BAOFENG UV-32

Contents

Baofeng UV-32 Walkie Talkie User Manual

Model: UV-32 | Brand: BAOFENG

1. Introduction and Safety Warnings

Thank you for purchasing the UV-32 Series Amateur Radio, a Dual band/Dual display/Dual watch device. This easy-to-use radio provides secure, instant, and reliable communications. Please read this manual carefully before use to ensure maximum performance and safe operation.

1.1 Regulations and Safety Warnings

WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.

EU Regulatory Conformance: This product complies with Directive 2014/53/EU and other relevant provisions. Operation is permitted under 2000m. European users must hold a valid Amateur Radio License for the frequencies and power levels used for transmission. This information applies to EU countries only.

Compliance with RF Exposure Standards: The radio complies with United States Federal Communications Commission (47 CFR § 1.1307, 1.1310, 2.1093) and American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005 guidelines.

Guidelines and Operating Instructions for RF Exposure:

  • Do not remove the RF Exposure Label.
  • User awareness instructions should accompany the device if transferred.
  • Do not use if operational requirements are not met.
  • Transmit no more than 50% of the time. Press the Push-to-Talk (PTT) key to transmit, release to receive.
  • Keep the radio unit at least 2.5cm away from the face during transmission.
  • When worn on the body, always use an approved holder, holster, case, or body harness.
  • Use of non-approved antennas, batteries, and accessories may exceed FCC RF exposure guidelines.

1.2 Important Tips for Portable Terminals

  • Do not operate in locations with fuels, chemicals, or explosive atmospheres.
  • Do not operate near blasting areas or medical/electronic equipment vulnerable to RF signals.
  • Do not hold the product while driving.
  • Do not disassemble, modify, or repair the product without authorization.
  • Keep the product and accessories out of reach of children and pets.
  • Operate within the specified temperature range.
  • Continuous transmission may lead to heat accumulation; allow for cooling.

1.3 Precautions for Batteries

  • Do not charge or replace batteries in locations with fuels, chemicals, or explosive atmospheres.
  • Do not charge wet batteries; dry them first.
  • Do not charge deformed, leaking, or overheated batteries.
  • Do not use unauthorized chargers.
  • Do not charge in areas with strong radiation.
  • Avoid overcharging to prolong battery life.
  • Do not short-circuit battery terminals or throw batteries into fire.
  • Do not remove the casing from the battery pack.

2. Package Contents

Your Baofeng UV-32 Walkie Talkie package includes the following items:

  • 1x Portable Radio (UV-32)
  • 1x Antenna
  • 1x Li-ion Battery Pack
  • 1x Desktop Charger
  • 1x Type-C Cable (for direct charging)
  • 1x Back Clip
  • 1x Sling
  • 1x User's Manual (this document)

Note: Additional accessories may be included depending on your specific purchase option.

3. Product Overview

Familiarize yourself with the components of your UV-32 radio:

Baofeng UV-32 Walkie Talkie labeled diagram showing antenna, encoder, PTT key, side keys, LCD screen, speaker, numeric keypad, microphone, charge contact, and Type-C charging port.
Figure 3.1: Baofeng UV-32 Radio Components
  1. Antenna
  2. Encoder/Channel Selector Switch
  3. TX_RX Status Indication (LED)
  4. Power/Volume Knob
  5. 2.0" Color LCD Screen
  6. PTT Key (Push-to-Talk)
  7. Side Key (SK1) - Short press for custom function, long press for emergency alarm
  8. Side Key (SK2) - Sweep/Monitor
  9. Numeric Keypad
  10. Built-in Microphone
  11. Charge Contact
  12. Speaker
  13. Accessory Port
  14. Type-C Charging Port

3.1 LCD Icon Summary

The LCD screen displays various icons to indicate the radio's status and functions:

