Hobbywing 30L Pump 18S

Contents

Hobbywing 30L Pump 18S Instruction Manual

Model: 30L Pump 18S (Combo-pump-30L-18S)

1. Introduction

This manual provides essential information for the safe and efficient operation, installation, and maintenance of your Hobbywing 30L Pump 18S. This electrical rubber flexible impeller water pump diaphragm is designed for agricultural drone applications, featuring an IP66 ingress protection rating and compatibility with 12S-18S Li-Po batteries. Please read this manual thoroughly before using the product.

Hobbywing 30L Pump 18S main product image
Figure 1: Hobbywing 30L Pump 18S

2. Safety Warnings

  • Always ensure the pump is disconnected from power before installation, maintenance, or troubleshooting.
  • Operate the pump within the specified voltage range (12S-18S Li-Po) to prevent damage.
  • Ensure all connections are secure and waterproof, especially given the IP66 rating.
  • Do not operate the pump dry for extended periods.
  • Keep hands and loose clothing away from moving parts during operation.
  • This product is intended for use with agricultural drones. Do not use for purposes other than its intended application.
  • WARNING: This product can expose you to chemicals including phthalates (DEHP), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

3. Setup and Installation

3.1 Component Overview

Disassembled view of the Hobbywing 30L Pump
Figure 2: Disassembled view of the pump, showing main components.
Another disassembled view of the Hobbywing 30L Pump
Figure 3: Exploded view of the pump assembly.

3.2 Mounting the Pump

  • Mount the pump securely to the drone frame using appropriate hardware. Refer to the CAD drawing for mounting dimensions.
  • Ensure the pump is positioned to allow for proper water inlet and outlet connections without kinking hoses.
CAD drawing with dimensions and wiring diagram for Hobbywing 30L Pump
Figure 4: CAD drawing showing pump dimensions and wiring details.

3.3 Water Pipe Connection

  • The inlet and outlet outer diameter is 20.53mm. It is recommended to use water pipes with an inner diameter of 19mm for optimal fit and performance.
  • Secure all water pipe connections with clamps to prevent leaks.

3.4 Electrical Wiring

Connect the pump to your drone's power and control system according to the pin definitions below. Ensure correct polarity and secure connections.

Table 1: Power Cable Connector Pin Definition
Pin Harness ColorPin Definition
RedPower+
PurpleThrottle/TS
BlackPower Ground
BlueCAN-H
GreenCAN-L
  • The pump is compatible with 12S-18S Li-Po batteries. Ensure your power source matches this requirement.
  • The control mode supports both PWM and CAN. Connect the appropriate control lines based on your drone's flight controller.

4. Operating Instructions

4.1 Pre-Operation Checklist

  • Verify all electrical connections are secure and insulated.
  • Confirm water pipes are correctly attached and free from kinks or blockages.
  • Ensure the water tank contains sufficient liquid for pumping.
  • Check that the battery voltage is within the 12S-18S range.

4.2 Starting the Pump

  • Power on your drone system.
  • Control the pump via PWM or CAN signals from your flight controller. The throttle range is fixed at 1050-1950 μs.
  • Note that throttle calibration is not supported for this pump.
  • Observe the pump's operation to ensure smooth flow and no unusual noises or vibrations.

4.3 Stopping the Pump

  • Reduce the throttle signal to the minimum or send a stop command via CAN.
  • Power off the drone system after use.

5. Maintenance

5.1 Regular Checks

  • Inspect water pipes and connections for wear, damage, or leaks before each use.
  • Check electrical wiring for any signs of fraying or corrosion.
  • Ensure the pump's exterior is clean and free from debris.

5.2 Cleaning

  • After use, especially with agricultural chemicals, flush the pump with clean water to prevent residue buildup.
  • Wipe down the exterior with a damp cloth. Do not use harsh chemicals that could damage the composite material or rubber components.

5.3 Storage

  • Store the pump in a dry environment with temperatures between -10℃ and 50℃.
  • Ensure storage humidity is ≤85%.
  • Protect the pump from direct sunlight and extreme temperatures.

