Flipsky Dual FSESC 6.9

Contents

Flipsky Dual FSESC 6.9 ESC Motor Controller User Manual

Model: Dual FSESC 6.9

1. Introduction

The Flipsky Dual FSESC 6.9 is a high-performance Electronic Speed Controller (ESC) designed for various electric mobility and robotics applications, including electric skateboards, ebikes, scooters, and robots. Based on the VESC 6 platform, this dual ESC offers robust power delivery and precise control for two motors, housed in a durable aluminum case for enhanced heat dissipation and protection.

Front view of the Dual FSESC 6.9 with main power and motor wires.
Figure 1: Front view of the Dual FSESC 6.9 with main power and motor wires.

2. Safety Information

Please read and understand all safety warnings and instructions before using the Dual FSESC 6.9. Failure to follow these instructions may result in electric shock, fire, serious injury, or property damage.

  • Always disconnect the battery before making any connections or performing maintenance.
  • Ensure all wiring is correct and secure to prevent short circuits.
  • Operate within the specified voltage and current limits to avoid damage to the ESC and connected components.
  • Keep the ESC away from water, moisture, and extreme temperatures.
  • Mount the ESC in a well-ventilated area to ensure proper cooling.
  • Use appropriate personal protective equipment (PPE) when working with electrical components.

3. Specifications

FeatureSpecification
Hardware VersionV6.9
Firmware Versionfw5.2 (Latest Version)
Continuous Current100A (single), 200A (total dual)
Peak Instantaneous Current400A (single), 800A (total system)
Voltage Range8V-60V (Safe for 4S to 12S LiPo, voltage spikes not to exceed 60V)
BEC Output5V@1A for external electronics
ERPM150000
Control Interface PortsUSB, CAN, UART
Supported SensorsABI, HALL, AS5047, AS5048A
Input Set SupportPPM, ADC, NRF, UART, SPI, IIC
Operating ModesDC, BLDC, FOC (sinusoidal)
Regenerative BrakingYes
ProgrammableYes
Motor Wire Gauge10AWG
Power Cable Gauge8AWG
Dimensions (with Alu case)127.6mm x 78.4mm x 32.5mm
Dimensional drawing of the Dual FSESC 6.9 with aluminum case.
Figure 2: Dimensions of the Dual FSESC 6.9 with aluminum case.

4. Package Contents

The package typically includes the following items:

  • 1x Flipsky Dual FSESC 6.9 ESC Motor Controller with Aluminum Case
  • Necessary connection cables (e.g., motor phase wires, battery cables, sensor cables, USB cable)
Top view of the FSESC 6.9 with motor wires and connected Hall sensor cables.
Figure 3: Top view of the FSESC 6.9 showing various connections.

5. Setup and Installation

Proper installation is crucial for the performance and longevity of your ESC. Follow these general steps:

  1. Mounting: Securely mount the ESC in a location that allows for adequate airflow and protects it from physical damage, moisture, and debris. The aluminum case acts as a heatsink, so ensure it's not obstructed.
  2. Motor Connections: Connect the three phase wires (A, B, C) from each motor to the corresponding terminals on the ESC. Ensure correct phasing for proper motor rotation.
  3. Sensor Connections (Optional): If your motors have Hall sensors, connect the sensor cables to the designated HALL ports on the ESC.
  4. Battery Connection: Connect the main power cables (B+ and B-) from your battery to the corresponding terminals on the ESC. Pay close attention to polarity (Red for positive, Black for negative).
  5. Control Interface: Connect your chosen input device (e.g., PPM receiver, UART module) to the appropriate control interface port on the ESC.
  6. Programming: Use the VESC Tool software (available online) to configure the ESC parameters, perform motor detection, and set up your control input. Connect the ESC to your computer via the USB port.
Top view of the Dual FSESC 6.9 showing port labels.
Figure 4: Top view of the Dual FSESC 6.9 with port labels.