Icon Description
🔋Battery level indicator
♫DTMF side tone enabled
DDual watch enabled
VVOX enabled
*Bluetooth frequency writing function activated
📍GNSS function enabled (GPS)
🔒Keypad lock enabled
ZONE01Current channel's region (storage mode)
VFOCurrent working VFO mode (manual frequency input)
AUpper section display and emission level indication
BLower section display and emission level indication
HTransmit power level: High
MTransmit power level: Medium
LTransmit power level: Low
DDCS enabled
CCTCSS enabled
+Repeaters access enabled (TX shifted higher than RX)
-Repeaters access enabled (TX shifted lower than RX)
RReverse function enabled
TTalkaround activated
✔Confidential calling feature activated
NNarrowband enabled

4. Setup

4.1 Installing / Removing the Battery

Installing the Battery Pack:

  1. Position the battery pack over the back of the radio.
  2. Engage the battery pack into the radio until it is fully seated.
  3. Tighten the screws using a coin or object to secure the battery pack. Do not overtighten.

Removing the Battery Pack:

  1. Loosen the screws on the back of the battery pack.
  2. Lift the bottom of the battery pack slightly to remove it from the radio housing.
  3. Pull the battery pack out of the radio housing.

4.2 Installing / Removing the Antenna

Installing the Antenna:

Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure.

Removing the Antenna:

Turn the antenna counter-clockwise to remove it.

4.3 Installing Additional Speaker/Microphone (Optional)

Pry open the rubber MIC-Headset jack cover and then insert the Speaker / Microphone plug into the double jack.

5. Charging the Battery

The Li-ion battery pack is not charged from the factory; please charge it before first use. Full charging/discharging cycles two or three times will optimize battery performance.

Always use the specified charger provided by Baofeng. Other models may cause damage or injury.

5.1 Charging Methods

The UV-32 supports two convenient charging methods:

Image showing the Baofeng UV-32 radio being charged via a Type-C USB cable connected to a power bank.
Figure 5.1: Type-C Fast Charging

Type-C Direct Charging:

  1. Ensure your radio is turned OFF.
  2. Plug the Type-C cable into the Type-C charging port on your battery.
  3. Connect the other end of the Type-C charger to a wall power outlet, power bank, or laptop.
  4. An empty battery will be fully charged in approximately 6 hours.
Image showing the Baofeng UV-32 radio placed in its charging cradle, connected to a wall adapter.
Figure 5.2: Base Charging

Base Charging:

  1. Ensure your radio is turned OFF.
  2. Place the radio with the battery pack into the charging cradle.
  3. Connect the charging cradle to a power source using the provided power adapter.

5.2 LED Indicator for Charging Status

Red LED Green LED Status
FlashingSteadyStandby (charger empty) / Error (charger with radio)
SteadyOffCharging
OffSteadyCharge complete

Note: The radio should be turned OFF during the charge cycle for optimal charging.

6. Basic Operations

6.1 Power On/Off and Volume Adjustment

Power On:

Rotate the Volume/Power knob clockwise until you hear a "click". The radio will display a message or flash the LCD, then show a frequency or channel. If voice prompt is enabled, it will announce "frequency mode" or "channel mode".

Power Off:

Rotate the Volume/Power knob counter-clockwise all the way until you hear a "click".

Adjusting Volume:

Rotate the Volume/Power knob clockwise to increase volume, counter-clockwise to decrease. Be careful not to turn it too far and accidentally power off the radio.

6.2 Main Band/Sub Band Switch

In standby mode, press the ↑ key to switch between the main frequency band and sub-frequency bands. The band with the larger display font is the primary band.

6.3 VFO/Channel Switch

Press and hold the ↑ key to switch between VFO (Frequency) mode and Channel (MR) mode.

  • In Channel (MR) mode, the channel number is displayed.
  • In Frequency (VFO) mode, "VFO" is displayed.

6.4 Frequency (VFO) Mode

In VFO mode, you can navigate up and down the band using the ↑ or ↓ keys, or input frequencies directly using the numeric keypad with kilohertz accuracy.

WARNING: Transmitting on unauthorized frequencies is illegal and a serious offense. Always ensure you have proper authorization for the frequencies you use.

6.5 Channel (MR) Mode and Channel Selection

Channel (MR) mode is practical for everyday use with preprogrammed channels. To select a channel:

  • Use the ↑ or ↓ navigation keys or the encoder.
  • Input channel numbers directly using the keypad (e.g., [0][1][2] for channel 12).

