NJTY T88A T88B T88C

Contents

NJTY T88A T88B T88C Analog Multimeter Instruction Manual

Model: T88A, T88B, T88C

Brand: NJTY

1. Introduction

Thank you for choosing the NJTY T88 series analog multimeter. This high-precision instrument is designed for various electrical measurements, including AC/DC voltage, DC current, and resistance. It features a clear pointer display and robust protection circuits, making it an essential tool for electrical DIY, maintenance, and testing.

This manual provides detailed instructions for the safe and effective use of your multimeter. Please read it thoroughly before operation and keep it for future reference.

2. Model Overview

The NJTY T88 series includes models T88A, T88B, and T88C, each offering specific features:

Comparison of T88A, T88B, and T88C Multimeter Models

Figure 2.1: Comparison of T88A, T88B, and T88C Multimeter Models

Table 2.1: Key Differences Between T88 Models
FeatureT-88A (Standard)T-88B (Upgrade)T-88C (Elite)
Gears242424
MagnetismInternal MagneticInternal MagneticExternal Magnetism
Infrared Remote Control DetectionNoYesYes
Firewire IdentificationNoYesNo
Resistance MeasurementRx10kRx10kRx100k

3. Product Components

Familiarize yourself with the parts of your multimeter:

Labeled diagram of T88C Multimeter components

Figure 3.1: T88C Multimeter Components

  1. Pointer Display: Analog scale for reading measurements.
  2. Pointer Zero Adjustment: Knob to set the pointer to zero before measurements.
  3. Resistance Zero Adjustment: Knob to calibrate resistance measurements.
  4. Function Gear Dial: Rotary switch to select measurement type and range.
  5. 2500V Voltage Jack: Input terminal for high voltage measurements.
  6. 10A Current Jack: Input terminal for high current measurements.
  7. Protective Soft Rubber Sleeve: Provides durability and grip.
  8. Transistor Jack: For testing transistors (hFE).
  9. Red Test Pen Socket: Positive (+) input for test leads.
  10. Black Test Pen Socket (COM): Common/Negative (-) input for test leads.
  11. Suspension Support/Back Magnet: For convenient placement and hands-free operation.

4. Setup and Initial Checks

4.1. Battery Installation

The multimeter requires two AAA batteries for operation. Follow these steps to install them:

Battery compartment and fuse location on the back of the multimeter

Figure 4.1: Battery and Fuse Compartment

  1. Locate the battery compartment on the back of the multimeter.
  2. Open the battery cover.
  3. Insert two 1.5V AAA batteries, ensuring correct polarity.
  4. Close the battery cover securely.

The device is equipped with an anti-burning resettable fuse (voltage below 250V) and includes two spare fuses for easy replacement.

4.2. Connecting Test Leads

Insert the red test lead into the red test pen socket (+) and the black test lead into the black test pen socket (COM/-).

4.3. Pointer Zeroing

Before taking any measurements, especially for resistance, ensure the pointer is at the zero mark on the scale. Use the 'pointer zero adjustment' knob if necessary.

Video 4.1: Demonstrating pointer zero adjustment and various measurements.

5. Operating Instructions

Always select the appropriate function and range before connecting the test leads to the circuit. If the measurement value is unknown, start with the highest range and decrease it until a stable reading is obtained.

5.1. AC Voltage Measurement

  1. Set the function gear dial to the desired ACV range (e.g., 250V, 500V).
  2. Connect the test leads in parallel across the AC voltage source.
  3. Read the voltage value from the ACV scale on the pointer display.
AC Voltage Measurement demonstration

Figure 5.1: AC Voltage Measurement. The display shows 226V.

5.2. DC Voltage Measurement

  1. Set the function gear dial to the desired DCV range (e.g., 10V, 50V).
  2. Connect the red test lead to the positive (+) side and the black test lead to the negative (-) side of the DC voltage source.
  3. Read the voltage value from the DCV scale on the pointer display.
DC Voltage Measurement demonstration

Figure 5.2: DC Voltage Measurement. The display shows 9V.

5.3. Resistance Measurement

  1. Set the function gear dial to the desired resistance range (e.g., x1K, x10K).
  2. Before measuring, short the test leads together and adjust the 'resistance zero adjustment' knob until the pointer reads zero.
  3. Connect the test leads across the component to be measured.
  4. Read the resistance value from the Ω scale.
Resistance Measurement demonstration

Figure 5.3: Resistance Measurement. The display shows 10kΩ.

5.4. Continuity Test (On and Off Beep)

  1. Set the function gear dial to the 'BUZZ' or continuity setting.
  2. Connect the test leads across the circuit or component.
  3. If the resistance is below approximately 30Ω, the multimeter will emit an audible beep, indicating continuity.

5.5. Diode/Transistor Test

  1. Set the function gear dial to the diode/transistor test setting.
  2. For diodes, connect the test leads across the diode. Observe the reading for forward and reverse bias. A 10k resistor can be used to light up a diode for visual confirmation.
  3. For transistors, use the transistor jack (hFE) to test NPN/PNP types.

