ANDELI MIG-250ME

Contents

ANDELI MIG-250ME Multiprocess Welder User Manual

Model: MIG-250ME | Brand: ANDELI

Your comprehensive guide to setting up, operating, and maintaining your 3-in-1 Flux MIG, Lift TIG, and Stick welding machine.

Introduction

The ANDELI MIG-250ME is a versatile 3-in-1 multiprocess welding machine designed for Flux MIG, Lift TIG, and Stick welding applications. Featuring IGBT inverter technology, an LED digital display, and an MCU intelligent precision chip, this welder offers stable performance and ease of use. Its portable design makes it suitable for a wide range of materials including metal cage, mild steel, square pipe, aluminum, stainless steel, and cast iron.

ANDELI MIG-250ME Welder with accessories
Figure 1: ANDELI MIG-250ME Multiprocess Welder and included accessories.

Safety Information

WARNING: Welding can be dangerous. Always follow safety precautions to prevent injury or death.

  • Always wear appropriate personal protective equipment (PPE), including welding helmet, gloves, and protective clothing.
  • Ensure proper ventilation to avoid inhaling fumes.
  • Keep a fire extinguisher nearby.
  • Do not operate the welder in damp or wet conditions.
  • Ensure the work area is clear of flammable materials.
  • Disconnect power before performing any maintenance or adjustments.

Package Contents

Verify that all items are present in your package:

Included accessories for ANDELI MIG-250ME Welder
Figure 2: Standard accessories included with the MIG-250ME welder.
  • ANDELI MIG-250ME Welder Unit
  • MIG Torch (3m)
  • MMA Holder (Electrode Holder)
  • Ground Clamp
  • Flux-cored Wire (0.5KG)
  • Nozzles
  • Contact Tips
  • Tungsten Electrode (for TIG)
  • Hammer
  • Toolbox (may vary by package)

Setup Instructions

1. Power Connection

  • Ensure the welder is switched off before connecting to power.
  • Connect the welder to a stable 220V power supply.

2. Control Panel Overview

Front view of the ANDELI MIG-250ME control panel
Figure 3: Front panel of the MIG-250ME, showing controls and display.
Digital display screen with graphical interface
Figure 4: Close-up of the digital display screen, featuring a graphical interface for intuitive use.

The welder features an LED digital display and intuitive controls for adjusting welding parameters.

3. Welding Mode Connections

Connection points for TIG, AW, and MIG welding
Figure 5: Connection points for TIG, AW (Stick), and MIG welding modes.
  • MIG Welding: Connect the MIG torch to the designated MIG jack. Ensure the flux-cored wire (0.8mm or 1.0mm) is properly loaded into the wire feeder.
  • Lift TIG Welding: Connect the TIG torch to the TIG jack. Ensure a tungsten electrode is installed.
  • Stick (MMA/AW) Welding: Connect the electrode holder to the positive (+) terminal and the ground clamp to the negative (-) terminal.
  • Always ensure connections are secure before operation.
Wire feeder mechanism for 1KG welding wire
Figure 6: The wire feeder mechanism, designed to accommodate 1KG welding wire spools.

Operating Instructions

1. Power On and Mode Selection

  • Turn on the main power switch.
  • Select the desired welding process (Flux MIG, Lift TIG, or Stick) using the mode selection button on the control panel.

2. Parameter Adjustment

Control panel with PRO TYPE adjustment instructions
Figure 7: Instructions for PRO TYPE mode, allowing manual adjustment of current and voltage.
One-touch adjustment feature on the control panel
Figure 8: The one-touch adjustment feature simplifies setting welding parameters based on material thickness.
  • Synergy Adjustment: The machine features synergy adjustment, automatically matching wire feeder speed and welding current to actual working requirements.
  • Manual Mode (PRO TYPE): For fine-tuning, long-press the "SP MODE" knob for approximately 5 seconds to activate manual mode. This allows independent adjustment of current and voltage.
  • One-Touch Adjustment: Utilize the built-in welding parameters for quick setup, for example, selecting settings for 0.5mm or 0.8mm thickness.
  • Adjust welding current/voltage and wire feeding speed as needed for your specific application.

