1. Important Safety Instructions and Warnings
Please read this manual carefully before using the product to ensure safe and correct operation.
1.1 General Safety
- Do not allow children to operate this product. Users with physical, sensory, or psychological disorders, or those who lack knowledge of the functions and operation of this product must be supervised by a fully competent user after being familiar with the use procedures and safety risks.
- This product is designed for cleaning framed windows and glass. It is not suitable for frameless windows or glass.
- If the window or glass frame has a damaged silicone rubber edge, exercise caution as the machine may leak and fall off.
- Always observe the using scenario to ensure the product is used safely and securely.
1.2 Electrical Safety
- Use only the original adapter. Using a non-original adapter may cause product failure or damage.
- Ensure the adapter has enough space for ventilation and heat dissipation. Do not wrap the power adapter with other objects.
- Do not use the adapter in a humid environment or touch it with wet hands.
- Charge the window cleaner at the voltage the power adapter can withstand (100-240V).
- Do not use a damaged power adapter, charging cable, or power plug.
- Before cleaning and maintaining the machine, unplug the power plug. Do not disconnect power by unscrewing the extension cord.
- Do not disassemble the power adapter. If faulty, replace the entire adapter. Contact customer service for assistance.
1.3 Battery Safety
- The product battery, if not handled properly, poses a risk of combustion or chemical injury. Do not disassemble the battery.
- Do not use or store in fire or high-temperature environments above 60°C.
- Hand over used batteries to a local professional waste battery product recycling center.
- The built-in battery can only be replaced by the manufacturer or designated service center.
1.4 Usage Environment
- Do not immerse this product in liquids (such as beer, water, drinks, etc.) or leave it in a humid environment for a long time.
- Do not expose this product to direct sunlight or heat sources (radiators, heaters, microwave ovens, gas stoves, etc.).
- Do not place this product in a strong magnetic field.
- Store this product out of reach of children.
- Use this product in ambient temperatures between 0°C and 40°C (32°F and 104°F).
- Do not clean damaged glass or objects with uneven surfaces, as the vacuum suction may be insufficient.
- Remove any items on the glass surface before use.
- Keep hair, loose clothes, fingers, or other body parts away from the working parts of the machine.
- Do not use the machine in areas with flammable and explosive solids or gases.
2. Product Description
The DIVEDEER YTK334 Window Cleaning Robot features a powerful vacuum motor that allows it to adhere securely to glass surfaces and move freely. It incorporates a backup battery for power failure protection, preventing falls during unexpected power interruptions. The robot is equipped with two cleaning wheels with suction cups, which absorb onto the glass and facilitate movement. The cleaning cloths are made of microfiber and are easily replaceable, ensuring effective cleaning. With its 4.0 Artificial Intelligence System, the robot can plan cleaning paths, detect frames, and automatically clean entire windows. A remote control provides manual operation for precise control.
2.1 Key Features
- • Micron Atomized Impregnation for effective water spray.
- • UPS Power Failure Protection with a 20-minute backup battery.
- • Bezel Sensing for intelligent navigation.
- • One-Button Remote Command for ease of use.
- • Artificial Intelligence Systems for smart cleaning.
- • Route Planning with three distinct cleaning modes.
- • Imported Brushed Motor for reliable performance.
- • Metal Impeller for durability.
- • Microfiber Cloths for superior cleaning.
- • Dual Plate Dual Suction for tight cleaning.
- • Ultrathin 9.5cm body for wider application range.
- • 30ML Large Water Tank for fog condensation dust removal.



3. Setup
3.1 Power Connection
- Connect the AC power cord to the adapter.
- Insert the threaded connector into the power connector of the robot's fuselage and tighten it securely.
- Plug the power cord into a power socket.
The device has a built-in battery for standby power supply in case of power failure. Ensure the battery is fully charged before use (green light indicates full charge). When connecting the power cord, the orange light indicates charging.