6. Troubleshooting

Table 2: Common Troubleshooting Guide
ProblemPossible CauseSolution
Pump does not startNo power; Incorrect wiring; Faulty ESC/controller signalCheck battery connection and voltage; Verify wiring against diagram; Test ESC/controller output.
Low or no water flowEmpty tank; Kinked or blocked hose; Air in the system; Impeller damageRefill tank; Inspect and clear hoses; Prime the pump if necessary; Inspect impeller for damage.
Water leakageLoose pipe connections; Damaged seals/hosesTighten hose clamps; Inspect and replace damaged pipes or seals.
Unusual noise/vibrationDebris in pump; Loose mounting; Worn bearingsDisconnect power and inspect pump for foreign objects; Ensure pump is securely mounted; Contact support if noise persists.

7. Specifications

Tables showing System, ESC, Environmental Adaptability, and Performance specifications for the pump
Figure 5: Detailed specifications including system parameters, ESC parameters, environmental adaptability, and performance curve.
Table 3: General Specifications
ParameterValue
Product ModelCombo-pump-30L-18S
MaterialComposite Material
Total Weight516g
Size (L*W*H)91*110*67mm
Recommended Battery12S-18S (Li-Po)
Rated Flow20 L/min
Maximum Flow30 L/min
Rated Power80W
Maximum Power110W
Rated Current4A
Max Current10A
Compatible Voltage12S-18S
Operating Temperature0~50℃
Ingress ProtectionIP66
Inlet & Outlet Outer Diameter20.53mm (Recommend water pipe inner diameter 19mm)
Cable180mm Teflon-6 cable and male connector (GND-yellow, S(PWM)-purple, CH-blue, CL-green, +-red, GND-black)
Table 4: ESC Parameters (XRotor-10A-FOC)
ParameterValue
ESC ModelXRotor-10A-FOC
PWM High Level3.3V/5V
Throttle (μs)Fixed 1050-1950
Throttle CalibrationNonsupport
Frequency50-500Hz
Communication MethodCAN
Control ModePWM+CAN
Continuous Current4A
Instantaneous Current10A
Controller CAN ResistanceNo
PCB Hardware Version (CAN-ESC)PCB-HW5116_YT1_V1.2
ESC-Driver Firmware (CAN-ESC)HW5116_KZ1_V1_C04TG4517S100Z-20246061
CAN Communication VersionCAN-04.1.13
CAN Communication ProtocolUAVCAN(HWCAN)
Table 5: Environmental Adaptability & Lifespan Requirements
ItemParameter
NSS Salt Spray Test72h
Ingress ProtectionIP66
Operating Temperature0~50℃
Operating Humidity5%~95%
Storage Temperature-10~50℃
Storage Humidity≤85%

7.1 Performance Data

Flow-RPM curve graph for the Hobbywing 30L Pump
Figure 6: Flow-RPM curve illustrating pump performance.

The Flow-RPM curve (Figure 6) provides a visual representation of the pump's flow rate (L/min) across different RPMs, indicating its performance characteristics.

8. User Tips

  • Voltage Consistency: Always ensure your battery voltage is stable and within the 12S-18S range to prevent pump damage and ensure consistent performance.
  • Pipe Sizing: Using the recommended 19mm inner diameter water pipes will optimize flow and reduce strain on the pump.
  • Pre-Flight Check: Before each flight, quickly check all hose connections for tightness and ensure there are no visible leaks.
  • Post-Operation Flush: If using the pump for spraying chemicals, a thorough flush with clean water after each use can significantly extend the pump's lifespan and prevent chemical buildup.
  • Environmental Awareness: While the pump is IP66 rated, avoid prolonged exposure to extreme conditions outside the specified operating and storage temperatures.

9. Warranty and Support

For specific warranty terms and conditions, please refer to the documentation provided at the time of purchase or contact your retailer/manufacturer directly.

For technical support, troubleshooting assistance beyond this manual, or spare parts inquiries, please contact the official Hobbywing support channels or your authorized dealer.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.