HYULIGHTS HYU-300B

Contents

300W Mini Beam Moving Head Light User Manual

Model: HYU-300B

1. Introduction

Thank you for choosing the HYULIGHTS HYU-300B 300W Mini Beam Moving Head Light. This professional moving head light is a powerful and versatile device designed for stage and DJ applications. To ensure your safety and optimal performance, please read this user manual carefully before installation and operation.

Upon unpacking, you should find the following items:

  • One HYU-300B Moving Head Light
  • One Power Cable
  • One User Manual (this document)
  • One DMX Cable
  • Two Omega Brackets

Please inspect all components for any damage caused during transportation. If any damage is found, do not install the device and contact your dealer immediately.

Product packaging and included accessories
Figure 1: Product packaging and included accessories

2. Safety Precautions

For your safety and the longevity of the device, adhere to the following precautions:

  • Installation and operation should only be performed by certified technicians.
  • Mount fixtures in areas inaccessible to unauthorized personnel, away from walking paths or seating areas.
  • This lamp is for professional use only.
  • Ensure the power supply voltage matches the equipment's requirements (AC100-240V, 50/60Hz).
  • Avoid placing the product in locations prone to loosening or vibration.
  • Discontinue use immediately if the lamp operates abnormally.
  • Do not expose the product to humid or leaking environments, or temperatures exceeding 60°C.
  • Power supply voltage fluctuations should not exceed ±10%. Excessive voltage can shorten bulb life, while low voltage can affect light color.
  • Allow the lamp to cool down for at least 20 minutes after power-off before restarting.
  • Regularly check rotating parts and accessories for looseness; reinforce as needed to prevent accidents.
  • CAUTION: This product uses a high-voltage bulb requiring a ballast. It takes approximately one minute for the bulb to reach optimal performance. Keep the device away from rain and moisture. Always unplug the mains lead before opening the housing.
  • The installation area must support a minimum point load of 10 times the device's weight.
  • Always secure the fixture with a secondary safety attachment, such as a safety cable.
  • Never stand directly below the device during mounting, removal, or servicing.
  • Maintain a minimum distance of 0.5m (1.5ft) from flammable materials.

3. Product Overview & Key Features

The HYU-300B is a versatile moving head light with advanced features for dynamic lighting effects.

HYULIGHTS HYU-300B Mini Beam Moving Head Light
Figure 2: HYULIGHTS HYU-300B Mini Beam Moving Head Light

Key Features:

  • 300W Power: High-intensity light output.
  • Halo Effect: Features 24pcs RGB 3in1 5050 LEDs for dynamic halo effects.
  • 360° Dynamic RGB Effect: Vivid lighting with 31 full-color LEDs.
  • 152MM Lens: Precision optics for sharp beams.
  • Advanced Cooling & Durable Build: High-efficiency cooling system, flame-retardant and high-temperature resistant plastic shell, and durable metal frame ensure stable, long-lasting operation.
  • DMX512/RDM & LCD: Supports DMX/RDM protocol with an intuitive LCD display for easy adjustment and seamless integration.
  • Pan/Tilt Scan: 540° Pan and 270° Tilt with 16-bit electric correction.
  • Prism: 1pcs 48 rotating prisms for complex beam patterns.
  • Gobo Wheel: 14 gobos with shake and infinite rotating speed.
  • Color Wheel: 13 colors with infinite rotating speed.
  • Zoom Beam Angle: Adjustable from 1.5° to 15°.
  • Strobe: Up to 25 times/second.
  • Dimmer: 0-100% mechanical step.
  • Operating Modes: Auto mode, Sound mode, Master&Slave, RDM.
  • Protective Class: IP20.
Key Features Diagram
Figure 3: Key Features Overview
Advanced Cooling and Durable Build Diagram
Figure 4: Advanced Cooling and Durable Build
360 Dynamic RGB Effect Diagram
Figure 5: 360° Dynamic RGB Effect

4. Setup and Installation

4.1 Mounting Points

Overhead mounting requires specialized knowledge. If you lack the necessary qualifications, do not attempt installation yourself to avoid injury. Ensure all rigging and installation procedures are complete before connecting to power.

