1. Introduction
This manual provides essential information for the safe and effective operation, setup, and maintenance of your JASIC ZX7-315DE Portable Manual Welding Machine. Please read this manual thoroughly before using the equipment and keep it for future reference. The ZX7-315DE is an industrial-grade, dual-voltage ARC manual welding machine designed for welding steel, stainless steel, and mild steel.
2. Safety Information
WARNING: Welding can be dangerous. Always follow safety precautions to prevent injury or death.
- Always wear appropriate personal protective equipment (PPE), including a welding helmet with proper shade, flame-resistant clothing, welding gloves, and safety shoes.
- Ensure adequate ventilation in the work area to avoid inhaling welding fumes.
- Protect bystanders from arc rays and hot metal.
- Do not operate the machine in damp or wet conditions.
- Ensure the machine is properly grounded.
- Disconnect power before performing any maintenance or service.
- Keep children and unauthorized personnel away from the welding area.
- Always use the correct input voltage (AC 220V or AC 380V) as indicated on the machine and ensure the power supply is stable.
3. Product Overview
The JASIC ZX7-315DE is a compact and powerful manual ARC welding machine. Familiarize yourself with its components:
3.1 Front Panel

- Digital Display (A): Shows the welding current.
- AC 220V/AC 380V Indicators: Lights indicating the active input voltage.
- Current Adjustment Knob: Used to set the main welding current.
- Thrust Current Adjustment Knob: Used to adjust the arc force (thrust current) for better arc stability and penetration.
- Welding Cable Connectors (+/-): Quick-connect terminals for welding cables.
3.2 Rear Panel

- Power Input (AC 220V/380V): Connection point for the main power cable.
- ON/OFF Circuit Breaker: Main power switch and overload protection.
- Cooling Fan: Ensures proper cooling during operation.
3.3 Included Accessories

- 2 x 35-50 Quick Plugs (for welding cables)
- 1 x Hex Key (for securing connections)
4. Setup Instructions
- Placement: Place the welding machine on a stable, level surface in a well-ventilated area, away from flammable materials.
- Power Connection:
- Ensure the ON/OFF circuit breaker on the rear panel is in the "OFF" position.
- Connect the power cable to the AC 220V or AC 380V input on the rear panel. Verify that the power source matches the machine's requirements.
- Plug the power cable into a suitable and properly grounded electrical outlet.
- Welding Cable Connection:
- Connect the electrode holder cable to the positive (+) quick-connect terminal on the front panel.
- Connect the earth clamp cable to the negative (-) quick-connect terminal on the front panel.
- Ensure all connections are secure using the provided hex key if necessary.
- Attach the earth clamp securely to the workpiece, ensuring good electrical contact.
5. Operating Instructions
- Power On: Flip the ON/OFF circuit breaker on the rear panel to the "ON" position. The digital display on the front panel will light up, and the corresponding voltage indicator (AC 220V or AC 380V) will illuminate.
- Select Welding Current: Rotate the "Current Adjustment" knob on the front panel to set the desired welding current. The digital display will show the selected amperage. Refer to your electrode manufacturer's recommendations for appropriate current settings.
- Adjust Thrust Current: Rotate the "Thrust Current Adjustment" knob to fine-tune the arc force. Higher thrust current can help prevent the electrode from sticking and improve penetration, especially with difficult-to-weld materials or in specific positions.
- Begin Welding:
- Strike an arc by lightly touching the electrode to the workpiece and quickly lifting it slightly to establish the arc.
- Maintain a consistent arc length and travel speed for optimal weld quality.
- Always ensure proper ventilation and wear full PPE during welding.
- Power Off: After welding, turn the ON/OFF circuit breaker to the "OFF" position.
6. Maintenance
Regular maintenance ensures the longevity and safe operation of your welding machine.
- Cleaning: Periodically clean the machine's exterior with a dry, soft cloth. Ensure cooling vents are free from dust and debris to prevent overheating.
- Cable Inspection: Regularly inspect welding cables, electrode holder, and earth clamp for damage, fraying, or loose connections. Replace damaged components immediately.
- Storage: Store the machine in a dry, clean environment when not in use.
- Internal Cleaning: For internal cleaning, it is recommended to have a qualified technician perform the service to avoid damaging sensitive electronic components.
7. Troubleshooting
Before contacting support, check the following common issues:
| Problem | Possible Cause | Solution |
|---|---|---|
| Machine does not power on. | No power supply; circuit breaker tripped; faulty power cable. | Check power outlet; reset circuit breaker; inspect power cable. |
| No welding output. | Loose welding cable connections; incorrect current setting; faulty electrode. | Secure cable connections; adjust current; replace electrode. |
| Arc is unstable or difficult to strike. | Poor earth clamp connection; incorrect current/thrust setting; damp electrode. | Clean and secure earth clamp; adjust current/thrust; use dry electrodes. |
| Overheating indicator on. | Exceeded duty cycle; blocked cooling vents; high ambient temperature. | Allow machine to cool down; clear vents; operate in cooler environment. |
8. Specifications
Technical specifications for the JASIC ZX7-315DE welding machine:

| Feature | Specification (ZX7-315DE) |
|---|---|
| Product Name | Welding Machine ARC Manual Welding Machine |
| Model Number | ZX7-315DE |
| Input Voltage (V) | Single phase AC 220V±15% / 380V±15% |
| Rated Input Capacity (kVA) | 7.1 (220V) / 9.4 (380V) |
| Power Factor | 0.7 |
| Rated No-Load Voltage (V) | 65 (220V) / 59 (380V) |
| Welding Current (A) | 20-160 (220V) / 20-200 (380V) |
| Thrust Current (A) | 0-100 |
| Rated Load Duration Rate @ 40℃ | 25% |
| Efficiency | 85% |
| Protection Level | IP21S |
| Insulation Level | H |
| Weight (kg) | 5.4 |
| Dimensions (L x W x H) | 356 x 158 x 309 mm |
| Welding Process | ARC Manual Welding (MMA) |
| For Material Type | Steel, Stainless Steel, Mild Steel |
| Configuration | 2 quick plugs |
9. User Tips
- For optimal performance, ensure your power supply is stable and matches the machine's voltage requirements.
- Experiment with the thrust current knob to find the best arc stability for different electrodes and welding positions.
- Always keep your work area clean and free of clutter to prevent accidents.
10. Warranty and Support
The JASIC ZX7-315DE welding machine comes with a 1-year warranty from the date of purchase.
For any questions regarding the product, operation, or troubleshooting that cannot be resolved using this manual, please contact the seller or authorized service center for assistance. Provide your product model number (ZX7-315DE) and purchase details when seeking support.