sensor signals. It does not support two-wire Hall type ABS sensors.

5.5 ECU Testing
The XH300 can be used in conjunction with other diagnostic tools (e.g., PD60+ Fuel Injector and Ignition Simulator) to test ECUs by providing simulated engine speed signals.


5.6 Waveform Output
The XH300 generates various waveforms for different sensor types. Below are examples of the waveform outputs:

6. Specifications
| Attribute | Value |
|---|---|
| Model Number | XH300 |
| Brand Name | BRIGHTWIN |
| DIY Supplies | Electrical |
| Origin | Mainland China |
| Certification | CE, RoHS |
| Display Size | 3.0 - 4.9 Inches |
| Output Frequency | 1Hz - 8KHz |
| Signal Amplitude | 5V, 12V (Adjustable) |
| Signal Type | Hall, Magnetoelectric |
| Power Supply Input | 12-24V DC |
| Function | Auto Signal Generator |
| Battery Included | No |
| High-concerned chemical | None |
| Dimensions (approx.) | 110mm (L) x 80mm (W) x 27mm (H) |
| Weight (approx.) | 0.35 kg |

7. Maintenance
To ensure the longevity and optimal performance of your XH300 Auto Signal Generator, follow these maintenance guidelines:
- Keep the device clean and free from dust and debris. Use a soft, dry cloth for cleaning.
- Avoid exposing the device to extreme temperatures, humidity, or direct sunlight.
- Store the device in a safe place when not in use, preferably in its original packaging or a protective case.
- Do not attempt to open or repair the device yourself, as this may void the warranty and cause damage.
8. Troubleshooting
If you encounter issues with your XH300 Auto Signal Generator, please refer to the following common troubleshooting steps:
- No Power: Ensure the DC 12-24V power supply is correctly connected and providing adequate power. Check the power cord and connections for any damage.
- Incorrect Signal Output: Verify that the correct signal type has been selected using the SET key. If editing a CKP signal, ensure the editing process was completed and saved correctly.
- Signal Not Recognized by ECU/Meter: Confirm that the connection to the ECU or meter is correct and secure. Ensure the signal amplitude (5V/12V) is appropriate for the component being tested.
- Signal Configuration: The generated signals are generally standardized. However, for CKP signals, you can configure specific parameters (number of teeth, missing teeth) as described in Section 5.2.1.
If the problem persists, contact customer support for further assistance.
9. User Tips
- Always ensure an external DC 12-24V power supply is connected before operating the device.
- This product is specialized equipment for automotive maintenance. Non-professional personnel should use it under the guidance of qualified auto repair technicians.
- When simulating vehicle speed signals, correctly identify whether the vehicle uses a separate speed sensor or an ABS sensor for signal acquisition, and the type of Hall sensor (three-wire vs. two-wire).
10. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the seller's official website or contact their customer service department. Keep your purchase receipt as proof of purchase.