3.2 Installing the Cleaning Cloth and Ring
Ensure the cleaning cloth is placed correctly on the cleaning ring, and the cleaning ring is correctly attached to the cleaning wheel to prevent air leakage.
3.3 Attaching the Safety Rope
- For glass doors and windows without a balcony, a danger warning area must be set up on the ground below to prevent people from approaching.
- Check the safety rope for any damage and ensure the knot is secure before using.
- Fasten the safety rope to a stable indoor object to prevent the robot from falling.
3.4 Adding Water to the Tank
- Open the silicone cover on the water tank.
- Add clean, impurity-free water. Do not add any other cleaning agents to the water tank.
- Fill the water tank to about 80% capacity to maintain stable air pressure.
3.5 Attaching the Machine to the Glass
- Press and hold the power key for 2 seconds to turn on the robot. Confirm that the fan rotates.
- Place the machine on the glass, maintaining a certain distance from the window frame.
- Ensure the machine is securely attached to the glass before releasing your hands.
4. Operating Instructions
4.1 Cleaning Modes
The robot offers three intelligent path planning modes:
- Up to Down: Cleans from the top of the window downwards.
- Left to Down: Cleans from the left side of the window downwards.
- Right to Down: Cleans from the right side of the window downwards.

4.2 Dry Wipe
For the first cleaning pass, especially on dirty glass, perform a dry wipe without spraying water to remove loose sand and dirt. Spraying water or detergent initially can mix with sand and create mud, reducing cleaning effectiveness. Dry wiping is most effective in sunny or low-humidity weather.
4.3 Wet Wipe (Water Spray Function)
The robot has a single water spray hole. When the robot is cleaning, it sprays water forward.
- Automatic Water Spray: In auto cleaning mode, press the "AU" button on the remote control. The robot will beep twice, indicating automatic water spray is on, and water will be sprayed intermittently. Press "AU" again to turn off.
- Manual Water Spray: In auto cleaning mode, press the water spray button on the remote control once to spray water once.


4.4 Remote Control
The remote control uses 2.4G/infrared technology. It allows you to select cleaning modes, manually control movement, and activate water spray.

Remote Control Battery: Use No., AAA/RL batteries of the specified type. Do not mix old and new batteries or different types. Install by aligning the negative pole with the spring first, then pressing down.
4.5 Power Failure Protection (Backup Battery)
In case of power failure, the built-in backup battery activates, providing power for up to 20 minutes (when fully charged). The machine will stay in place, emit a warning sound, and the red/blue lights will flash alternately. Retrieve the machine as soon as possible to prevent falling. Gently pull the safety rope, keeping it close to the glass, to retrieve the device.

5. Maintenance
5.1 After Cleaning
- Hold the window cleaner with one hand and press the power button for 2 seconds with the other hand to turn off the power.
- Remove the window cleaning robot from the window.
- Untie the safety rope and store the machine and its related accessories in a dry and ventilated environment for future use.
5.2 Cleaning Cloths
- The microfiber cleaning cloths are easily removable and replaceable.
- If round wheel marks remain on the glass surface after cleaning, the cleaning cloth is likely too dirty and should be replaced with a clean one.
- If the machine does not run smoothly, replace the cleaning cloth.

