NERIES Single Hall Booster Program Controller

Contents

NERIES Electric Bicycle Motor Controller Instruction Manual

Model: Single Hall Booster Program Controller

Brand: NERIES

1. Introduction

Thank you for choosing the NERIES Electric Bicycle Motor Controller. This controller is designed to provide efficient and reliable power management for your electric bicycle or scooter. It features intelligent design for steady speed control, sensitive braking, and direction changes. This product is specifically designed to work with single Hall sensors only.

NERIES Electric Bicycle Motor Controller
NERIES Electric Bicycle Motor Controller (Single Hall, 250W/350W, DC24-48V/DC36-60V)

2. Specifications

FeatureDetail
BrandNERIES
Model NameSingle Hall Booster Program Controller
Power250W / 350W
Voltage OptionsDC 24V-48V / DC 36V-60V
Current Limit13A
MaterialAluminum Alloy
Dimensions (L x W x H)8.81 cm x 5.2 cm x 2.93 cm
Weight186g
OriginMainland China
Brake DegreeLow
High-concerned chemicalNone
Controller dimensions
Controller dimensions: 8.81cm x 5.2cm x 2.93cm

3. Package Contents

  • 1 x NERIES Electric Bicycle Motor Controller

4. Safety Information

  • Always disconnect power before installation or maintenance.
  • Ensure all connections are secure and properly insulated to prevent short circuits.
  • Do not expose the controller to water or extreme temperatures.
  • This controller is designed for single Hall sensors only. Using it with other sensor types may cause damage.
  • Seek professional assistance if you are unsure about any installation steps.

5. Installation and Setup

Follow these general steps for installing your motor controller. Refer to the wiring diagram for specific connections.

  1. Mount the Controller: Securely mount the controller in a dry, protected location on your bicycle or scooter. The aluminum alloy casing helps with heat dissipation, so ensure adequate airflow if possible.
  2. Connect Power: Connect the main power positive electrode and power negative pole wires to your battery. Ensure correct polarity.
  3. Connect Motor: Connect the phase lines of your brushless motor to the corresponding wires on the controller.
  4. Connect Hall Sensor: Connect the motor's single Hall sensor wires to the 'Motor Hall' connector on the controller.
  5. Connect Throttle: Connect the 'Turn the handle' wires to your throttle.
  6. Connect Brake: Connect your brake levers to the 'Brake off' and 'Brake light socket' wires as applicable.
  7. Connect Main Electric Door Lock: Connect the main electric door lock wires.
  8. Connect Pulse Assist Sensor: If your e-bike has a pedal assist system (PAS), connect the 'Pulse Assist Sensor' wires.
  9. Intelligent Phase Recognition: The controller features intelligent phase recognition. After all connections are made, power on the system. The controller should automatically detect and match the motor phases.
  10. Test Functionality: Carefully test the throttle, brakes, and pedal assist (if applicable) before riding.

6. Wiring Diagram

The following diagram illustrates the various connections for the motor controller. Please match the wire colors and labels carefully during installation.

Electric Bicycle Motor Controller Wiring Diagram
Detailed wiring connections for the NERIES Motor Controller.

Wiring Key:

  • Power positive electrode: Main power input (positive)
  • Brake light socket: Connection for brake light
  • Main electric door lock: Ignition/power switch connection
  • Pulse Assist Sensor: Pedal Assist System (PAS) sensor input
  • Intelligent phase recognition: Wires for automatic motor phase detection
  • Cruise control: Connection for cruise control function
  • Brake off: Brake signal input (cuts motor power when activated)
  • Motor Hall: Hall sensor input from the motor
  • Power negative pole: Main power input (negative)
  • Phase line of brushless motor: Three main power wires to the motor
  • Turn the handle: Throttle input

7. Operating Instructions

Once installed and tested, the controller operates automatically based on your inputs:

  • Power On: Turn on your e-bike's main power switch (connected to the 'Main electric door lock').
  • Throttle Control: Use the 'Turn the handle' (throttle) to control the motor speed. The intelligent design ensures steady and responsive speed changes.
  • Braking: Activating the brakes will send a signal to the 'Brake off' connection, cutting power to the motor for safe stopping. If connected, the 'Brake light socket' will activate your brake light.
  • Pedal Assist (if applicable): If a 'Pulse Assist Sensor' is connected, the controller will provide motor assistance based on your pedaling input.
  • Cruise Control: If your system includes a cruise control switch connected to the 'Cruise control' wires, you can activate it to maintain a constant speed.

8. Troubleshooting

If you encounter issues with your motor controller, consider the following:

  • No Power: Check battery connections, main electric door lock, and ensure the battery is charged.
  • Motor Not Responding: Verify all motor phase wires and Hall sensor connections are secure. Ensure the motor is a brushless type with a single Hall sensor.
  • Erratic Operation: Recheck all wiring for loose connections or incorrect polarity. Ensure no wires are pinched or damaged.
  • Brakes Not Cutting Power: Inspect the 'Brake off' wiring and the brake lever switches.
  • Overheating: Ensure the controller is mounted in a location with adequate airflow and is not covered.

User Tips:

  • Always double-check the voltage compatibility (24-48V or 36-60V) before connecting to your battery.
  • Ensure your motor uses a single Hall sensor for proper operation with this controller.
  • For optimal performance and longevity, keep the controller clean and dry.

9. Maintenance

  • Regular Inspection: Periodically check all wiring connections for tightness and signs of wear or corrosion.
  • Cleaning: Keep the controller's exterior clean and free from dust and debris. Use a dry cloth; avoid liquids.
  • Environmental Protection: Ensure the controller remains protected from moisture and direct sunlight to prevent damage to internal components.
  • Heat Dissipation: Verify that the controller's mounting location allows for proper heat dissipation.

10. Warranty and Support

For warranty information, technical support, or any questions regarding your NERIES Electric Bicycle Motor Controller, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.