Eletechsup NDUP1APA

Contents

NDUP1APA 15W UPS Module User Manual

Model: NDUP1APA | Brand: Eletechsup

1. Introduction

This manual provides detailed instructions for the Eletechsup NDUP1APA 15W 2-in-1 Charge and Boost UPS Module. This versatile module is designed to provide uninterrupted power supply (UPS) functionality for various electronic devices, particularly those powered by 3.7V/4.2V Lithium-ion or Lithium-polymer batteries. It integrates both charging and discharging capabilities with fast switching to ensure continuous operation during power outages.

Eletechsup NDUP1APA 15W UPS Module with key features highlighted
Figure 1: NDUP1APA 15W UPS Module highlighting 10ms fast switching, 15W output, 4.2V 600mA charging, and various voltage versions.

2. Safety Information

  • Ensure correct polarity when connecting power input, battery, and load. Incorrect connections can damage the module and connected devices.
  • Operate the module within the specified input and output voltage ranges.
  • Do not exceed the maximum output power of 15W.
  • Handle with care to avoid electrostatic discharge, which can damage sensitive electronic components.
  • Keep the module away from moisture and extreme temperatures.
  • This module is intended for use with 3.7V/4.2V Lithium-ion/Lithium-polymer batteries. Do not use with other battery chemistries.

3. Package Contents

  • 1 x NDUP1APA 15W 2-in-1 3.7V Charge and 5-25V Boost UPS Module

4. Specifications

ParameterValue
Module Type2-in-1 Charge and Discharger (Boost) UPS Module
Input VoltageDC 5V/6V/9V/12V/15V/24V (version dependent)
Output VoltageEqual to input voltage (Vout = Vin - 0.2~0.6V due to Schottky diodes)
Output Power15W (Maximum)
Full Charge Voltage4.20V (±1%)
Power Off Switching Time10ms
Operating Ambient Temperature-40°C to +85°C
Storage Temperature-65°C to +125°C
Dimensions60mm x 18mm x 6mm (Suitable for 18650 battery)
Weight8g

Version-Specific Parameters

VersionInput VoltageInput CurrentCharge VoltageCharge CurrentOutput VoltageOutput Current
5VDC 5-5.5V0.6-3.6A4.2V0.6A5V0-3A
6VDC 6-6.5V0.6-3.2A4.2V0.6A6V0-2.6A
9VDC 9-10V0.4-2.1A4.2V0.6A9V0-1.7A
12VDC 12-13V0.3-1.6A4.2V0.6A12V0-1.3A
15VDC 15-16V0.25-1.25A4.2V0.6A15V0-1A
24VDC 24-25V0.20-0.7A4.2V0.6A24V0-0.5A
Table of input and output parameters for different voltage versions of the UPS module.
Figure 2: Input and Output Parameters for various module versions.

5. Setup

5.1 Pin Description

Identify the connection points on the module using the diagram below:

  • IN+ : Power Input Positive
  • IN- : Power Input Negative
  • B+ : Battery Charging Positive
  • B- : Battery Charging Negative
  • OUT+: Load Output Positive
  • OUT- : Load Output Negative
Diagram showing the pinout of the NDUP1APA UPS module.
Figure 3: Pin Description of the NDUP1APA Module.

5.2 Component Identification

For advanced users or troubleshooting, the main components on the board are identified below:

Diagram identifying key components on the UPS module board, including boost chip, charging chip, protection chip, and inductor.
Figure 4: Key Components of the NDUP1APA Module.
  • High power shielded inductor
  • 10A high power boost chip
  • 1-Cell dedicated charging chip
  • Wide voltage DC-DC conversion chip
  • High power battery protection chip
  • 10MS fast switching chip
  • 10A high power Schottky diode

5.3 Wiring Diagram

Connect your power input, 3.7V Lithium battery, and load to the module as shown in the diagram. Ensure all connections are secure and correctly polarized.

Wiring diagram showing connections for input, battery, and output, illustrating direct power supply, charging, and discharging paths.
Figure 5: Basic Wiring and Working Principle.

