TYT TH-9800D Plus Version

Contents

TYT TH-9800D Plus Version Quad Band Mobile Transceiver Instruction Manual

Model: TH-9800D Plus Version | Brand: TYT

Introduction

This manual provides detailed instructions for the safe and efficient operation of your TYT TH-9800D Plus Version Quad Band Mobile Transceiver. This device is a 50W/40W full quad band dual display FM amateur mobile radio/transceiver, suitable for use as a base station. Please read this manual thoroughly before using the transceiver to ensure proper setup and functionality.

TYT TH-9800D Plus Version mobile transceiver with microphone
Figure 1: TYT TH-9800D Plus Version Mobile Transceiver

Setup and Installation

Package Contents

Verify that all items are present in the package:

  • TYT TH-9800D Plus Version Transceiver
  • Microphone with Keypad
  • Mic Hanger
  • Power Cable
  • Mounting Bracket & Screws
  • User Manual (this document)
  • Programming Cable
  • Factory Software Disc
Package contents including the transceiver, microphone, cables, and mounting hardware
Figure 2: Included Accessories

Physical Installation

The transceiver can be installed as a mobile unit in a vehicle or as a base station. Use the provided mounting bracket and screws to secure the unit in a stable location. Ensure adequate ventilation around the unit, especially at the rear, to prevent overheating.

Dimensions of the TYT TH-9800D Plus Version transceiver
Figure 3: Transceiver Dimensions (approx. 5.5 x 1.6 x 6.6 inches)

Power Connection

Connect the provided power cable to the transceiver and to a stable 13.8V DC power source. Ensure correct polarity. WARNING: Do NOT connect to a 24V power source, as this will damage the unit.

Antenna Connection

Connect a suitable 4-band antenna to the SO-259s connector on the rear of the transceiver. Ensure the antenna is properly tuned for the operating frequencies to prevent damage to the radio's final amplifier stage.

Software Installation and Programming

The transceiver includes a programming cable and a factory software disc. Driver installation may be required for the programming cable. The factory software can be downloaded from the disc or the TYT official website. For easier programming, CHIRP software (Model TYT TH-9800) is also supported.

Operating Instructions

Front Panel Controls and Functions

Refer to the diagram below for an overview of the front panel controls and their primary functions. A detailed table follows, explaining each control.

Front panel controls and key functions diagram for the TYT TH-9800D Plus Version
Figure 4: Front Panel Controls
Table 1: Front Panel Key Functions
No.KeyFunction
1LEFT DIAL
  1. Tuning dial for the "Left" band.
  2. Short press the key to set the "Left" band as the "Main" band.
  3. Enable rapid tuning (in 1 MHz steps) when the "Left" band is set to the "Main" band in VFO mode.
  4. Rotate the dial to select the operating band between 28-29.7 MHz, 50-54 MHz, 144-148 MHz, and 420-450 MHz on the left side as VFO/Memory.
2LEFT VOL/SQL
  1. The outer VOL (Volume) control adjusts the "Left" receiver speaker audio level.
  2. The inner SQL (Squelch) control adjusts the "Left" receiver background noise.
  3. Press and hold this knob for 1/2 second to switch the front panel keys LOCK feature "ON" and "OFF".
3LEFT [LOW]
  1. Short press this key to switch power output level of the "Left" band (LOW-MID1-MID2-HIGH).
  2. Press and hold this key for 1/2 second to switch between "VFO" and "Memory" and "Channel Tag" when the "Left" band is set to the Memory mode.
3LEFT [V/M]
  1. Short press the key to switch frequency control for the "Left" band between the VFO and Memory modes.
  2. Press and hold this key for 1/2 second to shift to the "Memory Tuning" feature when the "Left" band is set to the Memory mode.
3LEFT [HM]
  1. Short press to recall a favorite "HOME" frequency memory.
  2. Press and hold in this key for 1/2 second to activate Priority Channel Scanning under VFO or MR mode.
3LEFT [SCN]
  1. Short press the key to activate the Scanner on the "Left" band.
  2. Press and hold in this key for 1/2 second to activate the Scan or Preferred Scan list under MR mode.
4[SET]
  1. Short press the key to enter the Menu mode.
  2. Press and hold in this key for 1/2 second to transfer the contents of the Main band VFO into a Memory channel.
5RIGHT [LOW] (Default)
  1. Short press this key to switch power output level of the "Right" band (LOW-MID1-MID2-HIGH).
  2. Press and hold in this key for 1/2 second to switch display memory mode between "Frequency" and "Channel Tag" when the "Right" band is set to the Memory mode.
6RIGHT [V/M] (Default)
  1. Short press the key to switch frequency control for the "Right" band between the VFO and Memory modes.
  2. Press and hold in this key for 1/2 second to shift to the "Memory Tuning" feature when the "Right" band is set to the Memory mode.
7RIGHT [RPT] (Default)
  1. Short press to change the frequency shift direction: RPT- (minus shift), RPT+ (plus shift), or RPT OFF (simplex).
  2. Press and hold in this key for 1/2 second to activate TX and RX frequencies on the "Main" band.
8RIGHT [TONE] (Default)
  1. Short press to activate the Tone/DCS/DTMF encoder.
  2. Press and hold in this key for 1/2 second to activate CTCSS/DCS (Encoder/Decoder) and DTMF (CTCSS/DCS Encoder & Decoder) or DCS operation.
9RIGHT [SCN] (Default)
  1. Short press the key to activate the Scanner on the "Right" band.
  2. Press and hold in this key for 1/2 second to activate the Scan or Preferred Scan list under MR mode.
10RIGHT [SUB] (Key Mode 2)
  1. Short press to copy the main band frequency to the sub band.
  2. Press and hold in this key for 1/2 second to copy the main band frequency to the sub band and activate the "Sub" band.
11RIGHT VOL/SQL
  1. The outer VOL (Volume) control adjusts the "Right" receiver speaker audio level.
  2. The inner SQL (Squelch) control adjusts the "Right" receiver background noise.
12RIGHT DIAL
  1. Tuning dial for the "Right" band.
  2. Short press the key to set the "Right" band as the "Main" band.
  3. Enable rapid tuning (in 1 MHz steps) when the "Right" band is set to the "Main" band in VFO mode.
  4. Rotate the dial to select the operating band between 28-29.7 MHz, 50-54 MHz, 144-148 MHz, and 420-450 MHz on the right side as VFO/Memory.
13Typical Memory Keys [A] - [F]
  1. Short press the key to recall a favorite "HOME" frequency memory.
  2. Short press the appropriate key to recall the desired "Memory" channel.

