Hantek DSO3254A

Contents

Hantek DSO3254A Digital Oscilloscope User Manual

Model: DSO3254A

1. Introduction

The Hantek DSO3254A is a versatile 4-channel digital oscilloscope, logic analyzer, and multimeter designed for a wide range of electrical testing and measurement applications. This device offers a 250MHz bandwidth and a 1GSa/S real-time sampling rate, making it suitable for detailed signal analysis. Its compact design and USB connectivity provide flexibility for both benchtop and field use.

Hantek DSO3254A Oscilloscope, front view

Figure 1: Hantek DSO3254A Digital Oscilloscope

Hantek DSO3254A Oscilloscope, dimensions (190mm, 255mm, 45mm)

Figure 2: Device Dimensions (255mm x 190mm x 45mm)

2. Safety Information

Please read and understand all safety precautions before operating the device. Failure to follow these instructions may result in injury or damage to the instrument.

  • Always connect the ground lead of the probe to the circuit ground before connecting the probe input to the circuit under test.
  • Do not apply input voltages exceeding the maximum ratings specified in the technical specifications.
  • Ensure the power adapter used is within the specified voltage range (8-36V).
  • Avoid operating the device in wet or damp conditions.
  • Do not attempt to open or modify the device. Refer all servicing to qualified personnel.

3. Setup Guide

3.1 Unpacking and Contents

Carefully unpack the Hantek DSO3254A and verify that all standard accessories are present:

  • Hantek DSO3254A Oscilloscope Unit
  • Carrying Bag
  • Oscilloscope Probes (4x)
  • Power Adapter
  • USB Cable
  • Software Installation CD
Standard Accessories: Carrying bag, oscilloscope unit, probes, power adapter, USB cable, software CD.

Figure 3: Standard Accessories Included

3.2 Connecting to a Computer

The DSO3254A can be connected to a computer via USB or LAN/PoE for data transfer and control.

3.2.1 USB Connection

  1. Connect one end of the provided USB cable to the 'USB DEVICE' port on the DSO3254A.
  2. Connect the other end of the USB cable to an available USB port on your computer.

3.2.2 LAN/PoE Connection

  1. Connect an Ethernet cable to the 'LAN/PoE' port on the DSO3254A.
  2. Connect the other end of the Ethernet cable to your network switch or directly to your computer's Ethernet port. If using PoE, ensure your network switch supports Power over Ethernet.
Hantek DSO3254A Oscilloscope, left side ports (CH1-CH4, Logic In/Out)

Figure 4: Left Side Ports (CH1-CH4, Logic In/Out)

Hantek DSO3254A Oscilloscope, right side ports (LAN/PoE, USB Host, USB Device, Power)

Figure 5: Right Side Ports (LAN/PoE, USB Host, USB Device, Power)

Network connection diagram showing multiple oscilloscopes connected via PoE switch, fiber optic, and USB to a PC.

Figure 6: Example Network Connection Diagram

3.3 Powering On

  1. Connect the power adapter to the 'POWER' input on the DSO3254A.
  2. Plug the power adapter into a suitable electrical outlet.
  3. The device will power on automatically. Observe the 'POWER' indicator LED.

3.4 Software Installation

  1. Insert the provided software CD into your computer's CD/DVD drive.
  2. Follow the on-screen instructions to install the Hantek DSO software.
  3. If you do not have a CD drive, download the latest software from the official Hantek website.
  4. After installation, launch the Hantek DSO application. The software should automatically detect the connected oscilloscope.

4. Operating Instructions

4.1 Basic Oscilloscope Functions

The Hantek DSO software provides a graphical user interface to control the oscilloscope and display waveforms.

  • Channel Selection: Use the software interface to enable/disable channels (CH1-CH4).
  • Vertical Scale (Volts/Div): Adjust the vertical sensitivity for each channel to fit the signal amplitude on the screen.
  • Horizontal Scale (Time/Div): Adjust the time base to view the desired number of cycles of the waveform.
  • Trigger Settings: Configure the trigger mode (Edge, Pulse, Video, Slope, Timeout), source (CH1, CH2, CH3, CH4, EXT, EXT/10), and level to stabilize the waveform display.
  • Measurements: The software supports various auto measurements including Vpp, Vamp, Vmax, Vmin, Vtop, Vmid, Vbase, Vavg, Vrms, Vcrms, Preshoot, Overshoot, Frequency, Period, Rise Time, Fall Time, Positive Width, Negative Width, Duty Cycle. Cursors (Horizontal, Vertical, Cross) are also available for manual measurements.
Software screenshot showing a sine wave.

Figure 7: Sine Wave Display in Hantek DSO Software

Software screenshot showing multiple waveforms (CH1, CH2, CH3, CH4).

Figure 8: Multiple Channel Waveform Display

Software screenshot showing X-Y mode with an ellipse.

Figure 9: X-Y Mode Display

Software screenshot showing modulated waveform.

Figure 10: Modulated Waveform Display

Software screenshot showing math function (CH1+CH2).

