MEISHIDA 9917B

Contents

MEISHIDA 9917B Fully Automatic Smart Toilet User Manual

Model: 9917B

1. Safety Information

Please read all safety instructions carefully before installation and use. Failure to follow these instructions may result in electric shock, fire, injury, or property damage.

⚠ WARNING (Potential for Serious Injury or Death)

  • Do NOT disassemble, modify, or repair the unit yourself. This can lead to fire, electric shock, or injury.
  • Do NOT spill water or cleaning agents on the unit's body or power plug. This can cause fire or electric shock.
  • Avoid high humidity environments. Do not install in areas where water may easily splash onto the unit. Ensure good ventilation in bathrooms.
  • Ensure proper electrical connection: The power outlet must be grounded, rated for 220V ± 10%, minimum 10A, and not exceed 2kW. The outlet should be located away from bathtubs and higher from the floor.
  • Beware of low-temperature burns from the heated seat, especially for children, the elderly, individuals with disabilities, or those under medication/intoxication. Adjust seat temperature accordingly.
  • Always disconnect power before cleaning or maintenance. Do not handle the power plug with wet hands.
  • Stop use immediately if any malfunction occurs: (e.g., clogging, cracks, smoke, overheating, strange odors, water leakage). Disconnect power and water supply.

⚠ CAUTION (Potential for Damage or Minor Injury)

  • Do NOT damage the power cord or seat connection cable. Do not bend, twist, pull, or place heavy objects on them.
  • If the power cord is damaged, it must be replaced by the manufacturer or a qualified service technician.
  • Use only the new hose provided for water connection.
  • Ensure the power plug is fully and securely inserted into the outlet.
  • Children should not play with the appliance.
  • Use only potable water for the unit.
  • Do NOT leave burning cigarettes or other hot objects near the unit.
  • Do NOT place heavy objects on the toilet lid.
  • Do NOT block the drying vent.
  • Do NOT twist or break the inlet hose.
  • Use neutral kitchen cleaners for cleaning; avoid harsh toilet cleaners, volatile substances, or banana oil.
  • Do NOT remove the water inlet filter when the water supply valve is open.
  • Do NOT flush anything other than human waste and toilet paper.
  • Ensure the water inlet valve is tightly secured during installation.
  • During thunderstorms, disconnect the power supply.
  • Do NOT use dry cloths or toilet paper to wipe the unit's body, lid, or seat, as this may cause scratches.
  • Avoid direct sunlight exposure to prevent discoloration and seat temperature reduction.
  • Do NOT force the lid or seat open or closed.
  • For long periods of disuse (e.g., travel), disconnect both water and power supplies.
  • Regularly clean the mesh filter if your local water quality is poor.
  • Do NOT urinate directly onto the nozzle or the unit's body.
  • Keep the remote control dry and replace batteries when the signal weakens.

2. Product Overview

The MEISHIDA 9917B Smart Toilet is designed to provide ultimate comfort and hygiene with its advanced features.

Key Features:

  • Fully Automatic Operation: Auto lid opening/closing, auto flush.
  • Instant Water Heating: Provides warm water for washing functions without delay.
  • Bidet and Feminine Wash: Adjustable water pressure, temperature, and nozzle position.
  • Warm Air Dryer: Adjustable temperature for comfortable drying.
  • Heated Seat: Adjustable temperature for comfort.
  • UV Sterilization: Ensures hygiene of the nozzle.
  • Night Light: Soft illumination for convenience in the dark.
  • Foam Shield: Creates a protective foam layer to prevent splashing and odors.
  • Dual Induction Seat: Enhanced sensor for user detection.
  • Wireless Remote Control: Easy access to all functions.

Product Components:

  • Smart Toilet Unit (with horizontal drain)
  • Toilet Lid
  • Wireless Remote Control with Mounting Bracket
  • Built-in Shut-off Valve
  • Foaming Liquid Reservoir
  • Backup Battery Pack
  • User Manual (this document)
Front view of the MEISHIDA Smart Toilet

Figure 2.1: Front view of the MEISHIDA Smart Toilet.

Overview of smart toilet features including automatic flush, heated seat, bidet, and dryer.

Figure 2.2: Key features of the smart toilet.

3. Setup and Installation

Installation should be performed by a qualified professional if you are unsure. Always ensure power and water are turned off before starting.

