NISSEI RX-103

Contents

NISSEI RX-103 Mini SWR/Watt Meter User Manual

Model: RX-103

Brand: NISSEI

1. Introduction

The NISSEI RX-103 Mini SWR/Watt Meter is a high-quality instrument designed for measuring forward power, reflected power, and Standing Wave Ratio (SWR) across the 1.6-60MHz frequency range. It supports both average and peak envelope power (PEP) measurements for SSB and AM transmitters, with a maximum measurable power of up to 2KW. Its low insertion loss allows for permanent installation in your antenna system, making it an essential tool for amateur radio enthusiasts and walkie-talkie users to ensure optimal performance and safety of their equipment.

2. Package Contents

Please check the package for the following items:

  • 1 x NISSEI RX-103 SWR/Watt Meter
  • 1 x 13.8V DC Power Cable
  • 1 x User Manual (this document)

3. Setup and Connections

Before operating the device, ensure all connections are secure and correct.

  1. Identify Ports: Locate the 'TX' (Transmitter), 'ANT' (Antenna), and 'DC 13.8V' power input ports on the rear panel of the meter. All RF connectors are M-J type.
  2. Connect Antenna: Connect your antenna cable to the 'ANT' port on the rear of the RX-103.
  3. Connect Transmitter/Radio: Connect your radio or transmitter's output to the 'TX' port on the rear of the RX-103.
  4. Connect Power: Connect the provided 13.8V DC power cable to the 'DC 13.8V' input on the rear panel. Ensure the power supply is capable of providing stable 13.8V DC.
Rear view of NISSEI RX-103 SWR/Watt Meter showing TX, ANT, and DC 13.8V ports
Figure 1: Rear panel connections (TX, ANT, DC 13.8V)
Front view of NISSEI RX-103 SWR/Watt Meter showing meter display, range switch, and AVG/PEP switch
Figure 2: Front panel controls and display

4. Operating Instructions

The RX-103 allows for precise measurement of RF power and SWR.

4.1 Power On

Once all connections are made, apply 13.8V DC power. The meter's backlight (if equipped) should illuminate, and the needle will rest at zero.

4.2 Range Selection

Use the 'RANGE' knob on the front panel to select the appropriate power range for your measurement:

  • X1: For low power measurements (e.g., 0-20W).
  • X10: For medium power measurements (e.g., 0-200W).
  • X100: For high power measurements (e.g., 0-2000W).

Always start with a higher range (e.g., X100) and decrease if the reading is too low, to prevent damage to the meter.

4.3 Measurement Mode (AVG / PEP)

The 'AVG / PEP' switch allows you to select between average power and peak envelope power measurements:

  • AVG (Average): Used for continuous wave (CW), FM, and RTTY modes.
  • PEP (Peak Envelope Power): Used for single-sideband (SSB) and amplitude modulation (AM) modes, where power fluctuates.

4.4 Reading the Meter

The meter display shows three scales:

  • FORWARD (FWD): Indicates the power transmitted from your radio.
  • REFLECTED (REF): Indicates the power reflected back from the antenna system.
  • SWR: Indicates the Standing Wave Ratio, a measure of how well your antenna is matched to your radio.

4.5 SWR Measurement Procedure

  1. Set the 'RANGE' knob to an appropriate setting (start high).
  2. Set the 'AVG / PEP' switch to 'AVG' for initial tuning, or 'PEP' for SSB/AM.
  3. Transmit a steady carrier (e.g., using CW or FM mode) at a low power level initially.
  4. Observe the FWD and REF needles. The SWR is read directly from the SWR scale where the needles intersect.
  5. Adjust your antenna tuner or antenna system as needed to minimize the reflected power and achieve the lowest possible SWR (ideally 1.0:1 to 1.5:1).

4.6 Power Measurement Procedure

  1. Set the 'RANGE' knob to an appropriate setting based on your expected power output.
  2. Set the 'AVG / PEP' switch to 'AVG' for average power or 'PEP' for peak power.
  3. Transmit normally.
  4. Read the power directly from the 'FORWARD (W)' scale, corresponding to the selected range.

5. Maintenance

To ensure the longevity and accuracy of your NISSEI RX-103, follow these maintenance guidelines:

  • Cleaning: Use a soft, dry cloth to clean the exterior of the meter. Do not use abrasive cleaners or solvents.
  • Storage: Store the meter in a cool, dry place away from direct sunlight and extreme temperatures.
  • Connections: Periodically check all cable connections for tightness and corrosion.
  • Avoid Impact: Handle the meter with care to avoid physical shock, which can affect the delicate internal components and meter movement.

6. Troubleshooting

If you encounter issues with your RX-103, refer to the following common problems and solutions:

ProblemPossible CauseSolution
Meter does not power on / No backlightNo 13.8V DC power; Faulty power cable; Incorrect polarity.Check DC power supply connection and voltage. Ensure correct polarity. Test with another 13.8V DC source if available.
No FWD/REF readingIncorrect cable connections; No RF output from radio; Faulty cables.Verify TX and ANT connections. Ensure radio is transmitting. Check RF cables for damage.
SWR reading is very highAntenna mismatch; Faulty antenna; Open/short circuit in antenna system.Check antenna tuning. Inspect antenna and feedline for damage. Ensure proper grounding.
Inaccurate power readingsIncorrect RANGE setting; Meter calibration issue.Ensure the RANGE knob is set appropriately for the power level. If issues persist, contact support.

7. Specifications

FeatureSpecification
Model NumberRX-103
Item TypeMeter
Frequency Range1.6 - 60MHz
Measurable Power RangeUp to 2KW
Minimum Measuring Power1W
Impedance50ohm
Connector TypeM-J connector
Product Size (L x W x H)140 x 84 x 122mm
Product WeightApprox. 0.9kg
Precision (5W Input) - Average±10%
Precision (5W Input) - Peak±15%
Precision (20-2000W Input) - Average±5%
Precision (20-2000W Input) - Peak±10%

8. User Tips

  • Broad Compatibility: The RX-103 is suitable for a wide range of radio communication devices, including amateur radio transceivers and CB radios (often referred to as 'radio px'). Its broad frequency range of 1.6-60MHz covers many popular bands.
  • Permanent Installation: Due to its low insertion loss (0.3 dB or lower), the RX-103 can be left permanently connected in your antenna line without significantly degrading signal quality. This allows for continuous monitoring of your antenna system's performance.
  • Initial Setup: When first setting up, always start with the highest power range (X100) to avoid overloading the meter, then adjust downwards as needed for more precise readings.

9. Warranty and Support

For any questions, technical assistance, or warranty claims, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.