Basic Operation

  • Power On/Off: Press and hold the power button (usually integrated with a volume knob) to turn the unit on or off.
  • Volume Adjustment: Use the LEFT VOL/SQL and RIGHT VOL/SQL knobs to adjust the audio output level for each band.
  • Frequency Tuning: Use the LEFT DIAL and RIGHT DIAL to tune frequencies in VFO mode. Short press the dial to set the respective band as the main band.
  • Memory Channels: The transceiver supports 809 alphanumeric memory channels. Use the [V/M] key to switch between VFO (Variable Frequency Oscillator) and Memory modes.
  • Dual Display and Receive: The unit features full dual display, allowing simultaneous monitoring of two different frequencies (V/V, U/U, V/U).
  • Cross-Band Repeater: The TH-9800D Plus supports V+U cross-band repeater functionality. Refer to the advanced settings in the menu for configuration.
  • Power Setting: Adjust the output power (High/Mid1/Mid2/Low) using the [LOW] key for each band independently.
  • Bandwidth Selection: Select Wide/Mid/Narrow bandwidth as needed for different signal conditions.
  • CTCSS/DCS, DTMF, 2 Tone & 5 Tone: These signaling features can be configured via the menu system and activated using the [TONE] key.
  • Voice Compander & Scrambler: Enhance audio clarity and privacy using these features, accessible through the menu.
  • Remote Detachable Faceplate: The faceplate can be detached for flexible installation options.

Maintenance

  • Cleaning: Use a soft, dry cloth to clean the exterior of the transceiver. Do not use harsh chemicals or solvents.
  • Ventilation: Ensure that the cooling fins on the rear of the unit are not obstructed to allow for proper heat dissipation.
  • Temperature: Avoid operating the transceiver in extremely hot or cold environments. The rear surface can become hot during prolonged use; avoid touching it after long-term operation.
  • Connections: Periodically check all cable connections (power, antenna, microphone) to ensure they are secure and free from damage.
Rear view of the transceiver showing cooling fins and warning label
Figure 5: Rear Panel with Cooling Fins and Temperature Warning

Troubleshooting

If you encounter issues with your transceiver, consider the following basic troubleshooting steps:

  • No Power: Check the power cable connection and ensure the 13.8V DC power source is active. Verify correct polarity.
  • No Audio: Check volume levels for both left and right bands. Ensure squelch (SQL) is not set too high.
  • Cannot Transmit: Verify antenna connection. Check power output settings. Ensure the frequency is within the allowed transmit range.
  • Poor Reception: Check antenna connection and ensure it is properly tuned. Adjust squelch level. Check for local interference.
  • Programming Issues: Ensure the programming cable drivers are correctly installed. Verify that the correct software version (factory or CHIRP for TH-9800) is being used.

For more complex issues, consult the full user manual (if available as a separate PDF) or contact customer support.

Specifications

FeatureDetail
ModelTH-9800D Plus Version
Transmit Frequency (TX)28-29.7 MHz, 50-54 MHz, 144-148 MHz, 420-450 MHz
Receive Frequency (RX)26-33 MHz, 47-54 MHz, 108-180 MHz, 320-512 MHz, 750-950 MHz (AM mode selectable on VHF receive for Air Band)
Output Power (VHF)50W / 20W / 10W / 5W
Output Power (UHF)35W / 20W / 10W / 5W
Operating Voltage13.8V DC
Dimensions (W x H x D)Approx. 5.5 x 1.6 x 6.6 inches (140 x 40 x 168 mm)
WeightApprox. 2.65 lbs (1.2 kg)
Memory Channels809 Alphanumeric
Key FeaturesV/V, U/U, V/U Simultaneous Receive, V+U Cross-Band Repeater, Full Dual Display, High/Mid1/Mid2/Low Power Setting, Wide/Mid/Narrow Bandwidth, CTCSS/DCS, DTMF, 2 Tone & 5 Tone, Voice Compander & Scrambler, Remote Detachable Faceplate, SQL, Scan, TOT, Full Direct Entry Keypad Mic.

User Tips

  • Programming Software: Many users find CHIRP software to be a more user-friendly alternative for programming memory channels and settings compared to the factory software. Ensure you select the correct model (TYT TH-9800) within CHIRP.
  • Antenna Matching: For optimal performance and to prevent damage, always use a 4-band antenna specifically designed for the operating frequencies of this transceiver and ensure it is properly matched.
  • Cooling: During high-power transmissions or extended use, the unit can generate significant heat. Ensure it is mounted in a location with good airflow, especially around the rear cooling fins.

Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the documentation provided at the time of purchase or contact your authorized dealer. Keep your purchase receipt as proof of purchase.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.