4.2 Clamp Mounting

The moving head light features a unique mounting bracket assembly at the bottom of the base, which includes 'omega brackets' and a safety cable rigging point. When mounting to a truss, securely attach an appropriately rated clamp to the omega bracket using an M10 screw through its center hole. Always attach at least one properly rated safety cable to the integrated rigging point in the base assembly as an additional safety measure.

Mounting bracket assembly diagram
Figure 6: Mounting Bracket Assembly

4.3 DMX-512 Control Connection

Connect the provided XLR cable from the female 3-pin XLR output of your DMX controller to the male 3-pin XLR input of the moving head. Multiple moving heads can be daisy-chained using serial linking. Use a two-core, screened cable with XLR input and output connectors.

DMX-512 control connection diagram
Figure 7: DMX-512 Connection Diagram

4.4 DMX-512 Connection with DMX Terminator

For long DMX cable runs or in electrically noisy environments (e.g., discotheques), a DMX terminator is recommended to prevent signal corruption. A DMX terminator is an XLR plug with a 120Ω resistor connected between pins 2 and 3, plugged into the output XLR socket of the last fixture in the chain.

DMX terminator connection diagram
Figure 8: DMX Terminator Connection

5. Operation

5.1 LED Screen Function

The device features an LED display for control and monitoring. The display shows DMX signal status, sound indicator, menu navigation, and system status.

LED display panel with buttons
Figure 9: LED Display Panel and Buttons

Button Description:

  • DMX: DMX Signal indicator
  • ERR: Sound indicator
  • Up/Down/Left/Right: Menu navigation and selection
  • OK: Confirm button

The display also shows total system usage time and power-on time. A green dot in the upper right corner indicates normal operation; a red dot indicates an error (viewable in 'Information Menu/Error Information/View').

UI color styles on LED display
Figure 10: UI Color Styles on LED Display

5.2 Menu Tree and Description

SettingOptions/RangeDescription
Default setEnterRestore factory default parameters
Address001-512DMX512 address
DMX modeModel, Mode2Select DMX control mode
Effect modeNo/YesEffect disk automatically finds shortest distance to rotate
Started lampOff/onChoose whether lamp turns on/off with activation
Switch lampOff/onManually turn on the light bulb
No signalClear, HoldKeep DMX value or clear DMX channel value when no DMX signal
UI ColorGreen, GoldenSelect screen background color
Show timeNo/YesDisplay running time counter on main interface
Brightness000-255Adjust screen brightness
ScreensaverOff/onTurn off screen when no key is pressed
XY encoderNo/YesCancel or use XY automatic correction
X/Y inversionNo/YesX/Y-axis forward or reverse operation
Focus inversionNo/YesFocus axis runs forward or reverse
Zoom inversionNo/YesZOOM axis runs forward or reverse
Run modeDMX/Auto/SoundMode Selection
Run speed255Set the running speed
Run cross255Automatic or voice-activated sliding steps

5.3 Manual Control and Programming

The device supports programming up to 4 user programs (PRO1-PRO4) that can run in series or individually. Programming functions include selecting, reading, copying, pasting, clearing, and saving steps.

To manually control the device, select the 'Manual/Console Mode' on the display. Double-click the desired channel to highlight it, then use the slider or up/down arrows to adjust the value.

Manual control interface on LED display
Figure 11: Manual Control Interface

For DMX console control programming, select 'Console' mode. All channel values are input via the DMX console. To program, click the next number and press the up arrow. Programs can be saved to PRO1-PRO4 positions. Existing programs can be read out, re-edited, and saved.

To run a saved program, navigate to the 'Test Run/Perform' function menu, select the corresponding user program, and switch it to 'On'.

5.4 Product Demonstration Video

Watch this video for a visual demonstration of the moving head light's features and effects.