6.6 Select a Bank

The radio supports up to 10 banks, each with a maximum of 100 channels. To select a bank, go to Menu > Bank, then use navigation keys to select and confirm.

6.7 Making a Call

Use the A/B key to switch between main and other channels if two are displayed. In standby, press [V/M] to switch between VFO and MR mode.

Channel Mode Call:

Select a channel, then hold down the [PTT] key to transmit. Speak into the microphone with a normal tone. The red LED will be on during transmission.

Frequency Mode Call:

Switch to VFO mode, input the working frequency, then hold down the [PTT] key to transmit.

Receiving a Call:

Release the [PTT] key. The green LED will be on when receiving a call.

Note: Keep the microphone 2.5 cm to 5 cm from your mouth for best reception volume during transmission.

6.8 Emergency Alert

To activate, press and hold the [SK1] key for 3 seconds. The radio will emit a loud siren and the flashlight will flash. Press [SK1] again to exit. WARNING: Only use in actual emergencies.

6.9 FM Radio (FM)

Listen to FM radio on frequencies 65-108MHz. Press the ↑ key to switch between 65-75 MHz and 76-108 MHz bands.

  1. In frequency or channel mode, press [SK1] key to turn on the radio.
  2. Select desired frequency with ↑ or ↓ keys or input directly. Or press # to auto-search.
  3. Press [SK1] key to exit FM radio.

6.10 Monitor

In standby, press and hold the [SK2] key to enter Monitor mode to listen to weak signals. Release [SK2] to exit.

6.11 Keypad Lock

Press and hold the * key for about two seconds to enable/disable the keypad lock. The radio can also be set to automatically lock after ten seconds of inactivity via the menu.

6.12 Frequency Reversal and Talkaround

A short momentary press of the * key enables the reverse function, swapping transmit and receive frequencies. Pressing it again switches to talkaround mode, where transmit and receive frequencies are equal.

6.13 TX Repeaters Tone

Press [PTT] + [SK1] key to send a 1750Hz repeaters tone, useful for communications through repeaters.

Define [SK1] as a Search function via CPS software or Radio Menu > Radio Setting. Briefly press the preset 'Search' key to start scanning. The radio will display "SEARCH SEEK..." and show the received frequency if a stable signal is found.

7. Advanced Features

7.1 Scanner

The UV-32 features a built-in scanner for VHF and UHF bands. In VFO mode, it scans in steps; in MR mode, it scans channels. To enable, press and hold the # key for about two seconds. Use ↑ or ↓ keys to change scanning direction. Press and hold # again to exit.

Frequency Ranger:

In frequency mode, precisely set the sweep range (e.g., 144.000-146.000MHz). See Menu > SCAN > Freq Ranger.

Scan Modes:

  • Time Operation (TO): Scanner stops on a signal, resumes after a preset time.
  • Carrier Operation (CO): Scanner stops on a signal, resumes after a preset time with no signal.
  • Search Operation (SE): Scanner stops on a signal. Press # again to resume.

Scan Sub-Code (CTCSS/DCS):

To search for a CTCSS code: In VFO mode, enter a known frequency (e.g., 144.525). Press ↑ to Menu > Scan > 3 Scan Sub-Code. Select CTCSS, then press ↑ to scan. Save with ↑. Similar steps for DCS codes.

7.2 Dual Watch

The radio can monitor two channels simultaneously. To enable/disable Dual Watch: Press ↑ to enter the main menu. Enter [4] for Radio Settings, confirm, then enter [16] for 15 Dual Watch. Press ↑ to select ON/OFF.

7.3 Manual Programming (Channels Memory)

Memory channels store frequently used frequencies. The radio has 10 zones, each with up to 100 channels. Each channel can store RX/TX frequencies, power, signaling, bandwidth, and a 6-character alphanumeric identifier.