5.4 Advanced Configuration: Resistor Modification

The charging current and output voltage can be adjusted by modifying specific resistors on the board. This requires soldering skills and appropriate tools.

Diagram illustrating how to modify R6 resistor to change charging current and R1 resistor to change output voltage.
Figure 6: Resistor Modification for Charging Current (R6) and Output Voltage (R1).

Modifying Charging Current (R6)

The default charging current is 600mA. You can change it by replacing the R6 resistor with a different value, as per the table below:

Resistor PackageR6 ValueIBAT (Charging Current)
080512.1 kΩ100mA
6.04 kΩ200mA
2.4 kΩ500mA
2 kΩ600mA
(Default)600mA
08051.2 kΩ1000mA

Modifying Output Voltage (R1)

The output voltage can be changed by replacing the R1 resistor with a different value, as per the table below:

Resistor PackageR1 ValueVout (Output Voltage)
080517.8 kΩ5V
24.9 kΩ6V
49.9 kΩ9V
75 kΩ12V
100 kΩ15V
174 kΩ24V

6. Operating Instructions

6.1 Working Principle

The NDUP1APA module operates based on the following principles:

  1. When an input voltage is supplied to the IN+ and IN- ports, the output port (OUT+ and OUT-) will provide a voltage approximately 0.2-0.6V lower than the input voltage. This is due to the voltage drop across the internal Schottky diodes.
  2. If a connected battery is not fully charged, the module will automatically initiate charging.
  3. In the event of a power outage (input voltage disappears), the module will automatically switch to battery discharge mode. The battery's voltage will be boosted and supplied to the output port, ensuring uninterrupted power to the connected load. The maximum discharge power is 15W.

6.2 Applications

The NDUP1APA module is suitable for a variety of applications requiring uninterrupted power or battery management:

  • UPS for WIFI Routers and Network Equipment: Provides continuous power to maintain network connectivity during power fluctuations or outages.
  • UPS for Industrial Equipment: Ideal for PLC/HMI/industrial control hosts to prevent data loss or operational interruptions.
  • Battery Powered Equipment: Can be integrated into devices that rely on 3.7V Li-ion/Li-po batteries (e.g., 18650, 14500).
  • DIY UPS Power Supply: For custom electronic projects requiring backup power.
  • Solar Charging Systems: Can be used in conjunction with solar panels for charging lithium batteries.
  • Electronic DIY Kits: A core component for various hobbyist and educational projects.
Diagram illustrating three application modes: UPS, Charger, and Booster, showing how the module functions in each scenario.
Figure 7: Application Examples (UPS, Charger, Booster).

7. Maintenance

  • Keep the module clean and free from dust and debris.
  • Regularly inspect connections for any signs of wear or corrosion.
  • Store the module in a dry, cool environment when not in use.
  • Avoid physical shock or excessive vibration.

8. Troubleshooting

  • No Output Power: Check input power supply, battery connection, and ensure the battery is charged. Verify all wiring polarities.
  • Battery Not Charging: Ensure input voltage is present and within the specified range for your module version. Check battery connections.
  • Module Overheating: Ensure the load does not exceed 15W. Provide adequate ventilation around the module.
  • Frequent Switching to Battery: Check the stability of your input power supply.

9. User Tips

No specific user tips were available from provided reviews or Q&A content. General advice includes:

  • For optimal performance, use high-quality 3.7V Lithium-ion or Lithium-polymer batteries.
  • Consider adding a heatsink if operating at maximum load for extended periods, especially in enclosed spaces.
  • When modifying resistors for custom voltage/current, double-check calculations and connections before applying power.

10. Warranty and Support

For detailed product information, technical support, or warranty inquiries, please refer to the official Eletechsup documentation or contact your retailer. A detailed manual may be available for download at the following link: https://1drv.ms/u/s!Av4PLxH_z8f1v1mtg2CoRsOScm2T?e=jLRvnO

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.