Nutri Ninja 7-in-1 Replacement Set

Contents

Nutri Ninja Blender 7-in-1 Replacement Parts Instruction Manual

For Models: BL450-30 Series, BL480-30 Series, BL487 - BL492 Series, CT680 Series, BL642-30 Series, BL680A Series, NN100 Series, NN210, CT640C, CT641, BN801

Introduction

This manual provides instructions for the installation, operation, and maintenance of your new 7-in-1 replacement parts set for Nutri Ninja blenders. These parts are designed to seamlessly replace old or damaged components, restoring your blender's functionality and extending its lifespan. Please read this manual thoroughly before using the replacement parts.

Package Contents

Please verify that all items listed below are included in your package:

  • 2 x 24oz (710ml) Blender Cups
  • 2 x Spout Lids
  • 1 x 7-Fin Male Blade Assembly
  • 4 x Seal Ring Gaskets
  • 1 x Hanger
Image showing all components of the 7-in-1 replacement set: two blender cups, two spout lids, one blade assembly, four seal ring gaskets, and one hanger.
Figure 1: Complete 7-in-1 Replacement Parts Set

Compatibility

This replacement parts set is compatible with the following Nutri Ninja blender models:

  • BL450-30 Series
  • BL480-30 Series
  • BL487 - BL492 Series
  • CT680 Series
  • BL642-30 Series
  • BL680A Series
  • NN100 Series
  • NN210
  • CT640C
  • CT641
  • BN801

Please ensure your blender model number matches one of the listed series for proper fit and function. The blade features 7 fins and is a male blade type.

Setup

Follow these steps to assemble your replacement parts:

  1. Inspect Gaskets: Before first use, ensure that a seal ring gasket is properly seated within the blade assembly. If replacing an old gasket, gently remove the old one and insert a new one from the package.
  2. Attach Blade to Cup: Place your ingredients into the 24oz blender cup. Align the 7-fin blade assembly with the top of the cup and twist clockwise until securely tightened. Ensure a tight seal to prevent leaks.
  3. Attach Spout Lid (for storage/travel): If preparing a drink to go, remove the blade assembly after blending and twist on a spout lid until it is securely fastened.
Blender cup with blade assembly attached, ready for blending.
Figure 2: Blade assembly attached to the blender cup.
Detailed view of the blender cup, spout lid, and seal ring gasket, highlighting their features.
Figure 3: Close-up of cup, lid, and gasket for proper assembly.

Operating Instructions

These replacement parts function identically to your original Nutri Ninja components. Always refer to your main Nutri Ninja blender manual for specific blending instructions and safety precautions.

  1. Fill the Cup: Add your desired ingredients to the 24oz cup. Do not exceed the "MAX LIQUID" fill line indicated on the cup.
  2. Attach Blade: Securely twist the 7-fin blade assembly onto the cup.
  3. Blend: Invert the cup and blade assembly onto your Nutri Ninja blender base. Twist to lock it into place and operate the blender according to your blender's instructions.
  4. Serve or Store: Once blending is complete, remove the cup from the blender base. Carefully detach the blade assembly. If consuming immediately, pour into a glass. If taking on the go, attach a spout lid.
Two blender cups with spout lids, filled with blended juice, ready for consumption.
Figure 4: Blended beverages in cups with spout lids.

Maintenance and Cleaning

Proper cleaning and maintenance will ensure the longevity of your replacement parts.

  • Dishwasher Safe: The replacement blades, cups, and lids are dishwasher-safe for convenient cleaning.
  • Hand Washing: For hand washing, use warm, soapy water and a non-abrasive sponge or brush. Rinse thoroughly.
  • Gasket Care: Periodically inspect the seal ring gaskets for any signs of wear, cracking, or damage. Replace them with new gaskets from the package if necessary to maintain a leak-proof seal.
  • Blade Care: Handle the blade assembly with care due to sharp edges. Ensure it is thoroughly cleaned after each use, especially around the fins, to prevent residue buildup.

Troubleshooting

ProblemPossible CauseSolution
Leaking during blendingBlade assembly not tightened sufficiently; damaged or improperly seated seal ring gasket.Ensure the blade assembly is twisted tightly onto the cup. Check the seal ring gasket for proper placement and condition; replace if damaged.
Blender not activating with new cup/bladeCup/blade not properly aligned or locked onto the blender base.Ensure the cup and blade assembly are correctly aligned and twisted securely onto the blender base until it locks into place. Refer to your blender's main manual.

Specifications

FeatureDetail
MaterialPlastic (cups, lids), Stainless Steel (blade)
Blade Type7-Fin Male Blade, 2.4mm thick
Cup Capacity24 oz (710 ml)
Cup DimensionsApproximately 4 inches (diameter) x 7.5 inches (height)
ColorBlack (blade assembly, lids), Clear (cups)
Dishwasher SafeYes (blades, cups, lids)
Package Weight0.818 kg
Package Dimensions24 cm (Length) x 21 cm (Width) x 11 cm (Height)
Diagram showing the dimensions of the 24oz blender cup: 4 inches diameter and 7.5 inches height.
Figure 5: Blender Cup Dimensions

User Tips

  • Extra Cups for Convenience: With two 24oz cups included, you can prepare multiple smoothies or juices throughout the day, or share with family members without immediate washing.
  • Verify Compatibility: Always double-check your specific Nutri Ninja blender model number against the compatibility list provided in this manual to ensure a perfect fit.
  • Tighten Securely: To prevent leaks and ensure optimal blending, always twist the blade assembly onto the cup very securely before placing it on the blender base.

Warranty and Support

For any questions regarding the installation or performance of these replacement parts, please contact the seller or manufacturer directly. Keep your purchase receipt for any potential support inquiries.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.