Figure 11: Math Function Display (CH1+CH2)

4.2 Waveform Generator (AFG)

The DSO3254A includes a 1-channel arbitrary waveform generator with a frequency range of DC~25MHz and 12-bit vertical resolution.

  • Access the waveform generator settings within the Hantek DSO software.
  • Configure the waveform type (e.g., Sine, Square), frequency, amplitude, and offset.
  • Connect the output of the waveform generator to the desired circuit using appropriate cables.
Software screenshot showing a sine wave with settings panel.

Figure 12: Waveform Generator Settings (Sine Wave)

Software screenshot showing a square wave.

Figure 13: Waveform Generator Output (Square Wave)

4.3 Logic Analyzer (LA16)

The device features a 16-channel logic analyzer for digital signal analysis.

  • Connect the logic analyzer probes (special accessories, if purchased separately) to the 'LOGIC IN' port.
  • Connect the individual probe clips to the digital signals you wish to analyze.
  • Configure the logic analyzer settings in the software, including sampling rate and trigger conditions.
DSO3000A Series Special Accessories: BNC cable, logic analyzer probes.

Figure 14: Logic Analyzer Probes (Special Accessory)

5. Specifications

5.1 General Specifications

  • Brand Name: Hantek
  • Model Number: DSO3254A
  • DIY Supplies: Electrical
  • Certification: CE
  • Origin: Mainland China
  • Battery Included: No
  • IS Battery Demountable: No
  • High-concerned chemical: None
  • Size: 255 x 190 x 45 (mm)
  • Weight: 1Kg
  • Power Supply: 8~36V Wide range of input voltage
  • Interface: USB 2.0

5.2 Oscilloscope Specifications

Table 1: Oscilloscope Vertical and Horizontal Specifications
FeatureDSO3254A
Analog Channels4
Bandwidth250MHz
Rise Time1.4ns
Input ImpedanceResistance: 1MΩ; Capacitance: 25 pF
Input Sensitivity1mV/div to 10V/div
Input CouplingAC/DC/GND
Vertical Resolution8 bits
Memory Depth1.6K-128M/CH
Max. Input Voltage400V (DC+AC Peak)
Real-Time Sampling Rate1GSa/S
Time Base Range2ns/div to 1000s/div
Time Base Precision±50ppm
Trigger SourceCH1, CH2, CH3, CH4, EXT, EXT/10
Max Waveform Capture Rate30,000wfm/s
Record Length1.6K-128M
Voltage Range1mV to 10V/div @ x 1 probe; 10mV to 100V/div @ x 10 probe; 100mV to 1KV/div @ x 100 probe; 1V to 10KV/div @ x 1000 probe;
FFTRectangular, Hanning, Hamming, Blackman Window
Table 2: Waveform Generator Specifications
FeatureSpecification
Waveform FrequencyDC~25MHz
DAC Clock2K~200MHz adjustable
Frequency Resolution0.10%
Channel1CH
Waveform Length4K
Vertical Resolution12 Bits
Frequency Stability<30ppm
Waveform Amplitude±3.5V Max.
Output Impedance50 Ω
Output Current50mA
Bandwidth25M
Table 3: Logic Analyzer Specifications
FeatureSpecification
Channels16CH
Max. Input Impedance200KΩ (C=10pF)
Max. Input Voltage-60V~60V
Max. Sampling Rate250MSa/s
Bandwidth10MHz
Compatible InputTTL, LVTTL CMOS, LVCMOS, ECL, PECL, EIA
Memory Depth1.6K~64M

6. Maintenance

6.1 Cleaning

To clean the exterior of the instrument, use a soft cloth dampened with a mild detergent solution. Do not use abrasive cleaners or solvents that may damage the casing. Ensure the device is powered off and disconnected from all power sources before cleaning.

6.2 Storage

When not in use, store the DSO3254A in a dry, dust-free environment, away from direct sunlight and extreme temperatures. Use the provided carrying bag for protection during transport and storage.

7. Troubleshooting

If you encounter issues with your Hantek DSO3254A, refer to the following common troubleshooting steps:

  • Device not recognized by software: Ensure the USB cable is securely connected and the power adapter is plugged in. Try a different USB port or restart your computer. Verify that the Hantek DSO software is correctly installed.
  • No waveform displayed: Check probe connections to both the device and the circuit under test. Ensure the channel is enabled in the software and the vertical/horizontal scales are appropriately set. Adjust the trigger level.
  • Distorted or noisy waveforms: Check for proper grounding of the probes and the circuit. Ensure probes are correctly compensated. Reduce external electromagnetic interference.
  • Software crashes or freezes: Ensure your computer meets the minimum system requirements. Update the Hantek DSO software to the latest version.

8. User Tips

No specific user tips were available from provided reviews or Q&A. For optimal performance, always ensure your software is up-to-date and refer to the comprehensive software guide for advanced features.

9. Warranty and Support

Hantek products are typically covered by a manufacturer's warranty. For detailed warranty information, technical support, or service inquiries, please refer to the official Hantek website or contact your local distributor. Keep your purchase receipt as proof of purchase.

Video 1: Hantek DSO3254A Product Overview

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.