1. Introduction
Thank you for choosing the ANDELI CUT-55Y Plasma Cutting Machine. This high-performance inverter plasma cutter is designed for efficient and precise metal cutting, featuring both High-Frequency (HF) and Non-High-Frequency (Non-HF) cutting modes, a built-in air pump, and an intuitive LED screen display. This manual provides essential information for safe operation, setup, maintenance, and troubleshooting to ensure optimal performance and longevity of your machine.

The ANDELI CUT-55Y Plasma Cutting Machine, a versatile tool for metal fabrication.
2. Safety Information
Always prioritize safety when operating welding and cutting equipment. Failure to follow safety guidelines can result in serious injury or death.
- Electrical Safety: Ensure the machine is properly grounded. Do not operate in wet conditions. Always disconnect power before performing maintenance or changing accessories.
- Fume Hazards: Welding and cutting fumes can be hazardous. Work in a well-ventilated area or use a fume extractor.
- Arc Rays: Arc rays can burn eyes and skin. Wear appropriate welding helmet with proper shade, safety glasses, and protective clothing.
- Fire and Explosion: Keep flammable materials away from the work area. Hot metal and sparks can cause fires.
- Compressed Air: The built-in air compressor generates high pressure. Do not direct air at yourself or others. Ensure air lines are secure.
- Personal Protective Equipment (PPE): Always wear a welding helmet, safety glasses, gloves, long-sleeved shirts, and sturdy footwear.
3. Package Contents
Verify that all items are present in your package:
- ANDELI CUT-55Y Plasma Cutting Machine
- FPT-40 Plasma Cutting Torch (4M cable)
- MMA Holder (for Stick Welding)
- Ground Clamp
- Consumables: Nozzles and Electrodes

The CUT-55Y machine and its included accessories: FPT-40 torch, MMA holder, nozzles, and electrodes.
4. Specifications
The following table details the technical specifications of the ANDELI CUT-55Y Plasma Cutting Machine:

Detailed technical specifications for the CUT-55Y model.
| Parameter | CUT | MMA |
|---|---|---|
| Input Voltage (V) | AC220±15% | |
| Rated Input Capacity (KVA) | 7.0 | 6.4 |
| Rate Input Current (A) | 32 | 29 |
| No-load Voltage (V) | 310 | 68 |
| Current Range (A) | 20-40 | 30-140 |
| Rate Output Voltage (V) | 88/96 | 21.2/25.6 |
| Duty Cycle (40°C, 10min) | 60% 30A, 100% 23A | 25% 140A, 60% 90A, 100% 70A |
| Efficiency (%) | 79 | 80 |
| Power Factor | 0.76 | 0.7 |
| Insulation Class | H | |
| Protection Class | IP21S | |
| Machine Dimensions (mm) | 484x177x292 | |
| Weight (kg) | 13.5KG±0.2KG | |
Cutting Thickness Capabilities:
- HF Mode (110V): Max Cutting Thickness 15mm, Quality Cutting Thickness 10mm
- HF Mode (220V): Max Cutting Thickness 20mm, Quality Cutting Thickness 15mm
- Non-HF Mode (110V): Max Cutting Thickness 17mm, Quality Cutting Thickness 12mm
- Non-HF Mode (220V): Max Cutting Thickness 25mm, Quality Cutting Thickness 20mm

Physical dimensions of the CUT-55Y unit.
5. Setup Instructions
- Unpacking: Carefully remove the machine and all accessories from the packaging. Inspect for any shipping damage.
- Placement: Place the machine on a stable, level surface in a well-ventilated area, away from moisture and direct sunlight. Ensure adequate clearance for cooling air circulation.
- Power Connection: Connect the machine to a suitable AC220V (or 110V if applicable to your model variant) power supply. Ensure the power outlet is properly grounded and can handle the rated input current.
- Ground Clamp Connection: Attach the ground clamp cable to the designated terminal on the machine. Securely attach the ground clamp to the workpiece or work table, ensuring good electrical contact.
- Torch Connection:
- For HF (High-Frequency) cutting, connect the HF torch to the corresponding port.
- For Non-HF (Low-Frequency) cutting, connect the Non-HF torch to its designated port.
Note: The machine must be switched to the interface corresponding to the cutting torch being used.

Connection points for HF and LF cutting torches. Ensure the correct torch is connected to the appropriate port.
- Air Supply: The CUT-55Y features a built-in air compressor, eliminating the need for an external air source for most operations. If cutting thicker materials or requiring higher performance, an external air compressor can be connected to supplement the internal one.
6. Operating Instructions
The LED large screen display makes functions visible and adjustable, simplifying operation for beginners.