Video 1: HYULIGHTS HYU-300B Moving Head Light Demonstration

6. Technical Specifications

ParameterValue
VoltageAC100-240V, 50/60Hz
Power Dissipation450W
Lamp290W 14R (Color temperature: 9300K)
Halo Effect24pcs RGB 3in1 5050 LEDs
Channel Mode16 DMX512 Channel
Pan Scan540° (16bit) Electric correction
Tilt Scan270° (16bit) Electric correction
Strobe25 times/sec
Prism1pcs 48 rotating prisms
Other EffectFrost and 6in1 rainbow effect
Zoom Beam Angle1.5°-15°
Color Wheel13 colors + color rotating speed (infinite rotating)
Gobo Wheel14 gobos + shake + Gobo Rotating speed (infinite rotating)
Dimmer0-100% mechanical step
FeaturesAuto mode, Sound mode, Master&Slave, RDM
HousingHigh temperature resistant plastic shell
Protective ClassIP20
Display BoardLED display
Net Weight (N.W)9KG
Gross Weight (G.W)11KG
Product Size48*28*20cm
Packing Size50*36*36.5cm

6.1 DMX Channels

ChannelFunctionChannel Value
1Pan000-255
2Tilt000-255
3Pan fine000-255
4Tilt fine000-255
5Pan Tilt speed000-255
6Frost / Rainbow effect000-079: No effect
080-159: Frost Effect
160-255: Rainbow effect
7Strobe000-003: Strobe Off
004-103: Strobe Speed Slow - Fast
104-107: bulb on
108-207: Pulse Strobe Slow - Fast
208-212: bulb on
213-251: Random strobe slow - fast
252-255: bulb on
8Dimmer000-255: mechanical step
9Color000-003: White
004-007: Half Color
008-011: Color 1
012-015: Half Color
016-019: Color 2
020-023: Half Color
024-027: Color 3
028-031: Half Color
032-035: Color 4
036-039: Half Color
040-043: Color 5
044-047: Half Color
048-051: Color 6
052-055: Half Color
056-059: Color 7
060-063: Half Color
064-067: Color 8
068-071: Half Color
072-075: Color 9
076-079: Half Color
080-083: Color 10
084-087: Half Color
088-091: Color 11
092-095: Half Color
086-099: Color 12
10Color Fine-tuning000-127: No effect
000-127: Color Fine-tuning
128-191: Color rotation from slow to fast
192-255: Color inversion from slow to fast
11GOBO000-008: Gobo 1
...
117-127: Gobo 14
128-191: Gobo rotation from slow to fast
192-255: Gobo inversion from slow to fast
12GOBO shake001-191: Shake speed
192-255: No effect
13Zoom000-255
14Prism0-255
15Prism rotation000-127: Prism ON
128-191: prism rotates from fast to slow
192-255: Prism inversion from slow to fast
16Lamp Control and Reset000-099: No effect
100-105: bulb delay off
106-149: No effect
150-155: bulb at half power (if applicable)
156-199: No effect
200-205: bulb delay on
206-254: No effect
255-255: Reset after a few seconds
CH17LED Halo Dimmer Strobe0-9: No function
10-49: Open
50-89: Strobe from slow to fast
90-129: Pulse strobe from slow to fast
130-249: Random strobe from slow to fast
CH18LED Halo Effect250-255: Open
0-255
CH19LED Effect Speed0-127: LED Effect Speed
0-127: LED Effect Speed Reversal

7. Maintenance and Cleaning

Regular maintenance and cleaning are crucial for optimizing light output and extending the device's lifespan.

7.1 General Maintenance

  • Intermittent use helps extend the lamp's life.
  • Do not use alcohol or any other organic solvent to clean the shell.
  • Regularly check rotating parts and adhesive accessories for looseness.
  • If any damage or missing parts are found, repair or replace them to prevent accidents.
  • The continuous use time of the lamp should not exceed 4 hours. Use alternative operations to prevent shortening the lamp's service life.
  • Always disconnect the power supply before maintenance or lamp removal.
  • Allow parts to cool for at least 10 minutes before handling after operation.

7.2 Cleaning Procedures

The frequency of cleaning depends on the operating environment. Humid, smoky, or dirty environments require more frequent cleaning.

