1. Introduction
Thank you for choosing the JGINYUE B450M PLUS ARGB Motherboard. This micro-ATX motherboard is designed to support AMD Ryzen processors, offering a blend of performance, aesthetics, and essential features for both gaming and general computing. It features vibrant RGB lighting, reliable power delivery, and high-quality audio capabilities.
Important Notes:
- A WiFi Module is not included. We recommend the MT79212.
- This product may be shipped with either an ARGB or RGB version randomly.
2. Product Specifications

Figure 2.1: Detailed Product Specifications
| Feature | Details |
|---|---|
| Form Factor | Micro-ATX |
| Chipset | AMD B450 |
| CPU Support | Ryzen 1st, 2nd, 3rd Gen & Ryzen 5000 series (with BIOS update) |
| Memory | Dual-channel DDR4, up to 64GB |
| Expansion Slots | 1 PCIe x16, 1 PCIe x1 |
| Storage | 4x SATA 6Gb/s ports, 1x M.2 NVMe (PCIe 3.0) |
| USB Ports | Rear: 4x USB 3.0, 2x USB 2.0; Front: 1x USB 3.0, 1x USB 2.0 |
| Display Interfaces | HDMI, VGA, DP |
| Audio | 7.1-channel HD audio |
| LAN | Gigabit Ethernet (1x RJ45) |
| RGB Lighting | 5V ARGB / 12V RGB Headers |
3. Package Contents
The following items are typically included with your JGINYUE B450M PLUS ARGB Motherboard:
- JGINYUE B450M PLUS ARGB Motherboard
- SATA cable (x1)
- I/O Shield (x1)

Figure 3.1: Motherboard and Included Accessories
4. Interface Description
Video 4.1: JGINYUE B450M PLUS ARGB Motherboard Overview
4.1 Rear I/O Ports
The rear input/output (I/O) panel provides various ports for connecting peripherals. Refer to the image below for port identification.

Figure 4.1: Rear I/O Ports
- PS/2 Ports: Green for mouse, Purple for keyboard.
- USB Ports:
- Red: USB 3.2 Gen 2
- Blue: USB 3.2 Gen 1
- Black: USB 2.0
- USB4 (if present, check actual model)
- VGA (D-sub) Interface: Legacy video output, supports up to 1080P 60Hz.
- HDMI Interface: Video output, supports up to 4K 60Hz.
- DP Interface: Video output, supports up to 4K 240Hz.
- RJ45 Network Interface: Supports 1000/2500Mbps Ethernet. The indicator lights show network status:
Bandwidth Link Light Condition No connection Off 10Mbps Green light on 100Mbps Green light on 1000Mbps Orange light on 2500Mbps Orange light on Running Indicator Light: Off for no data transmission, Flashing for data transmission.
- Audio Interface:
- Green: Speaker output
- Pink: Microphone input
- Blue: Audio input
4.2 Onboard Pin Headers
These headers are for connecting internal components and front panel connectors.
- 1. Motherboard 4+4pin Port: For CPU power supply. Must be plugged in before turning on.
- 2. Motherboard 24pin Power Supply: For overall motherboard power. Must be plugged in before turning on.
- 3. F_PANEL Interface: Connects to front panel power switch, reset switch, HDD LED, and Power LED. Pay attention to positive and negative poles for LEDs.

Figure 4.2: Front Panel Header Pinout
- 4. USB 2.0 Interface: Front USB 2.0 pin header.

Figure 4.3: USB 2.0 Header Pinout
- 5. USB 3.0 Interface: Front USB 3.0 pin header.

