Introduction
This manual provides detailed instructions for the safe and efficient operation of your Irradio UV 88 Multi-Band Walkie Talkie. Please read this manual thoroughly before using the device to ensure proper functionality and to prevent damage or injury.
The Irradio UV 88 is a versatile multi-band walkie talkie featuring FM, Shortwave (SW), Medium Wave (MW), and Long Wave (LW) reception, along with transmit capabilities in VHF/UHF bands. It includes 1024 channels, USB-C charging, and NOAA weather forecast channels (US only).

Safety Precautions
Please observe the following precautions when using this product to avoid fire, personal injury, damage to equipment or other accidents:
- Do not use the equipment in inflammable and explosive environments (such as gas, dust, smoke, etc.). Turn off the equipment when refueling or parking at a gas station.
- Do not place the equipment in dusty, wet, or splashed places or on uneven surfaces.
- Please use this equipment away from interference sources (such as TV, computer, distribution cabinet, etc.).
- Do not transmit while charging.
- Do not use the radio while driving.
- Do not expose the device to direct sunlight for a long time or place it near a heating device.
- If the equipment emits abnormal odor, it must be turned off immediately. After ensuring safety, it should be sent to the nearest maintenance site for inspection.
- Do not modify or adjust this equipment for any reason.
- Please obey all local laws and regulations.
Disclaimer: The customer shall bear all responsibility for equipment failure or accident caused by the customer's violation of the above precautions. The company shall not be responsible for it.
Package Contents
Verify that all items are present in your package:
- 1 x Irradio UV 88 Radio
- 1 x Antenna
- 1 x Battery
- 1 x Charger
- 1 x Belt Clip
- 1 x Type-C cable
- 1 x Adaptor

Setup
Familiarizing with Your Radio
Before initial use, take a moment to identify the main components of your Irradio UV 88 radio:

- Antenna: For signal transmission and reception. The radio supports Short/Medium/Long Wave FM Antenna.
- ON/OFF/Volume Knob: Turns the radio on/off and adjusts the volume.
- Speaker/MIC: For audio output and input.
- Display Screen: Shows frequency, channel, mode, and other operational information.
- Keypad: For inputting frequencies, channel numbers, and accessing functions.
- PTT (Push-to-Talk) Button: Press and hold to transmit.
- Side-key 1 & 2: Programmable function keys.
- Battery: Provides power to the unit.
- Earpiece/Programmable Jack: Connect external audio accessories or programming cable.
- Type-C Charging Port: For charging the radio.
Initial Charging
Before first use, fully charge the radio's battery using the provided Type-C cable and adaptor. The radio can be charged via a Type-C cable or a base charger.

Operating Instructions
Keypad Functions
The keypad provides access to various functions and inputs. Refer to the table below for a detailed overview:

Keypad Function Highlights:
- PTT: Transmit or Exit.
- Alarm Key: Definable long press and short press functions.
- Side Key 1 & 2: Definable long press and short press functions.
- 0-9 Keys: Input numbers, access definable functions (long press), or input English/Chinese characters.
- *: Long press to lock keypad, short press to switch channel/frequency/alias.
- #: Switch working mode (VFO/channel/zone), activate inputting status, switch input methods.
LCD Display Indicators
The LCD display provides critical information about the radio's status and operation:
- VFO MODE /CH MODE /ZONE-XXX Mode (XXX indicates current working zone)
- Main frequency icon
- Channel number
- AM or FM Analog RX modulation
- CTC analog channel with sub-tones/DCS analog channel with digital sub-tones/ENC analog channel with encrypted sub-tone/MUT analog channel with decoded sub-tone
- H/L: High/Low Power
- W/N: Wide/Narrow Band
- Sub-display information
- Main Display information
- System Time
- Battery Power
- Beep
- Dual standby
- Scanning
- R-Talk around /T-Freq Inverse
- Keypad Lock
- Signal Icon
Basic Settings
Access the main menu to configure various radio settings. Press the menu button (usually the 'O' key) to enter the menu interface.

Some key settings include:
- Name/Callsign: Edit radio name or callsign.
- Voice Prompt: Turn on/off voice prompts.
- Lock Timer: Sets the time for keypad auto-lock.
- Brightness/Backlight: Adjust display brightness and backlight behavior.
- Dual Standby: Select dual or single standby.
- Freq Step: Set frequency or scan step.
- Scan Mode: Configure scanning behavior (TO, CO, SE).
Key Define
Customize the functions of the side keys and numeric keys for quick access to frequently used features.