  • Clean internal and external optical lenses and mirrors regularly to optimize light output.
  • Use a soft, lint-free cloth with a common glass cleaning fluid.
  • Always dry parts carefully after cleaning.
  • Clean external optics at least every 20 days, and internal optics every 30-60 days.
  • Clean the fan and ventilation equipment every 15 days.
  • Do not use solvents on the dichroic filter, as this will cause damage.
  • Clean the hot barrel at least every two weeks to prevent dirt accumulation.
  • After using the bulb, check and clean any waste paper or debris in the air inlet to prevent windmill malfunction and fire.

8. Troubleshooting

Below are common problems and recommended solutions. For unapproved issues, always consult professionals.

8.1 General Troubleshooting

  • No Power: Check power supply connection, switch, and ensure the lamp is suitable.
  • Lamp Not Working: Check if the lamp has reached its service life (replace if necessary), measure power supply, and ensure proper operation (wait 30 mins for cooling before connecting power).
  • DMX Control Issues: Check DMX 512 controller 'turn on' command, trigger circuit connection, connecting cable, temperature switch, and resistance of 'WK' socket.

8.2 Dark or Uneven Beam

  • If the lamp has reached its service life, replace it.
  • Clean the reflector part.
  • Measure if the power supply is sufficient.
  • Make small adjustments to height or screw system to achieve the ideal beam.

8.3 Light Shadow Fogging

  • Check DMX512 controller data for electric focus.
  • Check for blocked mechanical parts; clean and add high-temperature resistant oil if necessary.

8.4 Intermittent Light

  • Check if the fan is running normally or if there is any blockage.
  • Check if the heat sink is blocked.
  • Check if the lamp has reached the end of its service life.
  • Ensure power supply and circuit connections are good.
  • Check the low-temperature switch.

8.5 Light On, But No Control Commands

  • Check communication control line connection (not too long or interrupted).
  • Verify control system effectiveness and signal amplifier.
  • Ensure the signal line uses shielded twisted pair (resistance 75Ω).
  • Check lamp end and terminal resistor.
  • If the lamp is not cooled enough, improper operation can cause high voltage leakage, damaging the circuit or communication IC/CPU; replace PCB board if necessary.
  • Verify start code address and function options are correct.

8.6 Stage Lights Not Moving

  • Check if the power supply is suitable for the lamp voltage data.
  • Check if the input voltage fuse is defective.
  • Inspect for deformation, internal damage, or dampness causing poor contact.
  • Check for loose internal leads and connectors.
  • Verify electrical components (switches, transformers, ballasts, capacitors, varistors, filters, PCB boards, controllers to motors) are not short-circuited or burned.

8.7 Some Projectors Cannot Respond to Control Commands

  • Check if the motion command is correct.
  • Check for deformed or loose mechanical parts.
  • Verify motor socket function and driver chip.
  • Check if the motor wire is cut.
  • Check if the motor function is damaged.

8.8 Pan/Tilt Not Working Properly

  • Check for broken X.Y belt.
  • Check if the receiver X/Y direction data is damaged.
  • Reset the stage light machine.

9. User Tips

  • For best effects, consider pairing this moving head light with a fog machine to enhance beam visibility.
  • When setting up multiple lights, ensure consistent DMX addressing and termination for reliable control.
  • Experiment with different gobo and prism combinations to create unique visual patterns for your events.
  • Utilize the auto and sound modes for quick setup in less complex environments, or for dynamic effects synchronized with music.

10. Warranty and Support

Your HYULIGHTS HYU-300B Moving Head Light comes with a 2-year warranty from the date of purchase. This warranty covers manufacturing defects and quality problems. In case of any quality issues, new items will be sent for free or a full refund will be provided.

We offer a 30-day full refund guarantee if you are not completely satisfied with your purchase. Simply inform us within 30 days for an unconditional full refund.

For any inquiries or support needs, our customer service team provides quick responses within 12 hours. We appreciate it if you can provide a video or pictures to help us understand and resolve your issue efficiently.

For further details, you may refer to the official user manual PDF available at: User Manual (PDF)

Customer Service details: 30-day refund, 12-hour response, friendly reminder, 2-year warranty
Figure 12: Customer Service Details

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.