Figure 4.4: USB 3.0 Header Pinout
- 6. Audio Interface: Front audio header, supports AC97 and HD audio.
- 7. COM Interface: Onboard serial output port, requires an adapter.
- 8. Fan 3/4pin Interface: For connecting case fans. 4-pin supports PWM speed control, 3-pin runs at full speed.
- 9. CLR CMOS: Jumper for clearing BIOS settings. Short the pins to clear CMOS data.
- 10. Speaker Pin: Used for power-on fault detection. The leftmost pin is positive.
- 11. 5V ARGB/12V RGB Header:
- 5V3 Pin ARGB: For connecting variable RGB lighting.
- 12V4 Pin RGB: For connecting monochromatic RGB lights.
- 12. ME Protect Pin: Some models have a 2-pin ME protection function. Short-circuit this when booting if the BIOS needs updating.
- 13. 5vSB Pin: Jumper for USB shutdown power supply. '12' is power-off, '23' is charged (for wake-up/charging). When charged, 5VSB can provide 2A current.
- 14. SATA 3.0 Interface: For connecting external SSDs or HDDs.
5. Installation Precautions
5.1 Security Information
WARNING: Components are sensitive to electrostatic discharge (ESD). Observe precautions to prevent damage.
- Ensure all components are firmly connected to prevent recognition issues or boot failures.
- When handling the motherboard, hold it by the edges to avoid touching sensitive components.
- Place the motherboard on an electrostatic shield or anti-static mat during installation.
- Do not power on the motherboard or start the computer before installation is complete, as this may cause permanent damage.
- Consult a professional computer technician if you need assistance.
- Before installing or removing any components, turn off the power and unplug the power cord from the outlet.
- Keep this product manual for future reference.
- Keep the motherboard away from humid environments.
- Before connecting to a power outlet, ensure the outlet provides the correct voltage.
- Route the power cord to avoid being stepped on or obstructed.
- Pay attention to all warning signs on the motherboard.
- If any of the following occur, take the motherboard to a maintenance technician: liquid penetration, moisture exposure, motherboard not working after troubleshooting, dropped/damaged motherboard, obvious signs of damage.
- Do not place the motherboard in an environment above 60°C (140°F).
5.2 RAM/Expansion Adapter Card Installation
CAUTION: Follow these guidelines for RAM and expansion card installation.
- Confirm that the memory specifications are supported by the motherboard. For optimal compatibility, use memory with the same capacity, brand, frequency, and chip.
- Carefully read the user manual and confirm expansion card compatibility.
- Turn off the power before installation to prevent damage.
- Memory sticks have a fool-proof design; they cannot be installed incorrectly.
- Install RAM into the DIMMA2 slot first.
- Due to chipset resource usage, the available memory capacity may be slightly less than the installed amount.
- When overclocking, memory module stability and compatibility depend on the installed CPU and device.
6. Setup and Installation
This section provides a general guide for installing components onto your motherboard. Always refer to the specific component manuals for detailed instructions.
6.1 CPU Installation
- Open the CPU socket lever.
- Carefully align the CPU with the socket, ensuring the gold triangle on the CPU matches the triangle on the socket.
- Gently place the CPU into the socket. Do not force it.
- Close the CPU socket lever to secure the CPU.
6.2 CPU Cooler Installation
Follow the instructions provided with your CPU cooler. Apply thermal paste if not pre-applied, then mount the cooler securely over the CPU.
6.3 RAM (Memory) Installation
- Open the clips on both ends of the DIMM slot.
- Align the memory module with the slot, ensuring the notch on the module matches the key in the slot.
- Press down firmly on both ends of the memory module until the clips snap into place.
- Install into the DIMMA2 slot first, then other slots as needed.
6.4 Storage Device Installation (M.2 / SATA)
- M.2 NVMe SSD: Insert the M.2 SSD into the M.2 slot at an angle, then push it down and secure it with the provided screw.
- SATA Drives: Connect SATA data cables from the motherboard's SATA 3.0 ports to your SSDs/HDDs. Connect SATA power cables from your power supply to the drives.
6.5 Graphics Card (PCIe) Installation
- Open the retention clip on the PCIe x16 slot.
- Align your graphics card with the slot and press down firmly until it clicks into place.
- Secure the card to your case with a screw.
- Connect any necessary PCIe power cables from your power supply to the graphics card.
6.6 Power Supply Connections
- Connect the 24-pin ATX power cable from your power supply to the 24-pin power connector on the motherboard.
- Connect the 4+4-pin CPU power cable from your power supply to the 4+4-pin CPU power connector on the motherboard.
6.7 Case Connections
Connect your case's front panel connectors (Power SW, Reset SW, HDD LED, Power LED, Front USB, Front Audio) to the corresponding headers on the motherboard as described in Section 4.2.
7. Operating Instructions
7.1 Powering On/Off
- Power On: Press the power button on your PC case.
- Power Off: Shut down your operating system normally. If unresponsive, press and hold the power button for 5-10 seconds.
7.2 Accessing BIOS/UEFI
