STEPPERONLINE DM420Y

Contents

STEPPERONLINE DM420Y Digital Stepper Motor Driver User Manual

Open Loop Stepper Driver

1. Introduction

Thank you for choosing the STEPPERONLINE DM420Y Digital Stepper Driver. This manual provides essential information for safe and effective use of the product. Please read it carefully before operation.

1.1 Product Overview

The DM420Y is a high-performance digital stepper driver utilizing a new generation of 32-bit DSP technology. It operates on a DC18-36V supply and is designed to drive two-phase hybrid stepper motors with external diameters of 20mm, 28mm, 35mm, and 42mm, with an adaptive peak current below 2.2A.

This driver incorporates a servo-like control principle, unique circuit design, and advanced software algorithms to ensure superior performance in terms of smoothness, reduced noise, and minimal vibration. Its precise current control technology significantly lowers motor heating. It supports 8-speed equal angle constant torque subdivision, up to 128 subdivisions, and features optocoupler isolated common positive signal input for strong anti-interference capabilities. The DM420Y also includes over-voltage, under-voltage, and other error protection functions.

1.2 Key Features

  • New generation 32-bit DSP control technology for high performance, stability, and reduced noise/vibration.
  • Optical coupling isolated common positive signal input for strong anti-interference.
  • Motor parameter identification function for optimal control.
  • Smooth and accurate current control, leading to lower motor heat.
  • Highest impulse response frequency up to 200KHz.
  • Motor current halves when stepping pulse stops for more than 200ms.
  • Input voltage range: DC18-36V.
  • Adjustable peak driving current below 2.2A.
  • Equipped with over-voltage, under-voltage, and other error protection.
  • Excellent stability in low frequency subdivision.

1.3 Application Field

The DM420Y is primarily used in medical equipment, dispensers, engraving machines, laser equipment, labeling machines, electronic equipment, advertising equipment, and other automation equipment. It is particularly effective in applications requiring low heat, low noise, low vibration, high stability, and high precision.

1.4 Safety Statement

Warning: Improper operations may result in personal injury or equipment damage. Always ensure correct wiring and adhere to specified voltage limits.

The design and manufacture of this product do not inherently protect personal safety from mechanical system threats. Users must implement safety protection measures in their mechanical system designs to prevent accidents from improper operation or abnormal product behavior.

Product improvements may lead to changes in this manual without notice. The company is not responsible for user modifications to the product.

2. Specifications

2.1 Electrical Characteristics

DM420Y Electrical Specifications
ArgumentMinimum valueTypical valueMaximum valueUnit
Continuous output current0-2.2A
Input supply voltage182436Vdc
Logic input current71020mA
Pulse frequency0-200kHz
Insulation resistance50--MΩ

2.2 Using Environment

DM420Y Operating Environment
Cooling ModeNatural Cooling
Use environmentUse occasionAvoid other heating equipment, dust, oil mist, corrosive gas, strong vibration, flammable gas, and conductive dust.
Temperature0℃ ~ 50℃
Humidity40 – 90%RH (non-condensation)
Vibration10 ~ 55Hz / 0.15mm
Storage temperature-20℃ ~ +70℃

2.3 Mechanical Specifications

The DM420Y driver has compact dimensions for easy integration.

DM420Y Mechanical Dimensions Diagram

Text Description for Mechanical Dimensions Diagram: The diagram shows the mechanical dimensions of the DM420Y driver. The overall length is 86mm, width is 55mm, and height is 21mm. Mounting holes are provided for secure installation.

2.4 General Properties

  • Power Supply: DC
  • Motor Type: DC Motor, Stepper Motor
  • Origin: Mainland China
  • Certification: CE
  • Control Modes: Pulse Mode
  • Input Voltage: 18 - 36VDC (Reference: 24 - 36VDC)
  • Max. Output Current RMS: 1.55A
  • No. of Phase: 2
  • Output Current: 0.3 - 2.2A
  • Max. Pulse Input: 100kHZ
  • Pulse Width: 5µs
  • Wireless Functionality: No
  • Battery Included: No
  • High-concerned chemical: None

3. Setup and Installation

3.1 Mounting Dimensions

The mounting dimensions are detailed in the mechanical specifications diagram above. Ensure adequate space for installation and cooling.

3.2 Installation Methods

For optimal heat dissipation, install the driver upright to facilitate strong air convection. If necessary, install a fan close to the driver to force heat dissipation. This ensures the driver operates within its reliable temperature range (typically below 50°C) and the motor within its operating temperature (typically below 80°C).

