1. Introduction
The Kiprim Combustible Gas Leak Detector is a high-performance device designed to detect the presence of various combustible gases, including natural gas, methane (CH4), propane (C3H8), butane (C4H10), LPG, gasoline, ethanol, and alcohol. It features a flexible probe, visual and audible alarms, and a clear digital display for accurate readings in PPM and %LEL. This detector is an essential tool for ensuring safety by identifying potential gas leaks in residential, commercial, and outdoor settings.

Figure 1: Varieties of Combustible Gases Detected
2. Safety Information
- Always operate the device in a well-ventilated area.
- Do not expose the device to extreme temperatures or humidity.
- Keep the device away from strong electromagnetic fields.
- Ensure the battery compartment is securely closed during operation.
- Do not attempt to repair or modify the device yourself. Refer to qualified personnel for service.
- In case of a detected gas leak, immediately ventilate the area, turn off gas sources if safe to do so, and evacuate. Contact emergency services if necessary.

Figure 2: Dangers of Gas Leaks
3. Product Overview
The Kiprim Combustible Gas Leak Detector is equipped with a flexible probe for reaching difficult areas and a clear LCD screen for displaying readings and status indicators.

Figure 3: Device Components and Controls
- Flashlight
- High performance sensor
- Flexible hose
- Display screen
- Power switch
- Two measuring units (%LEL & PPM)
- High or low sensitivity switchover / Cancel auto power-off
- Flashlight on / zero clearing
- Sound off, Celsius/Fahrenheit switchover
- Auto off
- Battery low voltage indicator
- High sensitivity indicator
- Low sensitivity indicator
- Screen analog display
- Sound off indicator
- Sound on indicator
- Zero clearing indicator
- Measurement unit indicator
- Detected value display
- Ambient temperature display
- Humidity display
4. Setup
4.1 Battery Installation
- Locate the battery compartment on the back of the device.
- Use a screwdriver to open the battery cover.
- Insert three (3) AAA batteries, ensuring correct polarity.
- Close the battery cover and secure it with the screw.
Video: Kiprim Combustible Gas Detector GD01/GD02 Basic Operations (0:19 - 0:22 shows battery installation)
5. Operating Instructions
5.1 Power On and Warm-up
- Press the power button (5) to turn on the device.
- The device will enter a warm-up phase, which takes approximately 30 seconds. Wait until the preheating is complete before starting any tests.
Video: Kiprim Combustible Gas Detector GD01/GD02 Basic Operations (0:23 - 0:28 shows power on and warm-up)
5.2 Sensitivity Adjustment
The device offers high and low sensitivity modes. Switch between them using the H/L button (7).
Video: Kiprim Combustible Gas Detector GD01/GD02 Basic Operations (0:29 - 0:33 shows sensitivity switching)
5.3 Using the LED Light
To illuminate dark areas during inspection, short press the APO button (8) to turn the LED light (1) on or off.
Video: Kiprim Combustible Gas Leak Detector GD01/GD02 Basic Operations (0:34 - 0:39 shows LED light operation)

Figure 4: Flashlight in Use
5.4 Automatic Shutdown Settings
To enable or disable the automatic power-off function, long press the APO button (10).
Video: Kiprim Combustible Gas Leak Detector GD01/GD02 Basic Operations (0:40 - 0:44 shows automatic shutdown settings)
5.5 Zero Function
Press the ZERO button (17) to return the reading to zero. This is important for accurate measurements in a clean air environment.
Video: Kiprim Combustible Gas Leak Detector GD01/GD02 Basic Operations (0:45 - 0:50 shows zero function)
5.6 Sound On/Off
Short press the °C/°F button (9) to toggle the sound on or off.
Video: Kiprim Combustible Gas Leak Detector GD01/GD02 Basic Operations (0:51 - 0:55 shows sound on/off)
5.7 Temperature Unit Switching
Long press the °C/°F button (9) to switch the temperature unit between Celsius (°C) and Fahrenheit (°F).
Video: Kiprim Combustible Gas Leak Detector GD01/GD02 Basic Operations (0:56 - 1:00 shows temperature unit switching)
5.8 Pre-Test Check
Before each use, it is recommended to perform a quick check. Lightly press the handle of an igniter near the sensor to confirm gas detection. This ensures the sensor is functioning correctly.
Video: Kiprim Combustible Gas Leak Detector GD01/GD02 Basic Operations (1:01 - 1:06 shows pre-test check)
5.9 Testing for Leaks
- Ensure the device has completed its warm-up and is zeroed in a clean air environment.
- Slowly approach the sensing part (2) of the flexible probe (3) to the suspected area of gas leakage.
- Observe the digital display (19) for PPM or %LEL readings and the analog display (14) for visual indication.
- The device will provide audible and visual alarms (15, 16) if a gas leak is detected.
Video: Kiprim Combustible Gas Leak Detector GD01/GD02 Basic Operations (1:07 - 1:16 shows gas leak testing)

Figure 5: Flexible Probe in Action
5.10 Interpreting Readings
The device displays gas concentration in both PPM (Parts Per Million) and %LEL (Lower Explosive Limit). You can use %LEL to understand the explosive potential of a gas concentration, while PPM provides a more exact measurement.

Figure 6: Digital Display Readings
The analog display (14) and audible alarms indicate gas concentration levels:
- Faint: Low concentration, green bar.
- Attention: Moderate concentration, yellow bar.
- Warning: Higher concentration, orange bar.
- Danger: High concentration, red bar, rapid alarm.

Figure 7: Four-Digit Reading for Accuracy

Figure 8: Potential Sources of Gas Leaks
6. Maintenance
- Keep the device clean and free from dust and debris. Use a soft, dry cloth for cleaning.
- Store the device in a cool, dry place when not in use.
- Replace batteries promptly when the low battery indicator (11) appears to ensure accurate readings.
- Avoid dropping the device or subjecting it to strong impacts.
7. Troubleshooting
- Device does not power on: Check battery installation and ensure batteries are fresh.
- Inaccurate readings: Ensure the device has completed its warm-up phase and has been zeroed in a clean air environment. Avoid testing in areas with strong air currents.
- No alarm when gas is present: Check if the sound is muted (refer to section 5.6). Ensure the sensor is clean and unobstructed.
- Low battery indicator: Replace all three AAA batteries.
8. Specifications
| Feature | Specification |
|---|---|
| Brand Name | Kiprim |
| Model Number | GD01/GD02 |
| Gas Type | Multifunctional (Combustible Gases) |
| Detection Range | 50-10000ppm |
| Response Time | <2 seconds |
| Probe Length | 15.7 inches (Flexible Gooseneck) |
| Display | LCD Screen with Analog Display |
| Alarms | Audible and Visual |
| Temperature & Humidity Measurement | Yes (High-precision sensors) |
| Power Source | 3x AAA Batteries (Not included) |
| Auto Power-off | Cancellable |
| Flashlight | Yes |
| Is Smart Device | No |
| DIY Supplies | Electrical |
9. User Tips
- Always ensure you have fresh AAA batteries on hand, as they are not included with the device.
- Perform the pre-test check with an igniter before each use to confirm the sensor's functionality.
- Utilize the flexible 15.7-inch gooseneck probe to reach confined spaces and potential leak points that are difficult to access directly.
- Remember to zero the device in a clean air environment before starting your leak detection to ensure the most accurate baseline reading.
10. Warranty and Support
For warranty information or technical support, please refer to the contact details provided by your retailer or visit the official Kiprim website. Keep your purchase receipt as proof of purchase.