To enter the BIOS/UEFI setup utility, power on your computer and repeatedly press the designated key (commonly DEL or F2) during the initial boot sequence. The BIOS allows you to configure system settings, boot order, and monitor hardware status.
7.3 Clearing CMOS (BIOS Reset)
If you encounter issues after changing BIOS settings, you can clear the CMOS to restore default settings. This can be done by:
- Using the CLR CMOS Jumper: With the system powered off and unplugged, locate the CLR CMOS jumper (refer to Section 4.2, item 9). Move the jumper cap from pins 1-2 to 2-3 for a few seconds, then return it to 1-2.
- Removing the CMOS Battery: With the system powered off and unplugged, remove the small coin-cell battery (CR2032) from the motherboard for about 1-5 minutes, then reinsert it.
8. Maintenance
- Dust Cleaning: Regularly clean dust from your PC case and motherboard components using compressed air. Ensure the system is powered off and unplugged before cleaning.
- BIOS Updates: Periodically check the JGINYUE website for BIOS updates. BIOS updates can improve compatibility, stability, and performance. Follow the update instructions carefully. If your model has an ME Protect Pin, refer to Section 4.2, item 12 for BIOS update procedures.
- Connection Checks: Occasionally check that all cables and components are securely seated to prevent intermittent issues.
9. Troubleshooting
- No Power:
- Check if the 24-pin ATX and 4+4-pin CPU power cables are securely connected to the motherboard and power supply.
- Verify that the front panel power switch is correctly connected to the F_PANEL header.
- Ensure the power supply is switched on and receiving power from the wall outlet.
- No Display:
- Ensure the graphics card is properly seated in the PCIe slot and any necessary power cables are connected.
- Verify that the monitor cable is connected to the graphics card (or motherboard if using integrated graphics).
- Reseat RAM modules. Try booting with only one RAM stick.
- System Instability/Crashes:
- Check CPU cooler installation and ensure proper thermal paste application.
- Verify RAM modules are correctly installed and compatible.
- Ensure your power supply provides sufficient wattage for all components.
- Run memory diagnostic tools to check for faulty RAM.
- BIOS Issues:
- If the system won't boot after changing BIOS settings, clear the CMOS to revert to default settings (see Section 7.3).
10. User Tips
- CPU Compatibility: This motherboard is compatible with Ryzen 7 5700x processors. Ensure your BIOS is updated to the latest version for optimal support of newer Ryzen CPUs.
- Cable Management: Proper cable management not only makes your build look cleaner but also improves airflow within the case, contributing to better cooling and system stability.
- Driver Installation: After installing your operating system, remember to install the latest drivers for your chipset, LAN, audio, and any other components from the JGINYUE website or the included driver disc.
11. Warranty and Support
11.1 Warranty Statement
JGINYUE Technology provides a one-year warranty for this product from the date of purchase. Our seller will provide repair service within this period for problems listed in the Microcomputer Performance Failures Table published by the CCIA.
Limitations and Exclusions:
- Man-made damages to the CPU, Chipset, or other parts will incur replacement and repair costs, to be borne by the buyer.
- Warranty is unavailable in the following cases:
- Inability to provide proof-of-purchase.
- Product is found to be trouble-free after testing.
- Warranty has expired.
- Man-made damages such as missing components, bent/scratched PCB, oxidation/corrosion, or burned components due to incorrect usage.
- Altered, lost, removed, or damaged Barcode/Serial number/Model label/Anti-disassembly label.
- Damage caused by irresistible forces (e.g., water immersion, fire, lightning).
- Motherboard damage due to insecure packaging or improper transportation during repair.
- Damage caused by unauthorized personnel disassembling or replacing components (e.g., CPU IHS cover, VRM Heatsink).
- If a defective product is discontinued, a similar product may be offered at a discounted price (price differences may apply).
Note:
- Warranty details may vary according to local laws outside of the PRC.
- JGINYUE reserves the right of interpretation of this statement.
11.2 Product Statement
The copyright of this manual belongs to JGINYUE Technology. JGINYUE Technology reserves the right to add and delete content without prior user notification. This manual is a technical document and does not imply or map to any third-party content. Any ambiguity due to typographical errors is disclaimed.
Abnormal Warranty Coverage:
- Malfunctions and damages caused by improper use, installation, self-disassembly, part replacement, or arbitrary changes in specifications are not covered.
- Any product changes, modifications, or indirect/special/accidental damages are not covered.
Environmental Conditions:
Avoid using this product in environments with high temperature, low air pressure, low temperature, high humidity, dust, strong magnetic fields, and long-term exposure to sunlight. We recommend use in an environment with an altitude of less than 3,000 meters, temperature between 0°C to 35°C, and humidity between 5% to 95%.
11.3 Contact Information
For technical support or warranty inquiries, please contact us:
- Email: sales@t-diagtech.com
A detailed user manual in PDF format is available for download: JGINYUE B450M PLUS User Manual (PDF)