5.3 Water Spray Nozzle and Tank
- If the machine does not spray water, clean the ultrasonic nozzle with a clean, soft cloth.
- Check the water tank to ensure it contains water and that the cleaning solution added is clean and pure.
5.4 Cleaning Wheel Screw
- If the machine does not run smoothly, check if the screw of the cleaning wheel is loose. Tighten it, but do not overtighten, as this may affect the glass glue thickness or the performance of beveled window frames.
6. Troubleshooting
6.1 Machine Runs Slowly or Fails on First Use
- **Cause:** Cleaning cloth is too dirty, or glass surface is very dirty.
- **Solution:** Clean and dry the supplied cleaning cloth before use. Spray a little water or glass cleaner evenly on the cleaning cloth or glass surface, then wring out the cloth before placing it in the cleaning ring.
6.2 Machine Tests Itself, Makes Warning Sound, or Has Too Much/Little Friction
- **Cause:** Dirty cleaning cloth, low friction coefficient of glass stickers/fog stickers, very clean/slippery glass, or low humidity (air-conditioned room).
- **Solution:** Replace dirty cloth. Ensure the surface is suitable for the robot. If glass is too clean, it might be too slippery. Adjust humidity if possible.
6.3 Machine Cannot Detect Upper Edge of Window
- **Cause:** Sliding of the upper edge of the window.
- **Solution:** Press the appropriate key on the remote to switch to another auto clean mode.
6.4 Machine Cannot Wipe Upper Left Side of Glass
- **Cause:** Slippery glass or cleaning cloth, wider wiped glass area, or slight top line slide.
- **Solution:** Use the remote control's manual window cleaning mode to target the unwiped area.
6.5 Machine Finishes Cleaning Early Without Completing All Windows
- **Cause:** Robot prematurely detects completion.
- **Solution:** Press the appropriate button or select an auto window mode to continue the unfinished part.
6.6 Slipping and Not Climbing
- **Cause:** Friction is too small (low friction stickers, thermal insulation, or fog stickers), cleaning cloth is too wet, very clean/slippery glass, or low humidity. Incorrect starting position.
- **Solution:** Ensure suitable surface. Use a dry or slightly damp cloth. Start the machine at a distance from the window frame to avoid incorrect judgment.
6.7 Round Wheel Marks on Glass Surface
- **Cause:** Cleaning cloth is too dirty.
- **Solution:** Replace with a clean cloth and wipe again.
6.8 Machine Does Not Run Smoothly
- **Cause:** Dirty cleaning cloth, different types of glass areas (e.g., glass area, sticker area), or loose cleaning wheel screw.
- **Solution:** Replace dirty cloth. Use the robot on a single type of area. Check and tighten the cleaning wheel screw.
6.9 Warning Sound and Red Light Flashing (Power Failure)
- **Cause:** Power failure.
- **Solution:** Gently pull the safety rope back to the machine (keeping it close to the glass). Turn off the machine. Check the power wire for poor contact or breakage.
6.10 Machine Stops Due to Unknown Obstacles (Red Light Flashes, No Warning Sound)
- **Cause:** Obstacle on the window or air leak.
- **Solution:** Use the remote control to move the machine to a safe position. Remove any obstacles. Check for air leaks.
6.11 Arc Marks on Polished Glass at Night
- **Cause:** Initial dirt/sand on glass, or wet cleaning cloth.
- **Solution:** For the first time, turn off water spray and use a clean cloth to remove sand. For the second wipe, clean and replace the cloth, turn on water spray, or keep the upper cleaning wheel clean and dry, and spray a little detergent or alcohol on the lower cleaning wheel (1 or 2 sprays). This helps eliminate arc traces.
6.12 Machine Does Not Stop Automatically After Cleaning All Windows
- **Cause:** Robot does not detect completion.
- **Solution:** Press the stop key on the remote control to stop the operation.
6.13 Machine Will Not Spray Water
- **Cause:** Water spray function switch is off, clogged ultrasonic nozzle, or empty/impure water tank.
- **Solution:** Confirm the water spray function switch is on. Clean the ultrasonic nozzle with a soft cloth. Check the water tank for water and ensure the added cleaning solution is clean and pure.
7. Specifications
| Attribute | Specification |
|---|---|
| Input Voltage | AC100~240V 50Hz~60Hz |
| Rated Power | 72W |
| Battery Capacity | 650mAh |
| External Dimensions | 295*145*95mm |
| Suction Power | 2800Pa |
| Net Weight | 1030g |
| Power Failure Protection Time | 20min |
| Control Method | Remote control |
| Noise Level | 65-70dB |
| Border Detection | Automatic |
| Fall Arrest Control | Power failure protection (backup battery) safety rope |
| Cleaning Mode | Intelligent path planning modes |
| Water Tank Capacity | 35ml |
| Water Spraying Method | Manual / Auto |
| Motor Type | Brushed motor |
| Certification | ROHS, CE, FCC, UL, CCC |



8. Warranty and Support
The DIVEDEER YTK334 Window Cleaning Robot comes with a 1-year warranty. In case of any damage, parts will be sent for free, along with an installation video for self-repair. Damages caused by artificial means are not covered under the free warranty.
For assistance, repairs, or battery replacement, please contact your local customer service or distributor. The built-in battery should only be replaced by the manufacturer or a designated service center to avoid potential hazards.
9. User Tips
- **Initial Startup:** After turning on the robot, wait 20 seconds until the blue light stops flashing before starting work. This allows the robot to detect the glass plane accurately.
- **Safety First:** Always bind the safety rope when using the robot to prevent it from falling from high altitudes.
- **Enhanced Cleaning:** For better cleaning results, spray a small amount of water on the edge of the microfiber mop pads before operation.
- **Corner Cleaning:** While the robot is designed for efficient cleaning, it may not reach extremely tight corners perfectly due to its shape and movement patterns. For detailed corner cleaning, manual touch-up might be necessary.
- **Support:** If you have any questions or need operational guidance, contact customer support. They can provide answers and operation videos.