Teverun Blade Mini Ultra Controller 60V 25A

Contents

Teverun Blade Mini Ultra 60V 25A Brushless Controller User Manual

Model: Blade Mini Ultra Controller 60V 25A (TBL60V25A6G)

Brand: Teverun

1. Introduction

This manual provides essential information for the safe and effective use, installation, and maintenance of your Teverun Blade Mini Ultra 60V 25A Brushless Controller. This controller is specifically designed for the Blade Mini Ultra 60V 27Ah electric scooter (NON APP version) and is crucial for managing motor power and performance. Please read all instructions carefully before installation and operation.

Two Teverun Blade Mini Ultra 60V 25A Brushless Controllers, labeled L2-A and L2-B, showing specifications and wiring harnesses. A small image of a scooter is in the bottom right corner.
Figure 1: Teverun Blade Mini Ultra 60V 25A Brushless Controllers (L2-A and L2-B)

2. Safety Warnings

Important Safety Information: Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture.
  • General Warning: Please mind potential fire risk and strictly follow the instruction manual for proper handling and storage. While using the product, please wear protective equipment and fully comply with applicable laws and regulations.

3. Product Overview

The Teverun Blade Mini Ultra 60V 25A Brushless Controller is a key component for your electric scooter, managing the power delivery to the motor. It comes in two main variants, Controller A and Controller B, which may be used individually or as a pair (AB controller set) depending on your scooter's configuration.

Close-up view of two Teverun Brushless Controllers, L2-A and L2-B, showing detailed specifications printed on their casings.
Figure 2: Detailed view of Controller Specifications

Each controller unit features multiple wiring harnesses for connection to various scooter components such as the motor, battery, display, and other sensors. The controllers are designed for a 60V system with a 25A current limit.

Close-up of a single Teverun Controller A unit with its attached wiring harness.
Figure 3: Controller A
Close-up of a single Teverun Controller B unit with its attached wiring harness.
Figure 4: Controller B
Image showing a pair of Teverun AB controllers with their complete wiring harnesses.
Figure 5: A pair of AB Controllers

4. Specifications

Feature Specification
Product Name Brushless Controller
Model Number TBL60V25A6G
Voltage DC60V
Undervoltage Protection 46V
Limit Current 25A
Compatibility Blade Mini Ultra 60V 27Ah (NON APP Version)
Origin Mainland China

For detailed technical specifications and wiring diagrams, please refer to the official user manual PDF available at Teverun Controller User Manual (PDF).

5. Installation and Setup

Installation of the brushless controller requires technical knowledge and should ideally be performed by a qualified technician. Incorrect installation can lead to damage to the scooter or personal injury. Always ensure the scooter's power is completely off and the battery is disconnected before beginning any installation work.

  1. Preparation: Ensure you have the correct controller(s) (Controller A, Controller B, or an AB pair) for your Blade Mini Ultra scooter. Remove any protective films from the new controller(s).
  2. Access: Carefully open the scooter's deck or access panel to expose the existing controller(s) and wiring.
  3. Disconnection: Systematically disconnect all wires from the old controller(s), noting their positions and connections. It is highly recommended to take photos or draw a diagram of the existing wiring before disconnecting.
  4. Replacement: Mount the new Teverun controller(s) in the designated location.
  5. Wiring: Connect the wiring harnesses from the new controller(s) to the corresponding components (motor, battery, display, throttle, brake sensors, etc.). Pay close attention to color coding and connector types. The controllers feature various connectors for different functions:
    • Motor phase wires (typically thicker, often green, blue, yellow)
    • Hall sensor wires (smaller, multi-pin connector)
    • Battery power input (red/black, often with XT60 or similar connector)
    • Ignition/key switch wire
    • Throttle signal wire
    • Brake sensor wires
    • Display/meter connection
    • Other auxiliary connections (e.g., lights, horn)
    Teverun Blade Mini Ultra controllers with their complex wiring harnesses clearly visible, showing various connectors.
    Figure 6: Controller Wiring Harnesses
    Top view of the Teverun controllers showing the arrangement of the wiring connections.
    Figure 7: Top View of Controller Wiring
  6. Secure Connections: Ensure all connections are firm and properly seated. Avoid loose wires which can cause short circuits or intermittent operation.
  7. Testing: Before fully reassembling the scooter, perform a preliminary test to ensure the motor responds correctly to the throttle and brake inputs.
  8. Reassembly: Carefully reassemble the scooter, ensuring no wires are pinched or damaged.