Analog Set
Configure analog communication parameters such as squelch level, TX tones, and microphone/speaker gain.

Digital Set
Adjust digital communication settings, including personal ID, call tones, group/single call holding times, and encryption.

Channel Set
Manage channel-specific settings like CTC/DCS tones, TX frequency, DCX encryption, band width, and offset frequencies.

Zone Set, Radio, and Time Message
Organize your channels into zones, configure FM radio settings, and manage time-related functions.

Detailed Function Description
This section provides in-depth explanations for various radio functions and their usage.
1. Input Frequency
- Switch working mode to VFO frequency mode by pressing the # key.
- Input frequency via number keys (6 or 8 digits). Set inputting digits in Menu 【Radio Set】 -> 【6 or 8 Bits Input】.
2. Input Repeater Frequency
Method 1:
- Enter Menu 【Channel Set】 -> 【Offset Freq】 to input frequency difference via number keypads.
- Enter Menu 【Channel Set】 -> 【Offset DIR】 to set frequency upwards and downwards.
Method 2: Long press # button to enter 【TX Frequency】 and input TX frequency, press O to confirm then go back to previous menu. Press * to set CTCSS/DCS.
3. Transmitting
- Press PTT to transmit at current frequency; the indicator lights up red.
- Press Menu 【Basic Set】 -> 【Main PTT TX】 and set up as 【Area A】 to transmit at A frequency always. If set up as 【Main Area】, it transmits at main frequency all the time.
- Turn on 【Key Define】 -> 【Slaver PTT】; the shortcut function of side-key 1 is invalid, press side-key 1 to transmit at B frequency.
4. Receiving
The indicator lights up green while receiving. If there is no RX sub-tone, or the sub-tone matches, the speaker works.
5. DTMF (Dual-Tone Multi-Frequency)
5.1 DTMF Inputting and Sending
- Press * to enter DTMF inputting interface while under standby status.
- Press numeric keys to input DTMF codes, press * to delete the last code (short press side-key 1 to delete when it doesn't use as second PTT).
- Press PTT to call; the radio sends DTMF code to receiver after appointed delay time.
5.2 DTMF Decoding
While the radio is in receiving status, the display shows the sender's DTMF code if DTMF decoding is turned on.
5.3 Sending DTMF in Analog Transmitting Status
Press keypads to send relative DTMF code while under analog transmitting status.
5.4 DTMF Remote Monitor
- Open the DTMF Control setting in (Analog Set).
- Other radios send DTMF code with the same monitor code to this radio.
- After decoding successfully, the radio transmits for 60 seconds automatically to enable remote monitor.
5.5 DTMF Stun/Kill/Activate
- Set up a DTMF code for Stun/Kill/Activate, and turn on 【DTMF Control】.
- Other radios will perform Stun/Kill/Activate to this radio when they send relative DTMF code.
The radio cannot be used until it receives an activate code if it is in Kill status. In Stun status, the radio can receive but cannot input anything via keypad or transmit. Note: An Activate code must be set up once Stun/Kill code is set up, otherwise the device cannot be activated.
6. Text Input
- Press # to switch inputting methods, press * to delete inputting when under text input status.
- Press number keys 【123】 to input numbers.
6.3 English Letters Inputting 【AB】 【abc】
- Number 2-9 can input relative English letters, press Number 0 to input space, Number 1 to input English symbols.
- Press the same button to switch to different letters.
7. Function of Definable keys
- [Monitor]: Enter into receiving and playing status once triggered.
- [H/L Power]: Switch high/low power of current channel.
- [Dual Standby]: Turn on/off dual standby. Power saving mode is invalid once dual standby turns on.
- [TX Priority]: Switch priority RX to [Edit] or [Busy]. If set to Busy status, the main frequency shifts to the calling frequency automatically when the calling ends.
- [Scanning]: Enter scanning status, press arbitrary keys to exit.
- [Backlight On-off]: Turn on/off backlight.
- [Roger Beep]: Switch RX end tone types.
- [FM Radio]: Press defined side button to enter FM status, press PTT to exit. Use * key to switch cursor position.
For more detailed function descriptions, please refer to the original user manual PDF: Iradio UV 88 User Manual (PDF).
Specifications
The Irradio UV 88 is designed with robust features for reliable communication. Below are the detailed technical specifications:

