1. Introduction
The Kiprim WM01 is a non-contact, pinless inductive moisture meter designed for quick and non-destructive measurement of moisture content in various materials such as wood, masonry, and walls. It features a large LCD screen, multiple measurement modes, audible and visual alarms, data hold function, automatic shutdown, and a mute function for convenient and efficient moisture detection.

2. Product Overview
Familiarize yourself with the components and display elements of your Kiprim WM01 moisture meter.

Display Elements:
- Moisture Content Level Icon: Indicates the general moisture level (Dry, Mid, Wet).
- Measurement Mode Display: Shows the currently selected material mode (WALL, MASONRY, SOFT WOOD, HARD WOOD).
- Moisture Level Bar Display: A graphical representation of the moisture level.
- Hold Icon: Appears when the data hold function is active.
- Measurement Value Display: Shows the numerical moisture percentage.
- Battery Status Icon: Indicates the remaining battery life.
Buttons:
- On/Off Button: Powers the device on or off.
- Measurement Mode Selection Button (M): Cycles through different material modes.
- Mute/Hold Button (H): Toggles the sound alarm and activates/deactivates the data hold function.
Other Components:
- Abrasion Resistant Mats: Located on the back for durability and grip.
- Measurement Sensor Area: The area on the back of the device that should be placed against the surface for measurement.
- Moisture Content Table: Printed on the back, provides reference ranges for different materials.
- Battery Compartment: Located on the back for battery installation.
3. Setup
3.1 Battery Installation
- Locate the battery compartment on the back of the device.
- Open the battery compartment cover.
- Insert a 9V battery, ensuring correct polarity (+/-).
- Close the battery compartment cover securely.
3.2 Powering On/Off
- Press the On/Off button (power symbol) to turn the device on.
- Press and hold the On/Off button to turn the device off.
- The device features automatic shutdown to conserve battery life if inactive for a period.
4. Operating Instructions
4.1 Selecting Measurement Mode
Press the 'M' (Mode) button to cycle through the available material modes:
- WALL
- MASONRY
- SOFT WOOD
- HARD WOOD
Ensure the correct mode is selected for the material you are testing to obtain accurate readings.
4.2 Taking a Measurement
- Select the appropriate measurement mode for your material.
- Place the measurement sensor area (on the back of the device) flat against the surface you wish to test.
- Ensure your hand is kept away from the sensor area to ensure precise readings.
- The device will display the moisture content percentage on the LCD screen.
- The moisture content level icon and bar display will also provide a visual indication (Dry, Mid, Wet).


4.3 Interpreting Readings and Alarms
The WM01 provides both visual and audible alarms to indicate moisture levels:
- DRY: Green indicator light, silent (or single beep if mute is off).
- MID: Yellow indicator light, slow beep.
- WET: Red indicator light, fast beep.

Refer to the Moisture Content Table on the back of the device or in the Specifications section for specific percentage ranges for each material type.
4.4 Data Hold Function
Press the 'H' (Hold) button to freeze the current measurement on the display. Press 'H' again to release the hold and resume live measurements.
4.5 Mute Function
Press and hold the 'H' button to toggle the audible alarm on or off. This is useful for measurements in quiet environments.
4.6 Optimal Measurement Thickness
For accurate results, the ideal measurement thickness is 20-40mm (0.78-1.57 inches). Be aware that metallic concrete and drywall can affect measurement accuracy.

5. Maintenance
- Cleaning: Wipe the device with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Storage: Store the device in a cool, dry place away from direct sunlight and extreme temperatures. If storing for extended periods, remove the battery to prevent leakage.
- Battery Replacement: Replace the 9V battery when the battery status icon indicates low power. Refer to section 3.1 for battery installation instructions.
6. Troubleshooting
Common Issues and Solutions:
- No Power:
- Check if the battery is installed correctly with the right polarity.
- Replace the 9V battery with a fresh one.
- Inaccurate Readings:
- Ensure the correct material mode (WALL, MASONRY, SOFT WOOD, HARD WOOD) is selected.
- Verify that the measurement sensor area is placed flat against the surface.
- Keep your hand away from the sensor area during measurement.
- Avoid measuring on metallic surfaces, metallic concrete, or drywall, as these can affect accuracy.
- Ensure the material thickness is within the optimal range of 20-40mm (0.78-1.57 inches).
- No Audible Alarm:
- Press and hold the 'H' button to ensure the mute function is not active.
- Cannot detect deep water leaks (e.g., copper pipes in cement):
- The WM01 is designed for non-destructive surface moisture detection up to approximately 19mm deep. It may not be suitable for detecting leaks from deeply buried pipes, especially if the surrounding material is metallic or too thick. Its primary function is to identify moisture content in the immediate surface and sub-surface layers of common building materials.
7. Specifications
| Feature | Detail |
|---|---|
| Brand Name | Kiprim |
| Model Number | WM01 |
| Display Type | DIGITAL |
| With Backlight | Yes |
| DIY Supplies | Electrical |
| Battery Included | No (Requires 9V battery) |
| High-concerned chemical | None |
| Origin | Mainland China |
| Certification | CE |
| Measurement Depth | Up to 19mm (0.75 inches) |
| Optimal Measurement Thickness | 20-40mm (0.78-1.57 inches) |
Moisture Level Ranges:
| Material | DRY | MID | WET |
|---|---|---|---|
| Wall | < 8% | 8-12% | > 12% |
| Masonry | < 13% | 13-21% | > 21% |
| Soft Wood | < 20% | 20-26% | > 26% |
| Hard Wood | < 12% | 12-16% | > 16% |

8. User Tips
- For best results, ensure the sensor is in full contact with the surface being measured.
- Always select the correct material mode to get the most accurate readings.
- Be mindful of the measurement depth (up to 19mm) and optimal thickness (20-40mm) when assessing moisture, especially for hidden issues.
- Avoid using the meter on surfaces with metallic components or behind metallic objects, as this can interfere with the inductive measurement.
- If you suspect a deep-seated leak (e.g., from pipes), this non-invasive meter can help identify general areas of elevated moisture, but further investigation with specialized tools may be required to pinpoint the exact source.
9. Warranty & Support
For warranty information, technical support, or service inquiries, please contact Kiprim Official Store directly through the platform where you purchased the product. Keep your purchase receipt as proof of purchase.