Vertical Mounting Diagram for Stepper Drivers

Text Description for Vertical Mounting Diagram: This diagram illustrates the recommended vertical mounting method for stepper drivers to ensure proper airflow and heat dissipation. It shows multiple stepper drivers mounted vertically with specified clearances (e.g., ≥50mm between drivers, ≥30mm from walls) to allow for air inlet at the bottom and air outlet at the top, promoting natural cooling.

3.3 Driver Ports and Wiring

Proper wiring is crucial for the correct operation of the DM420Y driver. Always ensure power is off before making any connections.

DM420Y Digital Stepper Driver Wiring Diagram and DIP Switch Settings

Text Description for Wiring Diagram and DIP Switch Settings: This image displays the top view of the DM420Y Digital Stepper Driver, clearly showing the terminal blocks for power input, motor connections, and control signals. It also features tables printed on the driver's casing for setting current (Peak, SW1, SW2, SW3) and pulse/revolution (Pulse/rev, SW5, SW6) using DIP switches. SW4 is designated for Half/Full Current setting (OFF=Half Current, ON=Full Current). The power input range is VDC: 18V-36V.

3.3.1 Port Definition

Control Signal Input Port
PortLeadSymbolFeatureAnnotation
1PUPulse signal photoelectric isolation negative endFalling edge is effective; motor moves one step per pulse. Pulse width > 2.5 microseconds.
2DRDirectional signal photoelectric isolation negative endUsed to change motor steering.
35V+Signal power supply has a total positive inputSignal input positive end, +5~24V input. For >24V, connect current limiting resistance.
4MFRelease signal photoelectric isolation negative endWhen effective, motor coil current is turned off, driver stops, motor is in free state.
Power Input and Motor Port
PortLeadSymbolNameFunction
1V-Power interfaceDC18-36V
2V+
3A+Motor interfaceTwo phase stepper motor connector
4A-
5B+
6B-

3.3.2 Input/Output Port Operation

The DM420Y driver features three digital inputs with photoelectric isolation, supporting 5V-24V input. If the input signal voltage exceeds 24V, a series current limiting resistor is required at the signal input end. The common positive connection diagram is shown below:

DM420Y Port Definition and Driver Status Indicators

Text Description for Port Definition and Driver Status Indicators: This image provides a detailed view of the DM420Y driver's port definitions and status indicators. It includes a table for 'Port Definition' listing Pin Name (PU, DR, MF, 5V+) and their details, such as pulse validity, motor direction change, and driver release. Below this, there's a table for 'Driver Status Indicators' explaining fault information (Overcurrent, Overvoltage, Power supply voltage too low), corresponding ALM light flashes, and resetting methods.

3.3.3 Signal Input Timing Diagram

To prevent abnormal operation of the driver control motor, adhere to the following timing diagram for input signals:

DM420Y Signal Input Timing Diagram

Text Description for Signal Input Timing Diagram: The diagram illustrates the timing requirements for the PU (Pulse), DR (Direction), and MF (Release) signals. It shows that the pulse width for PU should be greater than 2.5µs, and there are specific timing relationships between the rising and falling edges of the PU and DR signals, as well as the MF signal, to ensure proper motor control.

4. Operating Instructions

The DM420Y stepper motor driver uses a 6-bit DIP switch to configure its current and subdivision settings.

4.1 Driver Current Setting

The peak output current or RMS value is set using DIP switches SW1, SW2, and SW3. Typically, the current should be set to the motor's rated current. If heat generation is a concern, you can reduce the current, but this will also reduce motor torque. For non-continuous operation, increasing the running current can provide greater torque.

DM420Y Current Settings (Unit: A)
Current RMSCurrent PEAKSW1SW2SW3
DefaultDefaultONONON
0.40.5OFFONON
0.50.7ONOFFON
0.71.0OFFOFFON
0.91.3ONONOFF
1.11.6OFFONOFF
1.41.9ONOFFOFF
1.62.2OFFOFFOFF

Remark: Current RMS is the effective value, Current Peak is the peak value of current.

4.2 Drive Subdivision Settings

Use DIP switches SW4, SW5, and SW6 to set the desired subdivision for the driver.