| Feature | Specification |
|---|---|
| Brand Name | RONGYIN (Iradio) |
| Model Number | Iradio UV 88 |
| Walkie Talkie Type | Portable |
| Output Power (W) | 3W-5W |
| Maximum Range | 5km-10km |
| Frequency Range | Multi Band |
| FM Radio | 64-108MHz |
| Shortwave (SW) | 2.3-30MHz |
| Medium Wave (MW) | 520-1710KHz |
| Long Wave (LW) | 153-279KHz |
| Receive (RX) | 18-520MHz (AM or FM, covering CB band) |
| Transmit (TX) | 136-174MHz, 400-480MHz |
| Storage Channel | 1024 Channels + 2 VFO channels |
| Battery Capacity | 2000mAh |
| Battery Included | Yes |
| Charging Method | TYPE-C cable charger / base charger |
| Waterproof / Water-Resistant | IP67 |
| Material | Plastic |
| Dimensions (without antenna) | 137*60*36mm |
| Weight (without antenna) | Approx. 255g |
| Certification | CE, Dot, EPA, FCC, GMP, RoHS, TGA, UL, KC, pse, weee |
Maintenance
To ensure the longevity and optimal performance of your Irradio UV 88 Walkie Talkie, follow these maintenance guidelines:
- Cleaning: Use a soft, damp cloth to clean the radio's exterior. Do not use harsh chemicals or abrasive cleaners.
- Storage: Store the radio in a cool, dry place away from direct sunlight and extreme temperatures.
- Battery Care: Avoid fully discharging the battery frequently. Charge the battery regularly, even if the radio is not in use, to maintain battery health.
- Antenna: Ensure the antenna is securely attached. Do not bend or force the antenna, as this can damage the connector.
- Inspection: Periodically check the radio for any signs of damage or wear.
Troubleshooting
If you encounter issues with your Irradio UV 88, refer to the following common problems and solutions:
- Radio not powering on:
- Ensure the battery is fully charged.
- Check if the battery is properly installed.
- Verify the ON/OFF/Volume knob is turned to the 'ON' position.
- No signal reception:
- Check antenna connection.
- Ensure you are within range of a transmitting station.
- Adjust the squelch level (SQ level in Analog Set menu).
- Verify the frequency and channel settings are correct.
- Cannot transmit:
- Ensure the PTT button is fully pressed.
- Check battery level; low battery might prevent transmission.
- Verify TX frequency and power settings.
- If the radio is in "Stun" status (DTMF Stun/Kill/Activate), it cannot transmit. An "Activate" code must be received to restore full functionality.
- Abnormal odor from equipment:
- Immediately turn off the radio.
- Disconnect the battery.
- Do not attempt to use or repair. Send to the nearest maintenance site for inspection.
- Keypad unresponsive/locked:
- Check if the keypad lock is active (long press * to unlock).
- If the radio is in "Kill" status (DTMF Stun/Kill/Activate), the keypad will be unresponsive. An "Activate" code must be received.
For complex issues not covered here, please consult the full user manual PDF or contact customer support.
User Tips
- SSB Reception: Users have reported excellent SSB reception, particularly around 7.091 MHz. Experiment with fine-tuning for optimal clarity.
- Software and Manual: An English manual and software are available for download. If you need them, contact the seller or check the provided link in the product description for software updates and detailed guides.
- GPS Version: Note that a GPS version of this radio may also be available. Ensure you have the correct model if GPS functionality is desired.
Warranty and Support
We promise to carefully 100% INSPECT quality, specification and quantity of the items before delivery.
We offer ONE YEAR WARRANTY for the radio body, and THREE MONTHS for the battery, charger, and other accessories.
For any support inquiries or warranty claims, please contact the seller directly. Please provide your correct shipping address if sending any parcel for warranty repair or exchange.
Additional Resources
A comprehensive user manual in PDF format is available for download. This document contains detailed instructions and diagrams that may not be fully replicated in this HTML guide.
Download User Manual (PDF): Iradio UV 88 User Manual (PDF)