3. Welding Process

Visual representation of Flux MIG, Lift TIG, and Stick welding processes
Figure 9: The three welding processes supported: Flux MIG, Lift TIG, and Stick.
  • Begin welding according to the chosen process and adjusted parameters.
  • Maintain proper arc length and travel speed for optimal results.
  • The machine is designed for gasless MIG welding.

Maintenance

Regular maintenance ensures the longevity and optimal performance of your welder.

  • Cleaning: Periodically clean the exterior of the machine and the welding torch/holder to remove dust and debris. Use compressed air to clear internal components if necessary, ensuring the machine is unplugged.
  • Cable Inspection: Check all welding cables, power cords, and connections for wear, damage, or loose fittings. Replace damaged components immediately.
  • Wire Feeder: Inspect the wire feeder mechanism for any obstructions or wear. Ensure the wire spool rotates smoothly.
  • Contact Tips & Nozzles: For MIG welding, regularly inspect and replace worn contact tips and nozzles to ensure consistent wire feed and gas flow (if applicable for gas MIG, though this model is gasless).
  • Tungsten Electrodes: For TIG welding, ensure tungsten electrodes are properly sharpened and free from contamination.

Troubleshooting

This section provides solutions to common issues you might encounter.

ProblemPossible CauseSolution
Welder does not power onNo power supply; loose power cord; faulty power switch.Check power outlet and circuit breaker; ensure power cord is securely plugged in; contact support if switch is faulty.
No arc or weak arcImproper settings; poor ground connection; worn contact tip/electrode; incorrect wire feed speed.Adjust current/voltage settings; ensure ground clamp has good contact; replace contact tip/electrode; adjust wire feed speed.
Wire feeding issues (MIG)Kinked wire; clogged liner; incorrect tension on wire spool; worn drive roller.Straighten wire; clean/replace liner; adjust spool tension; inspect/replace drive roller.
Overheating protection activatedExceeded duty cycle; poor ventilation.Allow machine to cool down; ensure adequate airflow around the welder.

Specifications

FeatureDetail
Brand NameANDELI
ModelMIG-250ME
TypeCombination (Flux MIG/Lift TIG/Stick)
Rated Input Voltage220V
Rated Output Voltage17.9 V
Welding Current/Voltage Range20-120 A
Rated Duty Cycle @40°C (MIG)60%
Max. Load Power Capacity5.9
Wire Melting TypeGlobular Transfer
Wire Feeding Speed12 m/min
MIG Solid Wire Diameter0.8mm, 1.0mm
Welding Thickness0.6-5mm
MaterialPlastic (housing)
Material / Metal ProcessedStainless Steel, Mild Steel, Aluminum, Cast Iron, etc.
Dimensions370*155*290mm
Weight5 kg
FeatureIGBT Inverter, Portable, Synergy Adjustment
DIY SuppliesElectrical
OriginMainland China (Zhejiang)

User Tips

  • For beginners, start with the one-touch adjustment feature to quickly set up basic welding parameters.
  • Experiment with the "PRO TYPE" manual adjustment once you are comfortable with the basic settings to fine-tune your welds for specific projects.
  • Always ensure your workpiece is clean and free of rust or paint for the best welding results.
  • Take advantage of the synergy adjustment feature, which simplifies parameter setting by automatically adjusting wire feed speed and current.

Warranty and Support

The ANDELI MIG-250ME welder comes with a 1-Year Warranty from the date of purchase, covering manufacturing defects.

For technical support, troubleshooting assistance, or warranty claims, please contact us:

  • WhatsApp: +86 13789151640
  • Email: 15379569402@163.com

Our working hours are from 8:00 AM to 6:00 PM China time.

© 2023 ANDELI. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.