3.1 Pre-installation Preparation

Required Tools:

  • Adjustable Wrench
  • Level
  • Square Ruler
  • Sealant
  • Phillips Screwdriver
  • Hammer, Pencil or Marker
  • Electric Drill (for wooden floors) or Impact Drill (for concrete/tile floors)

Water and Electrical Requirements:

  • Water Pressure: Minimum dynamic pressure 0.1 MPa (17 L/min), maximum static pressure 0.75 MPa. Recommended system pressure is 3.5 bar.
  • Electrical: Connect to a grounded 220V ± 10%, 50Hz power outlet, minimum 10A. The power cord length is 1.2-1.5 meters. The outlet should be approximately 10 cm from the floor.

3.2 Installation Diagram

Installation diagram showing dimensions for power outlet, water inlet, and drain outlet.

Figure 3.1: Installation dimensions. Power outlet: 220V, 350-400mm high. Drain outlet: 240-280mm from wall, 150mm from center. Water outlet: 180mm from center.

3.3 Step-by-Step Installation

  1. Install Shut-off Valve: Install the provided shut-off valve onto the cold water supply pipe. If an old valve exists, remove it.
  2. Install Toilet Unit: Apply sealant to the top and bottom edges of the flange ring, then install it into the drain opening. Carefully place the toilet unit over the flange and drain.
  3. Connect Water Supply: Connect the water supply hose to the shut-off valve and tighten securely.
  4. Apply Sealant: After checking for any leaks and verifying all functions work correctly, apply sealant around the base of the toilet where it meets the floor. Do not use the toilet for at least 24 hours to allow the sealant to cure.

3.4 Electrical Connection

  1. Ensure the power outlet is grounded.
  2. Plug the toilet's power cord into the grounded outlet.
  3. Connect the backup battery pack to the toilet unit and install it in the designated compartment at the rear of the toilet.

3.5 Pre-Use Checks

  • Check that the spray nozzle and water pipes are not leaking. After drying all parts, check with absorbent paper.
  • Cover the seat presence sensor and check if an audible signal is heard.
  • Verify that the washing, drying, and flushing functions operate normally.
  • Check that the soft-closing buffer mechanism works correctly.
  • When testing cleaning and drying functions, ensure the seat presence sensor is activated.
  • When cleaning, cover the front part of the spray nozzle opening to prevent water from splashing out.

3.6 Remote Control Installation

  1. Clean and degrease the desired installation surface for the remote control bracket.
  2. Peel off the protective film from the double-sided tape on the back of the bracket and firmly attach it to the prepared surface.
  3. Install a new battery (not included) into the remote control.
  4. Place the remote control onto its mounting bracket.

4. Operating Instructions

The smart toilet is operated primarily via the wireless remote control. Some basic functions can also be accessed via side buttons on the unit.

4.1 Remote Control Functions

Remote control layout with various function buttons.

Figure 4.1: Example remote control layout (actual layout may vary slightly).

  • STOP: Turns off active washing/drying functions. Hold for 3 seconds to power the seat on/off.
  • REAR WASH: Activates bidet/rear wash. Press again for oscillating wash.
  • FEMININE WASH: Activates feminine wash. Press again to turn off.
  • DRYER: Activates warm air drying (default 3 minutes).
  • SEAT TEMP: Adjusts seat temperature (Room, 34°C, 37°C, 40°C).
  • WATER TEMP: Adjusts wash water temperature (Room, 34°C, 37°C, 40°C).
  • DRYER TEMP: Adjusts dryer air temperature (Room, 45°C, 50°C, 55°C).
  • WATER FLOW (+/-): Adjusts water pressure/flow rate (Levels 1-4).
  • NOZZLE POSITION (< >): Adjusts the nozzle position forward or backward.
  • FLUSH: Initiates a flush. The toilet also auto-flushes when the user leaves the seat.
  • LIGHT: Toggles the night light on/off.
  • LID: Opens or closes the toilet lid.

4.2 Hidden Functions & Adjustments

  • Foam Function: After sitting, a quiet motor sound indicates foam generation, creating a protective layer in the bowl.
  • Massage Wash: The nozzle extends, and water temperature alternates between warm and cool for a massage effect.
  • Auto Lid Lift (Foot Sensor): For models with this feature, a foot sensor at the base of the toilet can automatically lift the lid.
  • Remote Control Pairing: If needed, hold the REAR WASH button on the unit for 30 seconds until a beep, then press any button on the remote.
  • Sensor Range Adjustment: While the unit is idle, press STOP, then press FEMININE WASH. Adjust range from L1 (off) to L16 (max).
  • Lid Open Speed Adjustment: While idle, press STOP, then press WATER FLOW +/-. Adjust speed from C1 (slow) to C9 (fast).
  • Remote Sensitivity Adjustment: While idle, press STOP, then press NOZZLE POSITION +/-. Adjust sensitivity from S1 (light) to S9 (strong).
  • Flush Mode Adjustment: While idle, press STOP, then press FLUSH. Adjust flush strength from F1 (light) to F4 (strong).
  • Automatic Flush on Leaving: To enable/disable, hold the FLUSH button on the remote.
  • Automatic Bidet on Sitting: To enable/disable, hold the FEMININE WASH button on the remote.
  • Automatic Lid Close: To enable/disable, hold the LID button on the remote.