Programming a Channel Repeater Offset with CTCSS Tone (Example for Channel 10):

  1. Press ↑ to switch menus.
  2. Press and hold ↑ to set to VFO mode.
  3. Use menu options to delete prior data in Channel 10, select RX/TX encode tones (e.g., 123.0 CTCSS), enter OFFSET frequency (e.g., 5.00MHz), and select offset direction (+).
  4. Enter RX frequency (e.g., 432.55000 MHz).
  5. Enter the same channel (10).
  6. Press V/M key to return to MR mode.

7.4 Repeaters Programming

These instructions assume knowledge of repeater frequencies and authorization to use them.

  1. Press and hold ↑ to set to VFO mode.
  2. Use numeric keypad to enter repeater's output (receive) frequency.
  3. Press ↑ [6] [1][0] to get offset frequency.
  4. Use numeric keypad to enter specified frequency offset.
  5. Press ↑ to confirm and save.
  6. Press ↑ [6] [1][1] to get offset direction.
  7. Use ↑ or ↓ keys to select plus (+) or minus (-) offset.
  8. Press ↑ to confirm and save.
  9. Optional: Save to memory (see Manual Programming) or set up CTCSS.
  10. Press ↑ to exit menu.

Note: If experiencing connection problems, check settings or consult your local amateur radio club.

7.5 GPS Function

The UV-32 features GPS positioning for accurate location tracking and sharing.

Baofeng UV-32 radios displaying GPS positioning information on their screens, with a network of connected points in the background.
Figure 7.1: GPS Positioning Feature

Use of GPS:

In standby mode, press [P1] key to enter GPS mode and display "My Place". Press [P2] to enter GPS mode and display the coordinate interface. The radio supports multi-mode GPS (BDS, GPS, or GPS+BDS).

Find My Place:

  1. Press [P1] key to enter GPS mode.
  2. Use the ↑ or ↓ key to switch to "My Place".
  3. GPS will display "Searching...". A red GPS character indicates positioning is not successful.
  4. Once "Searching Successful" is displayed, the GPS character turns green, showing current time, longitude, latitude, and altitude.
  5. Press the ↑ key to switch between GPS position information and GPS distance/direction interfaces.

Share My Place Information (Send to Others):

  1. After successful GPS positioning, press the ↑ key to switch to the location information interface.
  2. Press the ↑ or ↓ key to select the pre-programmed member sequence (01-20) labeled as "native".
  3. Press the [PTT] key to share current location information with group members.

Requesting Someone Else's Place:

  1. After successful GPS positioning, press the ↑ key to switch to the My Place information interface.
  2. Press the ↑ or ↓ key to select a pre-programmed member sequence (01-20) not marked as "native".
  3. Press the [PTT] key to initiate a position request command to the target member.

7.6 Bluetooth Write Frequency

The UV-32 supports Bluetooth programming via a dedicated app, simplifying frequency customization.

QR codes for downloading the Bluetooth Programming APP for iOS and Android devices.
Figure 7.2: Bluetooth Programming APP QR Codes

Procedure:

  1. Download and install the BAOFENG radio APP on your Android or iOS phone by scanning the QR codes above.
  2. On the radio, press ↑ + [3] to enter Bluetooth frequency writing.
  3. Press ↑ + ↑ or ↓ to select "On". The Bluetooth icon * will appear on the screen.
  4. Open the BAOFENG radio APP, allow Bluetooth and positioning.
  5. Select "Baofeng" brand, then "UV32 Pro Series" model.
  6. Connect to the radio via the app. Once connected, you can read and write frequencies.

Read Frequency:

After reading, click 'program' in the app to view and edit channel information, frequency mode, and optional functions.

Save Profile:

Save programmed schemes as new profiles. You can also replace existing profiles.

Write Frequency:

In the app, tap 'Home', select 'Program', then 'Write Frequency'. The radio will restart automatically after writing is complete.

8. Maintenance

8.1 Battery Maintenance

  • Only charge batteries in normal room temperatures (5°C-40°C / 40°F-105°F).
  • Turn off the radio when charging an attached battery for faster charging.
  • Do not unplug the charger or remove the battery/radio until charging is complete (green light is on).
  • Never charge a wet battery.
  • If operating time significantly shortens, consider purchasing a new battery.
  • Battery performance reduces in freezing temperatures; keep a spare battery warm.
  • Clean charging contacts regularly with a clean, dry cloth.