6. Wiring Diagram

The following diagram illustrates the typical wiring connections for the Dual FSESC 6.9. Always refer to this diagram and ensure all connections are correct before applying power.

Detailed wiring diagram for the Dual FSESC 6.9, showing connections for motors, battery, and control interfaces.
Figure 5: Detailed Wiring Diagram for Dual FSESC 6.9. Note: Press to unplug connectors; do not pull directly to avoid damage.

Key to Wiring Diagram Ports:

  • Motor Connections: C1, B1, A1 (Motor 1); C2, B2, A2 (Motor 2)
  • Battery Connections: B+ (Positive), B- (Negative)
  • Control Interface Ports:
    1. CAN (Controller Area Network)
    2. SWD (Serial Wire Debug)
    3. PPM (Pulse Position Modulation)
    4. COMM (Communication Port)
    5. HALL (Hall Sensor Input)
    6. CAN (Controller Area Network)
    7. SWD (Serial Wire Debug)
    8. PPM (Pulse Position Modulation)
    9. COMM (Communication Port)
    10. HALL (Hall Sensor Input)

7. Operating Instructions

Once the ESC is correctly installed and configured using the VESC Tool, operation involves controlling your motors via the chosen input method (e.g., remote control, joystick, or software commands). The ESC supports various modes including DC, BLDC, and FOC (Field-Oriented Control) for smooth and efficient motor control.

  • Ensure your battery is fully charged before operation.
  • Always perform a functional check of your system in a safe environment before full use.
  • Monitor motor and ESC temperatures during operation, especially under heavy loads.
  • Familiarize yourself with the VESC Tool for advanced settings and real-time data monitoring.

8. Troubleshooting

If you encounter issues, consider the following common troubleshooting steps:

  • No Power: Check battery connections, main power switch (if any), and ensure the battery is charged.
  • Motor Not Spinning: Verify motor phase wire connections, Hall sensor connections (if used), and re-run motor detection in VESC Tool. Check for any error codes in the VESC Tool.
  • Erratic Motor Behavior: Re-check all wiring for loose connections. Ensure Hall sensors are correctly connected and configured. Calibrate your input device (e.g., remote).
  • Overheating: Ensure the ESC has adequate airflow. Reduce load or check motor efficiency. Verify motor current limits in VESC Tool.
  • Communication Issues (USB/UART/CAN): Check cable connections. Ensure correct drivers are installed for USB. Verify baud rates and IDs for UART/CAN.
  • Firmware Issues: If issues persist, consider updating or re-flashing the firmware using the VESC Tool. Always back up your settings before updating firmware.

9. User Tips

  • For optimal performance and longevity, avoid consistently pushing the ESC to its peak instantaneous current limits.
  • Regularly check all connections for tightness and signs of wear.
  • Keep the aluminum case clean to maximize its heat dissipation capabilities.
  • Experiment with different motor settings in the VESC Tool to find the best balance of power and efficiency for your specific application.

10. Maintenance

The Dual FSESC 6.9 is designed for durability, but regular maintenance can extend its lifespan:

  • Cleaning: Periodically clean the ESC and its aluminum case to remove dust, dirt, and debris that can hinder heat dissipation. Use a soft brush or compressed air.
  • Connection Checks: Inspect all wire connections for corrosion, fraying, or looseness. Re-solder or replace wires as needed.
  • Firmware Updates: Keep the ESC firmware updated to the latest version to benefit from performance improvements and bug fixes. Always follow official update procedures.
  • Storage: When not in use for extended periods, store the ESC in a dry, cool place, disconnected from the battery.

11. Warranty and Support

For technical support, warranty claims, or any questions regarding your Flipsky Dual FSESC 6.9, please contact the seller or manufacturer directly. You can reach out via:

  • WhatsApp: +86 18473951878
  • Email: 17680775530@163.com

Please provide your product model and a detailed description of the issue when seeking support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.