Xiaomi BE3600

Contents

Xiaomi BE3600 Router User Manual

Model: BE3600 (RN06)

1. Product Overview

Read this manual carefully before use, and retain it for future reference.

Front view of the Xiaomi BE3600 Router

Figure 1: Front view of the Xiaomi BE3600 Router.

Rear view of the Xiaomi BE3600 Router showing ports

Figure 2: Rear view of the Xiaomi BE3600 Router with labeled ports.

1.1. Components and Functions

No.ComponentFunction
1Power portConnect the power adapter to the router.
2Reset buttonPress and hold the button for 5 seconds to restore the router to its factory settings.
31G Network port3 × 10/100/1000 Mbps WAN/LAN auto-sensing port.
42.5G Network port1 × 10/100/1000/2500 Mbps WAN/LAN auto-sensing port.
5Mesh buttonPress the button to have Mesh networking with routers that support the Xiaomi Mesh function.

Note: Illustrations of product, accessories, and user interface in the user manual are for reference purposes only. Actual product and functions may vary due to product enhancements.

2. Specifications

2.1. General Specifications

AttributeValue
NameXiaomi Router BE3600
ModelRN06
Input12 V = 1.5 A
CPUQualcomm Quad-core 1.1GHz CPU
RAM256MB
Wired Technology1 × 10/100/1000/2500M adaptive WAN/LAN port
3 × 10/100/1000M adaptive WAN/LAN port
Wireless Technology2.4G Wi-Fi: 2 x 2 MAX 688Mbps
5G Wi-Fi: 4 x 4 MAX 2882Mbps
Antenna4 x external high gain antennas
Heat dissipationNatural heat dissipation
Power ConsumptionNetworked standby mode: ≤ 7.2 W (8.1 W if all wired ports connected and wireless ports activated)
Time to Enter the ConditionNetworked standby mode: ≤1 min
Operating Temperature0°C to 40°C
Storage Temperature10% ~ 90% RH non-condensing
Operating Humidity-40 ~ 70 ℃
Storage Humidity5% ~ 90% RH non-condensing

2.2. Wireless Channels

  • 2.4GHz: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13
  • 5GHz: 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165

2.3. Dimensions

Dimensions of Xiaomi BE3600 Router: 209.98mm width, 219.83mm height, 40.95mm depth

Figure 3: Router dimensions (approx. 210mm x 220mm x 41mm).

2.4. Plug Options

Image showing US plug and adapters for EU, AU, UK

Figure 4: Available power plug options.

  • US Plug: Original CN/US Plug
  • EU Plug: US plug + EU switch plug adapter
  • AU Plug: US plug + AU switch plug adapter
  • UK Plug: US plug + UK switch plug adapter

3. Setup

3.1. Network Configuration

Preparation before Configuration

  1. Connect the router to power; the router will automatically turn on.
  2. Restart your modem. (Note: The modem is provided by your Internet service provider.)
  3. Plug one end of the network cable into either of the router's ports, and the other end into the LAN port of the modem. (Note: If you use the Ethernet wall socket instead of the modem, directly plug the network cable into it.)
Diagram showing router connected to modem and power

Figure 5: Basic network connection diagram.

Method 1: Network Configuration via Xiaomi Home App

  1. Scan the QR code below to download the Xiaomi Home app, or search for "Xiaomi Home" in your app store to download and install it.
  2. Open the Xiaomi Home app, tap "+" on the upper right, choose the correct product model, and then follow the instructions to complete the network configuration.
Xiaomi Home app interface with QR code and plus button

Figure 6: Xiaomi Home App for setup.

Note: The version of the app might have been updated; please follow the instructions based on the current app version.

Method 2: Network Configuration via Web Browser

  1. Check the Wi-Fi name on the label at the bottom of the router and then connect your phone or computer to that Wi-Fi network.
  2. An automatic redirection will take you to the network setup page. If not, open your web browser and enter miwifi.com or 192.168.31.1. (Note: When using the HTTPS protocol, a warning message may be prompted on the webpage. However, the connection between the browser and the Xiaomi router's settings page (miwifi.com) is safe.)
  3. Follow the instructions on the setup page to complete the network configuration. (Note: Contact your Internet service provider to get the details if you are not familiar with the Internet connection type.)
  4. After the configuration of the router is completed, the Wi-Fi module will restart. Try to search for the Wi-Fi again later.

3.2. Xiaomi Mesh Networking

Xiaomi Mesh networking technology supports Mesh networking of up to 10 routers to achieve broader network coverage. For compatible router models and software versions, visit www.mi.com.

Method 1: Mesh Networking via Xiaomi Home App

  1. Open the Xiaomi Home app.
  2. Go to the "Mesh network devices" page of the main router.
  3. Tap "+" on the upper right corner of the page.
  4. Follow the instructions to complete Mesh networking.
  5. When the Mesh networking is completed, the indicator of the satellite router turns blue.
Diagram showing multiple Xiaomi routers forming a mesh network

Figure 7: Mesh networking setup via Xiaomi Home App.