Note: We DO NOT support any scooter modification. If you need any technical support, please contact the seller directly.

Warning message stating that scooter modification is not supported and to contact the seller for technical support.
Figure 8: Important Technical Support Notice

6. Operating Instructions

The brushless controller operates in conjunction with your scooter's display and throttle. Once correctly installed, its operation is integrated into the scooter's overall system.

  1. Power On: Turn on your electric scooter using its main power switch or key. The controller will initialize with the scooter's system.
  2. Throttle Control: Use the scooter's throttle to control acceleration. The controller will regulate power to the motor based on your input.
  3. Braking: Engage the scooter's brakes. The controller will cut power to the motor and may engage regenerative braking if supported by your scooter model.
  4. Mode Selection: If your scooter's display allows for different riding modes (e.g., Eco, Sport), the controller will adjust its power delivery characteristics accordingly. Refer to your scooter's main user manual for display and mode operation.

This controller is specifically for the NON APP version of the Blade Mini Ultra, meaning it does not require or support mobile application connectivity for its operation.

An electric scooter with the Teverun 60V 25A Controller, highlighting its compatibility with the NON APP version.
Figure 9: Controller for NON APP Blade Mini Ultra Scooter

7. Maintenance

Proper maintenance ensures the longevity and optimal performance of your controller.

  • Regular Inspection: Periodically check the controller and its wiring for any signs of damage, corrosion, or loose connections.
  • Cleanliness: Keep the controller free from dust, dirt, and debris. Use a dry, soft cloth for cleaning. Avoid using liquids or harsh chemicals.
  • Moisture Protection: Ensure the controller remains dry. While designed for scooter use, excessive exposure to water or moisture can cause damage.
  • Temperature: Avoid operating the scooter in extreme temperatures that could overheat the controller.
  • Storage: When not in use for extended periods, store the scooter (and thus the controller) in a dry, cool place, away from direct sunlight and extreme temperatures.

8. Troubleshooting

If you encounter issues with your scooter's performance after controller installation, consider the following common troubleshooting steps:

  • No Power/No Response:
    • Check all battery connections to ensure they are secure.
    • Verify the scooter's main power switch is ON.
    • Inspect the controller's power input wires for proper connection.
  • Motor Not Spinning/Intermittent Operation:
    • Ensure motor phase wires are correctly connected.
    • Check Hall sensor connections; a faulty Hall sensor can cause erratic motor behavior.
    • Verify throttle connection and functionality.
  • Error Codes on Display:
    • Refer to your scooter's main user manual for specific error code meanings. Many error codes relate to controller or motor issues.
  • Overheating:
    • Ensure the controller has adequate ventilation.
    • Avoid prolonged high-power usage, especially in hot weather.

If troubleshooting steps do not resolve the issue, or if you are unsure about any step, please contact professional technical support. Do not attempt complex repairs yourself unless you are qualified.

9. User Tips

  • Verify Compatibility: Always double-check that the controller model (TBL60V25A6G) is compatible with your specific Blade Mini Ultra 60V 27Ah (NON APP version) scooter before purchase and installation.
  • Professional Installation Recommended: Due to the complexity of electric scooter wiring, professional installation is highly recommended to prevent damage and ensure safety.
  • Document Wiring: Before disconnecting any wires, take clear photos or make detailed diagrams of your existing scooter's wiring. This will be invaluable during reinstallation.
  • Secure Connections: Ensure all electrical connections are tight and properly insulated to prevent short circuits and ensure reliable operation.

10. Warranty and Support

LOOMO Wheel Store guarantees that all goods sold are original and subject to rigorous quality checks. If there is any quality problem upon receiving the product, please contact the seller as soon as possible for a solution.

For technical support or any queries regarding the product, please contact the seller directly. All items are professionally packed with great care to ensure safe delivery.

You can also refer to the official user manual PDF for additional guides and documents: Teverun Controller User Manual (PDF).

Official Product Video

Video 1: Overview of the Teverun Blade Mini Ultra Brushless Controller, showcasing its design and components.

© 2024 Teverun. All rights reserved. This manual is for informational purposes only.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.