Video 4.1: Demonstration of smart toilet features and operation.

5. Maintenance and Cleaning

Regular cleaning and proper maintenance will ensure the longevity and hygiene of your smart toilet.

5.1 General Cleaning

  • Always disconnect power and turn off the water supply before cleaning or maintenance.
  • For regular cleaning of the toilet bowl, use soft sponges, brushes, cloths, and a mild soap solution.
  • For limescale and rust removal, use specialized cleaning agents according to their instructions. Do not leave them on the surface for extended periods.
  • To prevent static electricity and dust accumulation, wipe the unit with a damp cloth.
  • The toilet seat can be detached from the main body for easier cleaning.
  • Do not use dry cloths or toilet paper to wipe the unit's body, lid, or seat, as this may cause scratches.
  • Use neutral kitchen cleaners for cleaning; avoid harsh toilet cleaners, volatile substances, or banana oil.

5.2 Nozzle Cleaning

  • If the spray nozzle becomes dirty, use a small brush (like a toothbrush) to clean it.
  • Do not apply excessive force or pull the nozzle.
  • The nozzle can be extended manually for easier cleaning by pressing the dedicated button on the remote or unit.

5.3 Water Inlet Filter Cleaning

  • If your local water quality is poor, regularly clean the mesh filter to prevent clogging.
  • Do NOT remove the water inlet filter when the water supply valve is open.

6. Troubleshooting

If you encounter any issues, please refer to the table below before contacting customer support.

ProblemDiagnosisSolution
Unit does not operateNo power, leakage protector trippedCheck power connection, reset leakage protector. If problem persists, contact service.
No water spray from nozzleWater supply off, valve closed, filter clogged, pipe bentRestore water supply, open valve, clean filter, straighten pipe.
Weak spray intensityWater pressure setting, outlet filter cloggedAdjust water pressure setting, clean outlet filter.
Incorrect water temperatureTemperature setting, cold/warm massage onAdjust temperature setting, turn off massage function if not desired.
Remote control not workingLow batteryReplace remote control battery.
Seat not heatingTemperature setting, energy saving mode onAdjust seat temperature, turn off energy saving mode.
Lid/seat drops too fastDamper mechanism failureContact service for damper replacement.
Low flush pressureFilter clogged, low water pressure, pipe bentClean filter, check water supply pressure (0.15-0.75 MPa), straighten pipe.
No flush suctionAir in drain, S-trap blockedContact plumbing professional.
Dirty flush waterFlush valve failureContact service for flush valve replacement.

7. Specifications

FeatureSpecification
Rated VoltageAC 220V ± 10%, 50Hz
Rated Power1280W (Instant Heating Mode), 700W (Storage Heating Mode)
Water Flow Rate (Bidet/Feminine)Approx. 700 ml/min
Wash Water TemperatureRoom, 34°C, 37°C, 40°C (4 levels)
Water Heating MethodInstant Heating
Seat TemperatureRoom, 34°C, 37°C, 40°C (4 levels)
Seat Heater PowerApprox. 40W
Air Dryer TemperatureRoom, 45°C, 50°C, 55°C (4 levels)
Air Dryer PowerApprox. 220W (Max 350W)
Nozzle Movement Range1.5 cm
Inlet Water Temperature Range+5°C to +40°C
Water Pressure Range0.15 - 0.75 MPa (static)
Drainage PatternP-Trap (Wall Drainage by default)
MaterialCeramic
CertificationCE

Note: Wall drainage is used by default. If floor drainage is required, please contact customer service before purchase.

8. User Tips

  • Voice Control Language: Please note that the voice control function is in Chinese and is not available in English.
  • Optimal Flushing: Ensure your water supply meets the recommended pressure (0.15 - 0.75 MPa) for the best flushing performance.
  • Easy Installation: While installation is generally straightforward, always refer to the provided diagrams and instructions carefully. If unsure, consider professional installation.
  • Regular Cleaning: Disconnect power and water before any cleaning to ensure safety and prevent damage.

9. Warranty and Support

This product comes with a 1-year warranty from the date of purchase, covering manufacturing defects.

For technical support, warranty claims, or any questions not covered in this manual, please contact the seller or manufacturer directly.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.