5.6. Battery Charge Measurement

  1. Set the function gear dial to the 'BATT' range (e.g., 1.5V, 9V).
  2. Connect the red test lead to the positive (+) terminal and the black test lead to the negative (-) terminal of the battery.
  3. Read the battery voltage from the display.

5.7. Infrared Remote Control Detection (T88B/T88C only)

  1. Set the function gear dial to the infrared detection setting.
  2. Point the infrared emitter of a remote control towards the multimeter's IR sensor.
  3. Press a button on the remote. The multimeter will indicate if an infrared signal is detected.

5.8. Capacitor Good/Bad Test

  1. Select the appropriate gear for the resistor:
    • Less than 0.01uF: choose x10K
    • 1-10uF: choose x1K
    • Above 10uF: choose x100 or x10 gear
  2. For each measurement, short-circuit the capacitor with a wire, and then perform the next measurement after discharging.
  3. For electrolytic capacitors, the positive electrode has higher than the negative electrode potential when in use. The black test lead is connected to the meter's common (COM) terminal. The positive lead of the battery is connected to the positive electrode of the electrolytic capacitor, and the red test lead is connected to the negative electrode of the capacitor.

6. Specifications

Table of detailed specifications for 88A, 88B, 88C multimeters

Figure 6.1: Detailed Specifications for T88A, T88B, T88C

Table 6.1: General Specifications
ParameterValue
Operating ModeManual Range
Operating Temperature0 - 40 ℃
DIY SuppliesElectrical
CertificationCE
Dimensions179*118*50mm
Display TypePointer Display
Power Supply1.5V AAA*2
Weight400g
Circuit BoardDouble-sided gold-plated circuit board
Protection24 files automatic protection, automatic recovery circuit, overload protection against false detection, quick-blow fuse tube
Table 6.2: Measurement Ranges and Accuracy
FunctionRangeAccuracy
DC Voltage0.25V-1V-2.5V-10V-50V-250V-500V-1000V-2500V±5%
AC Voltage0-10V-50V-250V-500V-1000V-250V±5%
DC Current50uA-0.5mA-5mA-50mA-500mA-10A±5%
DC ResistanceRx1-Rx10-Rx100-Rx1k-Rx10k-Rx100k±10%
Standard Resistance Box0.025/0.5/5/50/500/5k/20k/50k/200k/1M/2.25M/4.5M/9M/22.5MN/A
Access BeepBuzzer works when below 30ΩN/A
LV DetectionRx1-x1k-Rx1kN/A
Zener Tube/LED DetectionZener tube within 10V, detection current: DC 5mA (L type only)N/A
Battery Power Infrared Remote Control Detection1.2V/1.5V/2V/3V/3.6V (Only A/B/C types)N/A
Zero Line ResolutionYes (Type B only)N/A

7. Maintenance

7.1. General Care

  • Keep the multimeter clean and dry. Wipe the casing with a soft, damp cloth. Do not use abrasive cleaners or solvents.
  • Store the multimeter in a cool, dry place away from direct sunlight and extreme temperatures.
  • Avoid dropping the device or subjecting it to strong impacts.

7.2. Fuse Replacement

The multimeter is equipped with a quick-blow fuse for overload protection. If the multimeter stops functioning correctly, especially after an overload, the fuse may need replacement.

Location of spare fuses and main fuse on the multimeter back

Figure 7.1: Fuse Location

  1. Ensure the multimeter is turned off and disconnected from any circuit.
  2. Open the battery compartment cover on the back of the device.
  3. Carefully remove the old fuse.
  4. Replace it with a new fuse of the correct rating (check the specifications or the old fuse for details). Spare fuses are typically located within the battery compartment.
  5. Close the battery compartment cover securely.

8. Troubleshooting

If your multimeter is not functioning as expected, consider the following common issues:

  • No display/No power: Check if the batteries are correctly installed and have sufficient charge. Replace batteries if necessary.
  • Incorrect readings: Ensure the function dial is set to the correct measurement type and range. Verify that the test leads are properly connected and not damaged. Perform pointer zeroing and resistance zero adjustment before measurement.
  • No continuity beep: Check if the 'BUZZ' function is selected and if the circuit resistance is indeed below 30Ω.
  • No response in a specific function: The fuse for that function range might be blown. Refer to Section 7.2 for fuse replacement.

If the problem persists after checking these points, contact customer support for further assistance.

9. User Tips

  • Always start with a higher range when measuring an unknown value to prevent overloading the meter.
  • Ensure good contact between the test probes and the circuit points for accurate readings.
  • For resistance measurements, always disconnect power from the circuit and discharge any capacitors before testing.
  • Utilize the suspension support or back magnet for hands-free operation when working on complex circuits.

10. Warranty and Support

This product is covered by a standard manufacturer's warranty against defects in materials and workmanship. For warranty claims or technical support, please refer to the seller's contact information provided at the time of purchase. Keep your purchase receipt as proof of purchase.

For any questions regarding the operation or maintenance of your NJTY multimeter, please consult this manual or reach out to the authorized service center.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.