YJCAL P421 P422 P423 P424 P425

Contents

YJCAL Universal Compact Wire Connector Instruction Manual

Models: P421, P422, P423, P424, P425

1. Important Safety Instructions

WARNING

  • Please ensure the power supply is completely disconnected before wiring. Do not operate while live to prevent the risk of electric shock.
  • Only applicable to circuits within the rated voltage and current range. Refer to the product casing for specific parameters. Overloading may cause fires or equipment damage.
  • Avoid installing this product in damp, dusty, or flammable/explosive environments. It is only suitable for indoor use in dry, non-corrosive gas conditions.
  • The stripping length of the wire must strictly match the terminal requirements, as being too long or too short may result in poor contact or arcing.
  • Do not disassemble or modify this product, non-professional operation may damage the insulation performance and cause safety hazards.
  • Keep out of reach of children.

For more detailed safety information, please refer to the official user manual (PDF) available at User Manual (PDF).

2. Product Overview

The YJCAL Universal Compact Wire Connectors are designed for quick and secure electrical connections in various applications, including LED lighting. They feature a compact design and are available in multiple configurations (1-in-1-out, 2-in-2-out, 3-in-3-out, 4-in-4-out, 5-in-5-out) to suit different wiring needs. These connectors can be infinitely spliced for extended connections and can be mounted on guide rails for organized installations.

Diagram showing how multiple wire connectors can be spliced together to extend connections.

Figure 1: Illustration of wire connectors being spliced together.

3. Setup and Operation

Follow these steps to properly connect wires using the YJCAL Universal Compact Wire Connectors:

  1. **Prepare the Wire**: Ensure the power supply is completely disconnected. Strip the insulation from the end of the wire. The recommended stripping length is 10-12mm (0.39-0.47 inches).
  2. **Open the Connector Lever**: Open the orange operating lever of the wire connector to a 90-degree angle.
  3. **Insert the Wire**: Insert the stripped end of the wire completely into the connector's opening.
  4. **Close the Lever**: Push the orange operating lever down firmly until it is flush with the connector body. This secures the wire connection.

Video 1: Demonstration of wire connector assembly and rail mounting.

3.1. Splicing Connectors

Multiple connectors can be spliced together to create longer or more complex wiring configurations. Simply align the side grooves of one connector with the protrusions of another and slide them together until they click securely.

Close-up of two 2-pin gray wire connectors spliced together.

Figure 2: Two 2-pin connectors spliced together.

3.2. Guide Rail Mounting

For organized installations, the connectors can be mounted onto a guide rail using compatible rail bases (models QHJ-DK42 or QHJ-DZ43). Attach the rail base to the connector, then snap the assembly onto the guide rail.

Wire connectors mounted on a guide rail for organized electrical installations.

Figure 3: Wire connectors installed on a guide rail.

4. Maintenance

To ensure optimal performance and longevity of your wire connectors:

  • Regularly inspect connections for any signs of loosening, corrosion, or damage.
  • Keep the connectors clean and free from dust and debris.
  • Ensure the operating levers are fully closed to maintain a secure connection.
  • Avoid exposing connectors to excessive moisture or extreme temperatures.

5. Troubleshooting

If you encounter issues with your wire connectors, consider the following:

  • **Poor Contact or Arcing**: This can often be caused by incorrect wire stripping length. Ensure the wire is stripped to 10-12mm as specified. Re-strip and re-insert the wire if necessary.
  • **Loose Connection**: Verify that the operating lever is fully closed and locked into place.
  • **No Power**: Double-check all connections in the circuit, including the power source and the wires leading to and from the connector. Ensure the power supply is active.

6. Specifications

Feature Specification
Rated Voltage 250V
Rated Current 32A
Rated Impulse Voltage 4KV
Single or Plurality Hard Wire 0.08~2.5mm² / 28-12AWG
Multi Soft Wire 0.08~4mm² / 28-12AWG
Strip Length 9-10mm
Shell Material PC
Connection Material Red Copper
Certification CE
Origin Mainland China

6.1. Model-Specific Connection Methods

  • **QHJ-P421A**: 1 input 1 output
  • **QHJ-P422A**: 2 input 2 output
  • **QHJ-P423A**: 3 input 3 output
  • **QHJ-P424**: 4 input 4 output
  • **QHJ-P425**: 5 input 5 output
Dimensions and specifications for QHJ-P421A (1 input 1 output) wire connector.

Figure 4: QHJ-P421A (1 input 1 output) specifications and circuit diagram.

Dimensions and specifications for QHJ-P422A (2 input 2 output) wire connector.

Figure 5: QHJ-P422A (2 input 2 output) specifications and circuit diagram.

Dimensions and specifications for QHJ-P423A (3 input 3 output) wire connector.

Figure 6: QHJ-P423A (3 input 3 output) specifications and circuit diagram.

Dimensions and specifications for QHJ-P424 (4 input 4 output) wire connector.

Figure 7: QHJ-P424 (4 input 4 output) specifications and circuit diagram.

Dimensions and specifications for QHJ-P425 (5 input 5 output) wire connector.

Figure 8: QHJ-P425 (5 input 5 output) specifications and circuit diagram.

6.2. Rail Base Specifications

Dimensions and specifications for QHJ-DK42 rail base.

Figure 9: QHJ-DK42 rail base specifications.

Dimensions and specifications for QHJ-DZ43 rail base.

Figure 10: QHJ-DZ43 rail base specifications.

7. Warranty and Support

This product meets the CE marking requirements of the EU market and complies with the EU Low Voltage Directive (2014/35/EU) and Electromagnetic Compatibility Directive (2014/30/EU).

References to the relevant harmonised standards used or references to the other technical specifications in relation to which conformity is declared:

  • EN 60998-1:2004, EN IEC 61000-3-2:2019+A1:2021
  • EN 61000-3-3:2013+A1:2019+A2:2021
  • EN IEC 61000-6-1:2019, EN IEC 61000-6-3:2021

For any support inquiries or issues, please contact the seller directly.

8. User Tips

  • Always double-check the wire stripping length to prevent loose connections or arcing.
  • When splicing multiple connectors, ensure they are securely interlocked to maintain electrical integrity.
  • For permanent installations, consider using the compatible guide rails and bases for a neat and secure setup.
  • Before finalizing any electrical work, perform a continuity test to ensure all connections are sound and safe.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.