Concord MC-880

Contents

Concord MC-880 Screw Air Compressor Controller User Manual

Model: MC-880 | Brand: Concord

1. Introduction

Welcome to the user manual for the Concord MC-880 Screw Air Compressor Controller. This robust display panel is designed for efficient and reliable control of screw air compressors. This manual provides essential information for proper installation, operation, maintenance, and troubleshooting to ensure optimal performance and longevity of your controller.

2. Product Overview

The MC-880 controller features a clear display and intuitive button interface for managing your air compressor. It is designed for integration into industrial electrical systems.

2.1 Front Panel

The front panel includes a digital display, along with several control buttons:

  • I (Green): Start/Power On
  • O (Red): Stop/Power Off
  • S: Set/Enter
  • C: Cancel/Clear
  • ▲ (Up Arrow): Navigate Up/Increase Value
  • ▼ (Down Arrow): Navigate Down/Decrease Value
Front view of the Concord MC-880 air compressor controller, showing the display and control buttons.
Figure 2.1: Front view of the MC-880 Controller

2.2 Back Panel

The back panel houses the electrical connections and a product label detailing model specifics.

Back view of the Concord MC-880 controller, showing the product label with model, voltage, and power details.
Figure 2.2: Back view of the MC-880 Controller with product label

2.3 Product Video Overview

Watch this short video for a visual overview of the product.

Video 2.3: General product overview of the controller.

3. Specifications

FeatureDetail
ModelMC-880 (Variants: V100, V40)
BrandConcord
OriginMainland China
DIY Supplies CategoryElectrical
Voltage220V AC
Frequency50/60Hz
Power Consumption5W
Length22 cm
Width22 cm
Height11 cm
Weight1.0 kg

Note: Always verify the specific model variant (e.g., V100 or V40) and its corresponding voltage requirements as indicated on the product label before installation.

Back view of two MC-880 controllers, showing labels for V100 and V40 variants with their respective specifications.
Figure 3.1: MC-880 Controller variants (V100 and V40) with specification labels

4. Setup

Safety First: Ensure all power to the air compressor system is disconnected before beginning installation. Only qualified personnel should perform electrical installation.

4.1 Mounting

  1. Select a suitable panel location for mounting the controller, ensuring adequate ventilation and protection from moisture and excessive heat.
  2. Cut an opening in the panel according to the controller's dimensions, allowing for a snug fit.
  3. Secure the controller into the panel using appropriate fasteners (screws, clips) through the mounting holes.

4.2 Wiring

  1. Refer to the wiring diagram provided with your air compressor system and the specific terminal markings on the back of the MC-880 controller.
  2. Connect the power supply (220V AC, 50/60Hz) to the designated power input terminals.
  3. Connect control signals for the air compressor (e.g., motor start/stop, pressure sensors, emergency stop) to the corresponding input/output terminals on the controller.
  4. Ensure all connections are secure and properly insulated. Double-check all wiring against the system's electrical schematics.

4.3 Initial Power-Up

  1. After all connections are verified, restore power to the air compressor system.
  2. The controller display should illuminate. If not, check power connections and fuses.
  3. Perform initial configuration as required by your air compressor system's specific needs.

5. Operating Instructions

5.1 Power On/Off

  • To power on the compressor, press the green I button.
  • To power off the compressor, press the red O button.

5.2 Accessing Settings

  • Press the S button to enter the settings menu.
  • Use the ▲ (Up) and ▼ (Down) arrow buttons to navigate through menu options or adjust values.
  • Press S again to confirm a selection or save a value.
  • Press the C button to exit a menu or cancel an operation without saving changes.

5.3 Monitoring

  • The display will typically show real-time operational parameters such as pressure, temperature, or operating status.
  • Use the arrow buttons to cycle through different display modes or monitored values if available.

5.4 Emergency Stop

In case of an emergency, immediately press the main emergency stop button on your air compressor system, which should also cut power to the controller.

6. Maintenance

6.1 Regular Cleaning

  • Keep the controller's display and buttons clean and free from dust, dirt, and moisture.
  • Use a soft, dry cloth for cleaning. Avoid abrasive cleaners or solvents.

6.2 Visual Inspection

  • Periodically inspect the controller for any signs of physical damage, loose connections, or corrosion.
  • Ensure all cables are securely connected and not frayed.

6.3 Environmental Conditions

Ensure the operating environment remains within the specified temperature and humidity ranges to prevent damage to the electronic components.

6.4 Firmware Updates

Consult your air compressor manufacturer for information on potential firmware updates for the controller.

7. Troubleshooting

7.1 Controller Not Powering On

  • Check the main power supply to the air compressor system.
  • Verify the power connections to the controller are secure and correctly wired.
  • Inspect for any blown fuses in the control circuit.

7.2 Display Not Working/Blank

  • Ensure the controller is receiving power.
  • Try cycling the power to the unit.
  • If the issue persists, contact support.

7.3 Compressor Not Starting

  • Check if the controller is in an "OFF" state (red O button pressed).
  • Verify all safety interlocks on the air compressor are satisfied (e.g., pressure switches, thermal overload).
  • Check for any error messages on the controller display and refer to your air compressor's specific manual for error code interpretations.

7.4 Incorrect Readings

  • Ensure all sensors connected to the controller are properly installed and calibrated.
  • Check sensor wiring for damage or loose connections.

For complex issues, consult a qualified technician or contact product support.

8. User Tips

  • Voltage Verification: Always double-check the voltage requirements on the back label of your specific MC-880 unit (e.g., V100 or V40) to ensure compatibility with your power supply.
  • Documentation: Keep this manual and your air compressor's specific documentation handy for quick reference during operation or troubleshooting.
  • Clean Environment: Maintaining a clean and dry environment around the controller can significantly extend its lifespan and prevent malfunctions.

9. Warranty & Support

For technical assistance, questions about the product, or large quantity orders, please contact the seller directly:

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.