Method 2: Mesh Networking via Mesh Button

  1. Make sure the main router is connected to the network. Connect the satellite router to power and place it near but at least one meter away from the main router. Otherwise, they will interfere with each other and affect the networking.
  2. After the satellite router powers on, the main router will automatically discover it, and the indicator of the main router will start breathing blue. (Note: If the satellite router is already configured, press its reset button to restore it to the factory settings first.)
  3. Press the mesh button on the main router, and the indicators of the main router and satellite router will start blinking. It will take about 2 minutes to complete the Mesh networking.
  4. When the Mesh networking is completed, the indicator of the satellite router turns blue.
Close-up of the router showing the Mesh button

Figure 8: Mesh button on the router.

Method 3: Mesh Networking via Network Cable

  1. Make sure the main router is connected to the network. Place the satellite router in the location where you need Wi-Fi coverage and power it on.
  2. Connect any port of the satellite router and any port of the main router via a network cable. The indicators of the main router and satellite router will start blinking. It will take about 2 minutes to complete the Mesh networking.
  3. When the Mesh networking is completed, the indicator of the satellite router turns blue.
Diagram showing two routers connected via network cable for mesh networking

Figure 9: Wired mesh networking connection.

4. Operation

4.1. Indicator Status

Indicator StatusDescription
OffThe router is off or unplugged.
OrangeThe system is starting up or a network connection error occurred.
Blinking orangeThe newly added satellite router is connecting to the Mesh networking or the system is updating.
Breathing orangeThe router is started and the system is ready for configuration.
BlueThe router is working properly.
Breathing blueA new satellite router is discovered. The indicator will automatically turn blue if there is no operation for Mesh networking within 2 minutes.
Blinking blueThe satellite router is connecting to the main router.

5. Troubleshooting

IssuePossible Cause and Solution
I cannot access the internet.
  • Make sure the network cable is plugged into the Ethernet port of the modem. If your modem has multiple Ethernet ports, leave the others unplugged.
  • Turn off your modem and wait for 5 minutes, then turn it on and have a reset.
  • Directly connect a computer to the modem via a network cable to check if the internet is working. If not, contact your Internet service provider.
  • Log in to the router's web management page, and go to the Network Settings to verify the internet IP address. If valid, set your primary DNS to 8.8.8.8, and secondary to 8.8.4.4. If invalid, make sure the hardware connections are connected properly or contact your Internet service provider.
My wireless devices cannot connect to the Wi-Fi.
  • Ensure the Wi-Fi name and password do not contain special characters during configuration.
  • Make sure the Wi-Fi you selected and the password you entered are correct.
  • Verify if your device is blacklisted. If yes, remove it from the blacklist to allow connection.
  • Choose WPA2 encryption for your router to enhance compatibility.
  • Restart both your router and device then try again.
I forget the management password or Wi-Fi password of the router.Restore the router to factory settings, and set up a new management password or Wi-Fi password.
I cannot add the router in Xiaomi Home app.
  • Check if your phone has connected to the Wi-Fi of the router.
  • Check if the selected product model is correct in Xiaomi Home app.
  • Make sure that the settings of country or region in Xiaomi Home app is not Chinese mainland.
I have already added the router to the app, but there is still a pop-up for adding this router.The server is changed after you alter the settings of country or region. You may:
  • Ignore the request of adding the router. The router will not appear in the list of Xiaomi Home app, and the related functions within the app will not be available under the current settings unless you change back to the original settings of country or region.
  • Add the router. You can use the functions of the router within the app in the current settings. However, the information on the original server will be cleared, and you need to add the router again if changing back to the original settings of country or region.

6. User Tips

  • The setup process for the Xiaomi BE3600 Router is generally simple and straightforward.
  • Users report stable performance and good signal coverage throughout their homes.
  • For advanced management and integration with other smart devices, utilize the Xiaomi Home App.

7. Regulatory Compliance Information

7.1. Operating Frequency

  • Wi-Fi: 2412 MHz-2472 MHz, 5150 MHz-5350 MHz, 5470 MHz-5725 MHz

Note: 5650-5725 MHz is not authorized in Malaysia.

7.2. EU Declaration of Conformity (CE)

Hereby, Beijing Xiaomi Electronics Co., Ltd. declares that the radio equipment type RN06 is in compliance with Directive 2014/53/EU, Directive 2011/65/EU and Directive 2009/125/EC. The full text of the EU declaration of conformity is available at the following internet address: http://www.mi.com/global/service/support/declaration.html

7.3. WEEE Information

All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.

7.4. RF Exposure Warning

To comply with CE RF exposure requirements, the device must be installed and operated 20 cm (8 inches) or more between the product and all person's body. Operation of this equipment in a residential environment could cause radio interference. The power adapter shall be installed near the equipment and easily accessible. Refer to the detailed product specifications on the label at the bottom of the device.

Warning: Operation of this equipment in a residential environment could cause radio interference. This device is restricted to indoor use only when operating in 5150–5350 MHz frequency range in following countries: AT, BE, BG, HR, CY, CZ, DK, EE, FI, FR, DE, EL, HU, IE, IT, LV, LT, LU, MT, NL, PL, PT, RO, SK, SI, ES, SE, UK (NI), IS, LI, NO, CH, TR.

7.5. FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

7.6. FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

8. Warranty and Support

For warranty information and technical support, please refer to the official Xiaomi website or contact your local Xiaomi service center. A detailed user manual is also available in PDF format: Download PDF User Manual.

For firmware updates, please visit https://www.mi.com/global/support/faq/details/KA-348402.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.