Beitian BN-180, BN-220, BN-280, BN-800, BN-880

Contents

Beitian GPS Module Series User Manual

Models: BN-180, BN-220, BN-280, BN-800, BN-880

1. Introduction

This manual provides essential information for the Beitian series of GPS modules, including models BN-180, BN-220, BN-280, BN-800, and BN-880. These modules are designed for use with RC drones and flight controllers such as CC3D, F3, Pixhawk, and APM. Please read this manual carefully before use and keep it for future reference.

Product Overview Video

This video provides a visual overview of the Beitian GPS modules, showcasing different models and their physical characteristics.

2. Safety & Warnings

WARNING: To reduce the risk of injury, fire, electric shock, or property damage, please read and follow all safety information and instructions before using this product.

  • This product is intended for users aged 14 years and above.
  • Not suitable for children under 3 years. Small parts may present a choking hazard.
  • Keep away from fire, high temperature, water, moisture, and corrosive environments.
  • Do not disassemble, modify, or repair the product without authorization.
  • Use the product only for its intended purpose. Misuse may cause injury or damage.
  • If the product is damaged, overheated, emits smoke, unusual odor, or noise, stop using it immediately and contact support.
  • Keep packaging materials (plastic bags, foam, etc.) away from children to avoid suffocation risk.
  • For indoor use only unless otherwise specified on the product or packaging.

3. Setup Instructions

3.1 Preparation

  • Carefully remove all protective films or packaging materials from the GPS module and any included cables.
  • Ensure you have the necessary flight controller (e.g., CC3D, F3, Pixhawk, APM) and power source (typically 5V) for your setup.

3.2 Wiring and Connection

Connect the GPS module to your flight controller using the provided cable. Refer to the specific pinout diagrams for your module model (BN-180, BN-220, BN-280, BN-880) to ensure correct connections. Incorrect wiring can damage the module or flight controller.

BN-180 / BN-220 Pin Description

Pin description for Beitian BN-180 and BN-220 GPS modules, showing GND, TX, RX, and VCC pins.
Figure 1: Pinout for BN-180 and BN-220 GPS modules.
PINPIN NameI/ODescription
1GNDGGround
2TXOSerial Data Output.
3RXISerial Data Input.
4VCCIDC 3.0V - 5.5V supply input, Typical: 5.0V

BN-280 Pin Description

Pin description for Beitian BN-280 GPS module, showing 1PPS, GND, TX, RX, VCC, and BOOT pins.
Figure 2: Pinout for BN-280 GPS module.
PINPIN NameI/ODescription
11PPSO1 Pulse Per Second when 3D fixed
2GNDGGround
3TXOSerial Data Output.
4RXISerial Data Input.
5VCCIDC 3.0V - 5.5V supply input, Typical: 5.0V
6BOOTIN.C. (Not Connected)

BN-880 Pin Description

Pin description for Beitian BN-880 GPS module, showing SDA, GND, TX, RX, VCC, and SCL pins for compass functionality.
Figure 3: Pinout for BN-880 GPS module.
PINPIN NameI/ODescription
1SDAOCompass SDA
2GNDGGround
3TXOSerial Data Output.
4RXISerial Data Input.
5VCCI3.0V~5.5V supply input, Typical: 5.0V
6SCLICompass SCL

Ensure all connections are secure before applying power. Refer to your flight controller's documentation for specific GPS port configurations.

4. Operating Instructions

4.1 Power On

  • Apply power to your flight controller setup. The GPS module will power on automatically.
  • Observe the LED indicators on the GPS module:
    • TX LED (Blue): Indicates data output. It will flash when data is being transmitted.
    • PPS LED (Red): Indicates GPS fix status. It will not be bright when GPS is not fixed, and will flash when a 3D fix is achieved.

4.2 GPS Signal Acquisition

  • Place your RC drone or flight controller in an open area with a clear view of the sky to facilitate faster GPS signal acquisition.
  • The module will begin searching for satellites. This process may take several minutes, especially during the first use or after a long period of inactivity.
  • Once a sufficient number of satellites are found and a 3D fix is established, the PPS LED will start flashing.

4.3 Integration with Flight Controller Software

Configure your flight controller's software (e.g., Betaflight, ArduPilot, iNav) to recognize and utilize the connected GPS module. This typically involves:

  • Enabling the GPS feature in the flight controller's configuration.
  • Setting the correct UART port and baud rate for the GPS module.
  • Selecting the appropriate GPS protocol (e.g., UBLOX, NMEA).
  • Calibrating the compass (for modules with integrated compass like BN-800, BN-880) according to your flight controller's instructions.