8.2 How to Store the Battery

  • Store the battery at approximately 80% discharge.
  • Keep in a low temperature and dry environment.
  • Avoid hot places and direct sunlight.
  • For long-term storage, cycle the battery at least every six months to prevent severe capacity degradation.

9. Troubleshooting Guide

Phenomena Analysis Solution
Cannot turn on the radio. Battery installed improperly. Remove and reattach the battery.
Battery power may run out. Recharge or replace the battery.
Poor contact due to dirty/damaged battery contacts. Clean battery contacts or replace the battery.
Weak or intermittent voice during reception. Battery voltage low. Recharge or replace the battery.
Volume level low. Increase the volume.
Antenna loose or improperly installed. Turn off radio, remove and reattach antenna.
Speaker blocked. Clean the surface of the speaker. Clean the surface of the speaker.
Cannot communicate with other group members. Frequency or signaling type inconsistent. Verify TX/RX frequency and signaling type are correct.
Too far away from other members. Move towards other members.
Interrupted by radios using same frequency. Change the frequency, or adjust the squelch level. Change the frequency, or adjust the squelch level.
Unknown voices or noise. Radio in analog mode with no signaling. Request dealer to set signaling for current channel.
Unable to hear anyone due to noise/hiss. Too far away from other members. Move towards other members.
Unfavorable position (blocked by buildings/underground). Move to an open, flat area, restart radio, try again.
External disturbance (electromagnetic interference). Stay away from equipment causing interference.
Radio keeps transmitting. VOX turned on or headset not installed. Turn off VOX function. Check headset installation.

Note: If these solutions do not resolve your issues, please contact your dealer for technical support.

10. Technical Specifications

General
Channel Capacity1000 / 10 Bank
Channel Spacing25.0 KHz / 12.5 KHz
Input Voltage7.4 VDC
Battery Life (5% TX, 5% RX, 90% Standby)Li-on: 18 hours @ 5 watts
Operating Temperature-10°C to 60°C
Antenna Impedance50Ω
Radio Dimensions182 × 67 × 41 mm (not including antenna)
Radio Weight350 g (with Li-ON battery)
Transmitter
Frequency Range (TX)144 to 148 MHz, 420 to 450 MHz (America version)
144 to 148 MHz, 430 to 450 MHz (Canadian version)
144 to 146 MHz, 430 to 440 MHz (European Union version)*
Modulation16K0F3E / 11K0F3E
Spurious Emission-16 dBm < 1GHz, -16 dBm > 1GHz
Frequency Stability±2.5 ppm
Audio Distortion≤5%
FM Hum & Noise40 dB
Receiver
Frequency RangeFM 76-108MHz; AM 108-136MHz; VHF: 136-174 MHz; 220-260MHz; UHF: 350-390MHz; 400-520 MHz;
Sensitivity (12 dB SINAD)-120 dBm
Adjacent Channel Selectivity-60 dBm
Intermodulation and Rejection-70 dBm
Rated Audio Power Output0.75 Watts @ 16 Ω
Rated Audio Distortion≤5%

Note: All specifications may be modified without prior notice or liability.

11. User Tips

  • Initial Testing: After initial setup, perform thorough testing to confirm the radio's performance across different bands and features.
  • GPS and APRS: The UV-32 features GPS positioning. If you intend to use it with APRS (Automatic Packet Reporting System) maps, verify its compatibility and configuration for such applications.
  • Damaged Shipments: If your product arrives damaged, contact the seller immediately for assistance.

12. Warranty and Support

12.1 EU Declaration of Conformity

Baofeng and Pofung declare that the radio equipment type listed in Technical Specifications complies with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at: http://www.pofung.cn/download.asp?EnBigClassName=EU%20DOC.

You can also consult your local Baofeng helpdesk, your dealer, or send an email to wangjianhui@baofengradio.com.

12.2 Additional Resources

For a detailed PDF version of this user manual, please refer to the official document: User Manual (PDF).

For more information, visit the official website: http://www.baofengradio.com.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.