DM420Y Subdivision Settings
SubdivisionPU/RevSW4SW5SW6
1200ONONON
2400OFFONON
4800ONOFFON
81600OFFOFFON
163200ONONOFF
326400OFFONOFF
6412800ONOFFOFF
12825600OFFOFFOFF

4.3 Lock Current

The DM420Y driver defaults to a half-current lock.

5. Maintenance

The DM420Y Digital Stepper Driver is designed for reliable operation with minimal maintenance. To ensure longevity and optimal performance:

  • Keep Clean: Regularly inspect the driver for dust, oil mist, or conductive particles. Clean gently with a soft, dry cloth. Avoid using solvents or harsh chemicals.
  • Environmental Control: Ensure the operating environment adheres to the specified temperature (0℃ ~ 50℃) and humidity (40 – 90%RH, non-condensing) ranges. Avoid strong vibrations, corrosive gases, and flammable environments.
  • Connection Integrity: Periodically check all wiring connections for tightness and signs of wear or corrosion. Loose connections can lead to intermittent operation or damage.
  • Cooling: Verify that the driver's cooling mechanism (natural convection or forced air with a fan) is unobstructed and functioning effectively to prevent overheating.

No user-serviceable parts are inside the unit. Do not attempt to open or repair the driver yourself, as this will void the warranty and may cause further damage or injury.

6. Troubleshooting

6.1 Driver Status Indicators

The DM420Y driver provides alarm prompts via an indicator light. The state of this light indicates specific alarm information:

DM420Y Alarm Indicator Status
Fault informationALM Pilot lampResetting
Overcurrent or interphase short circuitFlash oncePower-off reset
Overvoltage of supplyFlash twiceAutomatic restoration of standard voltage
The power supply voltage is too low.Flash three timesAutomatic restoration of standard voltage

6.2 General Troubleshooting Methods

Common Issues and Solutions
PhenomenonPossible situationSolution measure
Motor failureThe power light is offCheck the power supply circuit. The power supply is normal.
The motor locks the shaft but does not turnThe IO signal is weak and the signal current is increased.
Too little speedSelection speed.
Whether the release signal MF is connectedDisconnect the MF signal.
Instruction input errorCheck whether the upper computer has a switch output.
Motor direction errorMotor reversalReplace motor wiring sequence or adjust instruction direction.
The motor line has a breakCheck whether the cable is in poor contact.
The motor has only one directionInput port damage.
The motor wire is connected incorrectlyCheck the wiring.
The alarm indicator light is onThe voltage is too high or lowCheck power supply.
The motor or drive is damagedReplace the motor or drive.
Signal interferenceEliminate interference, reliable grounding.
Wrong position or speedInstruction input errorCheck the upper computer instructions to ensure correct output.
Speed setting errorCheck the DIP switch status and connect it correctly.
Motor trippingCheck whether the command speed is too large and the motor selection is small.
The driver terminal is burned outShort-circuit between terminalsCheck the power polarity or external short circuit.
The internal resistance between terminals is too largeCheck whether excess solder is added to the wire and wire connection to form tin pellets.
The acceleration and deceleration time is too shortReduce the command acceleration or increase the driver filter parameter.
Motor stallingMotor torque too smallSelect high torque motor.
Heavy loadCheck the load weight and quality, adjust the mechanical structure.
Too little currentCheck DIP switches to increase the output current of the driver.

7. User Tips

  • Verify DIP Switch Settings: Double-check your current and subdivision DIP switch settings against the tables in this manual before powering on, especially if experiencing unexpected motor behavior.
  • Power Supply Stability: Ensure your power supply provides stable voltage within the 18-36VDC range. Fluctuations can trigger alarm indicators or cause erratic operation.
  • Proper Grounding: For optimal performance and to eliminate signal interference, ensure reliable grounding for your system.
  • Motor Matching: For best results, match the driver's current settings closely to your stepper motor's rated current. Adjusting current can impact heat and torque.

8. Warranty and Support

For detailed warranty information and technical support, please refer to the official STEPPERONLINE website or contact their customer service. A comprehensive user manual in PDF format is also available for download:

View User Manual (PDF)

Contact Information:
Web: www.omc-stepperonline.com
Sales: sales@stepperonline.com
Support: technical@stepperonline.com

9. Product Video Overview

Text Description for Product Video: This video provides a visual overview of the STEPPERONLINE DM420Y Digital Stepper Driver, showcasing its physical appearance, various angles, and terminal connections. It highlights the compact design and the DIP switch settings for current and subdivision.

© 2025 STEPPERONLINE. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.