Lifud LF-GIF030YS

Contents

Lifud LF-GIF030YS Series LED Driver Instruction Manual

Model: LF-GIF030YS (24W-30W, 600mA/700mA/750mA)

For Indoor LED Light Applications

1. Product Overview

The Lifud LF-GIF030YS series is a 30W isolated constant current LED driver designed for indoor LED lighting applications. It features a flicker-free design, high performance, and is suitable for Class II light fixtures. This driver operates with an input voltage range of 220-240Vac and provides a stable output voltage of 33-40Vdc, with selectable output currents of 600mA, 700mA, or 750mA.

Lifud LF-GIF030YS LED Driver Features and Applications
Figure 1: Lifud LF-GIF030YS LED Driver Features and Applications

2. Safety Instructions

  • It is recommended that users install over voltage protection and surge protection devices in the power supply circuits of light fixtures to ensure electrical safety.
  • The LED driver used in combination with the LED device is one of the accessories of the whole light fixture, and the EMC of the whole light fixture is not only susceptible to the driver itself, but to the LED light fixture and the whole light fixture's wiring. Thus, the manufacturer of LED light fixture should re-confirm the EMC of the whole light fixture before the whole light fixture is finished.
  • The test conditions of the circuit breaker configuration quantity are the same as those of the inrush current.
  • The PC cover, casing and end cap for assembling the LED driver in the light fixture must meet the fire rating of UL94-V0 or above.
  • Ensure the input and output connections are correct before powering on.
  • Do not open the driver casing; there are no user-serviceable parts inside.
  • Installation should be performed by a qualified electrician.
Lifud LF-GIF030YS LED Driver Additional Remarks
Figure 2: Safety and Installation Remarks

3. Setup and Installation

3.1 Product Terminals

TerminalDescription
AC-NInput terminal of AC neutral wire
AC-LInput terminal of AC live wire
LED+Positive electrode output of LED driver
LED-Negative electrode output of LED driver

3.2 Structure & Dimensions

The driver has an overall appearance (L*W*H) of 115*41*28 mm. The distance between the two positioning holes is 102.7 mm, and the diameter of the positioning holes is 4.3 mm.

Lifud LF-GIF030YS LED Driver Dimensions and Terminal Definitions
Figure 3: Product Definitions and Dimensions

3.3 Wiring Instructions

  1. Connect the AC neutral wire to the 'AC-N' input terminal.
  2. Connect the AC live wire to the 'AC-L' input terminal.
  3. Connect the positive lead of your LED module to the 'LED+' output terminal.
  4. Connect the negative lead of your LED module to the 'LED-' output terminal.
  5. Ensure all connections are secure and properly insulated.
  6. Verify that the input voltage is within the specified range of 220-240Vac.
  7. Confirm that the LED module's voltage and current requirements match the driver's output specifications (33-40Vdc, 600mA/700mA/750mA).
Lifud LF-GIF030YS0600H LED Driver Label with Wiring Information
Figure 4: LF-GIF030YS0600H Model Label (600mA, 24W)
Lifud LF-GIF030YS0700H LED Driver Label with Wiring Information
Figure 5: LF-GIF030YS0700H Model Label (700mA, 28W)
Lifud LF-GIF030YS0750H LED Driver Label with Wiring Information
Figure 6: LF-GIF030YS0750H Model Label (750mA, 30W)

4. Operating Instructions

Once the Lifud LF-GIF030YS LED Driver is correctly installed and wired, it will automatically provide a constant current output to the connected LED module when power is supplied. The driver is designed for flicker-free operation, ensuring stable and consistent illumination from your LED lights.

  • Ensure the power source is stable and within the specified input voltage range (220-240Vac).
  • The driver will automatically regulate the output current to the specified value (600mA, 700mA, or 750mA depending on the model) to maintain constant brightness and protect the LEDs.
  • No user adjustments are required during normal operation.

5. Maintenance

The Lifud LF-GIF030YS LED Driver is designed for long-term, reliable operation with minimal maintenance. Follow these general guidelines:

  • Keep the driver in a clean, dry environment, free from excessive dust or moisture.
  • Ensure adequate ventilation around the driver to prevent overheating.
  • Periodically check wiring connections for any signs of loosening or damage.
  • Do not attempt to repair the driver yourself. Refer to qualified personnel for any issues.

6. Troubleshooting

If you encounter issues with your LED driver, consider the following:

6.1 Common Issues and Solutions

  • No Light Output:
    • Check if the input power supply is active and within the 220-240Vac range.
    • Verify all wiring connections (AC-N, AC-L, LED+, LED-) are correct and secure.
    • Ensure the LED module is functioning correctly and its specifications match the driver.
  • Flickering or Unstable Light:
    • Confirm stable input voltage.
    • Check for loose connections.
    • Ensure the LED module is compatible with a constant current driver.
  • Overheating:
    • Ensure adequate ventilation around the driver.
    • Verify the ambient temperature is within the specified operating range (-30°C to 45°C).