The control panel with LED display, showing various buttons and the adjustment knob.
- Power On: Turn on the main power switch. The LED screen will illuminate.
- Mode Selection: Use the 'Function Selection Button' (5) to choose between HF CUT, LF CUT, or MMA mode.
- Parameter Adjustment: Use the 'Knob Gear' (7) to adjust parameters such as Cutting Current, Gas Time, Hot Start Current, or ARC FORCE Current, depending on the selected mode.
- GAS Select Button (1): For internal gas/external gas/VRD in MMA mode.
- Select Button (2): For Grid/2T/4T in CUT mode.
- GAS Time Select Button (3): Adjusts CUT mode Pre-flow time (1-10S) and Post-flow time (5-15S).
- Gas Check (4): Use this function to test the gas flow before cutting.
- MMA Mode Function Button (6): In MMA mode, this button allows adjustment of Hot Start (0-10%), Arc Force (0-10%), and Arc Time.
- Cutting Operation:
- Ensure proper PPE is worn.
- Position the torch correctly over the workpiece.
- Initiate the arc according to the selected cutting mode (HF or Non-HF).
- Maintain a steady travel speed for a clean cut.

Illustration of HF and Non-HF cutting modes and their respective maximum cutting thicknesses.
- MMA Welding Operation:
- Select MMA mode.
- Connect the MMA holder and ground clamp.
- Adjust current, Hot Start, and Arc Force as needed for your electrode and material.
- Begin welding, maintaining a consistent arc length.

The machine supports MMA welding with VRD for higher efficiency.
7. Maintenance
Regular maintenance ensures the longevity and optimal performance of your plasma cutter.
- Nozzle and Electrode Replacement: The machine features a unique arc feedback technology that intelligently detects nozzle wear and prompts for replacement when flashing. Replace worn nozzles and electrodes promptly to maintain cut quality and torch life.
- Cleaning: Regularly clean the machine's exterior with a dry cloth. Ensure cooling vents are free from dust and debris.
- Air Filter: Periodically check and clean or replace the air filter for the built-in compressor to ensure clean air supply and efficient operation.
- Cable Inspection: Inspect all cables (power, torch, ground) for damage before each use. Replace any damaged cables immediately.
- Storage: Store the machine in a dry, clean environment when not in use.

The arc feedback system indicates when to change the nozzle, prolonging torch service life.
8. Troubleshooting
This section addresses common issues you might encounter.
| Problem | Possible Cause | Solution |
|---|---|---|
| Machine does not power on | No power supply; Main switch off; Faulty power cable | Check power connection; Turn on main switch; Inspect/replace cable |
| No arc initiation | Poor ground connection; Worn consumables (nozzle/electrode); Incorrect air pressure; Incorrect mode selection | Ensure good ground contact; Replace consumables; Check air pressure; Verify correct mode (CUT/MMA, HF/Non-HF) |
| Poor cut quality / Inconsistent arc | Worn consumables; Incorrect cutting speed/height; Insufficient air pressure; Material too thick | Replace consumables; Adjust cutting parameters; Check air pressure; Ensure material thickness is within machine capacity |
| Overheating / Thermal overload | Exceeding duty cycle; Blocked ventilation; High ambient temperature | Allow machine to cool down; Ensure clear ventilation; Operate within duty cycle limits |
| Air flow issues | Blocked air filter; Internal compressor issue; External air supply problem (if used) | Clean/replace air filter; Consult service for internal compressor; Check external air supply connections |
9. User Tips
- Optimize for Thickness: For thinner materials, the built-in air compressor is usually sufficient. For thicker cuts (e.g., above 15mm), consider connecting an external air compressor to achieve the maximum cutting thickness and best quality.
- Monitor Consumables: Pay attention to the arc feedback indicator for nozzle wear. Replacing consumables proactively will prevent poor cuts and extend the life of your torch.
- Material Versatility: This machine is suitable for cutting a wide range of materials including iron, stainless steel, aluminum, and copper. Adjust settings according to the specific material and its thickness.
- Practice Makes Perfect: Plasma cutting requires a steady hand and consistent travel speed. Practice on scrap material to find the optimal settings and technique for different cuts.

The CUT-55Y is capable of cutting various metals including iron, stainless steel, aluminum, and copper.

An external air compressor can be added to cut thicker materials more effectively.
10. Warranty and Support
The ANDELI CUT-55Y Plasma Cutting Machine comes with a 2-year warranty from the date of purchase, covering manufacturing defects. Please retain your proof of purchase for warranty claims.
For technical support, service, or warranty inquiries, please contact your retailer or the manufacturer's customer service department. Provide your model number (CUT-55Y) and a detailed description of the issue to expedite assistance.