4.4 After Use

After completing your flight or operation, power down your RC drone or flight controller. It is generally not necessary to physically unplug the GPS module unless performing maintenance or storage.

5. Maintenance & Storage

5.1 Cleaning

  • Ensure the GPS module is powered off and disconnected from any power source before cleaning.
  • Use a soft, lint-free cloth to gently wipe the module.
  • Do not use harsh chemicals, abrasive materials, or excessive moisture, as these can damage the electronic components.

5.2 Storage

  • Store the GPS module in a dry place at room temperature (15°C - 35°C).
  • Keep it away from direct sunlight, high humidity, and extreme temperatures.
  • Protect the module from physical impact and static discharge.

6. Troubleshooting

If you encounter issues with your Beitian GPS module, consider the following common troubleshooting steps:

  • No GPS Fix (PPS LED not flashing):
    • Ensure the module has a clear view of the sky.
    • Verify all wiring connections (VCC, GND, TX, RX) are correct and secure.
    • Check the power supply voltage to the module (should be 3.0V-5.5V, typically 5.0V).
    • Confirm the flight controller software is configured correctly for the GPS module (UART port, baud rate, protocol).
  • Incorrect Data / No Data (TX LED not flashing):
    • Double-check TX/RX connections between the GPS module and flight controller. They should be cross-connected (GPS TX to FC RX, GPS RX to FC TX).
    • Verify the baud rate setting in the flight controller matches the GPS module's default or configured baud rate.
  • Compass Issues (for BN-800/BN-880):
    • Ensure SDA and SCL lines are correctly connected.
    • Perform a compass calibration in your flight controller software.
    • Keep the module away from strong magnetic fields or ferrous materials.
  • Module Not Powering On:
    • Check VCC and GND connections.
    • Test the power source.

If these steps do not resolve the issue, please refer to the "Warranty & Support" section for further assistance.

7. Technical Specifications

FeatureDetails
Brand NameBeitian (wishiot)
Model NumbersBN-180, BN-220, BN-280, BN-800, BN-880 (FZ2917, FZ2918, FZ3017, FZ2920)
ChipU-blox M8030
Input Voltage (VCC)DC 3.0V - 5.5V (Typical: 5.0V)
Rated Power≤5W
MaterialComposite Material
Operating Temperature-10°C ~ 40°C
Recommended Age14+y
UseVehicles & Remote Control Toys (For CC3D F3 Flight Controller Pixhawk APM)
Packing ListGPS module + cable
Dimensions (BN-880)28.0mm x 28.0mm x 10.0mm

7.1 Module Feature Comparison

Table comparing Beitian GPS module types by chip, antenna type, flash memory, and compass presence.
Figure 4: Comparison of Beitian GPS module features.
TypeChipAntenna TypeFlashCompass
BN-180U-blox M8030PassiveNONO
BN-220U-blox M8030PassiveYESNO
BN-280U-blox M8030PassiveYESNO
BN-800U-blox M8030PassiveYESYES
BN-808U-blox M8030PassiveNONO
BN-880U-blox M8030ActiveYESYES

8. User Tips

  • Mounting: For optimal performance, mount the GPS module as far away as possible from other electronic components that might generate electromagnetic interference, such as VTX (video transmitters) or ESCs (electronic speed controllers).
  • Orientation: Ensure the GPS module is mounted with the antenna facing upwards and with a clear, unobstructed view of the sky.
  • Initial Fix: The first GPS fix can take longer. Be patient and ensure the module is in an open outdoor area. Subsequent fixes will typically be much faster.
  • Compass Calibration: If your module has a compass (BN-800, BN-880), regular calibration is crucial for accurate heading information, especially after moving the module or changing its orientation.

9. Warranty & Support

If you encounter any problems such as product damage, missing parts, or require technical assistance, please contact customer support through the following channels:

  • AliExpress Order Chat Window: Contact us directly through your order page on AliExpress.
  • WhatsApp Support: +86 19937531992
  • Email Support: info@unikelc.com (We will reply to you as soon as possible.)

For additional detailed information, you may also refer to the official user manual PDF available here.

10. Disposal & Recycling

This symbol indicates that this product should not be treated as household waste.

According to the WEEE Directive (2012/19/EU), it must be disposed of at an appropriate electronic waste collection point for recycling to prevent potential negative consequences for the environment and human health.

Dispose of packaging materials responsibly. Recycle paper, cardboard, and plastic where facilities exist.

Protect our environment. Thank you for your cooperation.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.