6.2 Protection Characteristics

The driver incorporates several protection features:

  • Open Circuit Protection: <55V output voltage.
  • Short Circuit Protection: Hiccup mode (auto-recovery).
  • Over Temperature Protection: -30°C to +45°C (ta), -30°C to +90°C (tc).
Lifud LF-GIF030YS LED Driver Electrical Characteristics and Protection
Figure 7: Electrical and Protection Characteristics

7. Specifications

7.1 General Specifications

  • Model Number: LF-GIF030YS
  • Output Type: SINGLE
  • Origin: Mainland China
  • IP Level: IP20
  • High-concerned chemical: None

7.2 Electrical Characteristics

ParameterValue
Input Voltage220-240Vac (max input voltage: 198-264Vac)
Input Frequency50/60Hz
Input Current0.2A max.
Output Voltage33-40Vdc
Output Current600mA, 700mA, 750mA (selectable models)
Output Power24-30W (1-50W range)
PF≥0.9
THD≤20%
Efficiency≥86% (600mA), ≥86.5% (700mA), ≥87% (750mA)
Inrush Current≤24A & 144uS
Startup Time<0.5S
Flicker Index (Modulation Depth)Complies with IEEE 1789-2015 standard
CIE SVM≤0.4
IEC-Pst≤1
Current Tolerance±5%
Temperature Drift±10%

7.3 Environmental Conditions

  • Operating Temperature: -30°C to +45°C
  • Operating Humidity: 20-90%RH (no condensation)
  • Storage Temperature/Humidity: -30°C to +80°C (6 months in Class I environment); 10-90%RH (no condensation)
  • Atmospheric Pressure: 86-106kPa

7.4 Certifications & Safety Standards

  • Certificates: TUV CB CE RCM, ENEC, UKCA, SAA, CCC
  • Withstanding Voltage: I/P-O/P: 3.75kV & 5mA & 60S
  • Insulation Resistance: I/P-O/P: >100MΩ @ 500Vdc
  • Safety Standards: ENEC: EN61347-1: 2015, EN61347-2-13: 2014/A1: 2017, EN62384 2016/A1: 2009, CE-LVD: EN61347-2-13: 2014/A1: 2017, EN61347-1: 2015, EN62493: 2015, CB: IEC61347-1: 2015, IEC61347-2-3: 2014, IEC 61347-2-13: 2014/AMD1: 2017, UKCA-LVD: EN61347-1: 2015/A1: 2021, EN61347-2-13: 2014/A1: 2017, EN62493: 2015, CCC: GB19510.1-2009, GB19510.14-2009, RCM: AS/NZS 61347.1, AS/NZS 61347.2.13, SAA: AS 61347.2-13: 2018
  • EMI: CE-EMC/RCM: EN55015, EN61000-3-2, EN61000-3-3, UKCA-EMC: EN IEC 55015, 2019/A11: 2020, EN 61547: 2009, EN IEC 61000-3-2: 2019/A1: 2021, EN 61000-3-3: 2013/A2: 2021, CCC: GB/T17743, GB17625.1, GB17625.2
  • EMS: CE-EMC/RCM: EN61000-4-2, 3, 4, 5 (lightning strike 1kV), 6, 11
  • RoHS: RoHS 2.0 (EU) 2015/863
Lifud LF-GIF030YS LED Driver Certifications and Safety Standards
Figure 8: Certifications and Safety Information

7.5 Packaging Specifications

ParameterValue
ModelLF-GIF030YSxxxxH
Carton Size (L*W*H)385*285*210mm
Quantity18 pcs/layer; 6 layers/ctn; 108 pcs/ctn
Weight0.096 kg/pc; 10.6 kg/ctn

8. User Tips

  • Always ensure the total wattage of your LED modules does not exceed the driver's maximum output power (30W for this series).
  • For optimal performance and longevity, operate the driver within its specified temperature and humidity ranges.
  • Consider using appropriate surge protection for the AC input, especially in areas prone to power fluctuations.

9. Warranty and Support

The Lifud LF-GIF030YS LED Driver comes with a 5-year warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use and service conditions. Please refer to the full warranty conditions for details.

9.1 Contact Information

For technical support, warranty claims, or general inquiries, please contact Lifud Technology Co., Ltd. using the information below:

  • Address: Production Base 1 (B-2), Building 8, Kutto Industrial Park, NO.26 Xinhu Road, Bao'an District, Shenzhen, China.
  • Telephone: +86(0)755 8373 9299
  • Website: www.lifud.com
  • Email: sales@lifud.com

© 2023 Lifud Technology Co., Ltd. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.